Publications
Filters
total: 1026
displaying 1000 best results Help
Catalog Publications
Year 2017
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
CHARAKTERYSTYKA WYMIANY CIEPŁA I OPORÓW PRZEPŁYWU OMYWANIA MIKROSTRUGAMI ROZWINIĘTEJ POWIERZCHNI
PublicationW artykule przedstawiono eksperymentalne badania kompaktowego wymiennika ciepła z intensyfikacją przejmowania ciepła przy użyciu mikrostrug. Niniejszy artykuł przedstawia projekt i testy prototypu, wymiennika ciepła typu mikrostrugowego. Modułowa konstrukcja wymiennika umożliwia zmianę wymiarów geometrycznych, a także zmianę materiału przegrody wymiennika ciepła. Metoda graficzna Wilsona została z zastosowana w celu określenia...
-
Co zrobić z nieużywaną wieżą ciśnień? Studium historyczno-koncepcyjne (część I)
PublicationArtykuł przedstawia historię i (dawną) funkcję wieży ciśnień (obecnie nieużytkowanej, stanowiącej konstrukcyjną część budynku Laboratorium Maszynowego Politechniki Gdańskiej. Jest to wstęp do przedstawienia koncepcji adaptacji tego obiektu na modelową mikro-elektrownię szczytowo-pompową, mogącą posłużyć badaniom i dydaktyce.
-
Co zrobić z nieużywaną wieżą ciśnień? Studium historyczno-koncepcyjne (część II)
PublicationDruga część artykułu przedstawia obliczenia parametrów pracy, jakich można się spodziewać, realizując koncepcję mikro-elektrowni szczytowo-pompowej w oparciu o adaptację nieczynnej wieży ciśnień stanowiącej część budynku Laboratorium Maszynowego. Przedstawiona została także analiza możliwości współpracy z istniejącą instalacją fotowoltaiczną w kierunku uzyskania kompletnego mikro-systemu energetycznego.
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublicationThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublicationCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublicationThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublicationIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublicationCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublicationThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublicationThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Diagnozowanie turbin parowych
PublicationDiagnozowanie turbin parowych jest to istotny proces mający na celu utrzymanie diagnozowanego obiektu w stanie zdatności zadaniowej z jak największą sprawnością. W procesie diagnozowania turbin wykorzystuje się diagnostykę cieplno-przepływową, należy do diagnostyki technicznej zajmującej się badaniem oraz oceną przemian energetycznych.
-
Elektrociepłownie- przegląd rozwiązań
PublicationW artykule przedstawione i opisane zostały rożnego typu układy elektrociepłowni. Systemy zostały sklasyfikowane ze względu na konstrukcję. Przedstawione zostały główne wady i zalety każdego rozwiązań. Artykuł ukazuje również zalety kogeneracji jako sposobu wytwarzania w bardziej efektywny sposób energii elektrycznej oraz cieplnej.
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublicationIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Flow Analysis of a Kaplan Turbine
PublicationThis monograph is a guide to a method of experimental and numerical flow investigations for Kaplan - type turbines. The numerical calculations were compared with the test results of the model Kaplan turbine. The tests were carried out on the model test rig in the Gdańsk University of Technology. The turbine has been thoroughly experimentally investigated, resulting in the identification of optimum setting combination of the stator...
-
High Temperature Drying Process of Beech Wood (Fagus sylvatica L.) with Different Zones of Sapwood and Red False Heartwood
PublicationThis study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential)....
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublicationIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
How much a geometrical model of a honeycomb seal can be simpli ed in the CFD calculation
PublicationThis paper presents the inuence of geometry simplication on the results obtained in the computational fluid dynamics simulation. The subject of simulation was part of the honeycomb seal located at the inlet to high pressure part of a steam turbine. There were three different geometrical models assumed in the calculations. First one was two-dimensional case and two others were three dimensional, one with the radius of curvature...
-
INTENSYFIKACJA WYMIANY CIEPŁA W WYMIENNIKU WĘŻOWNICOWYM Z WYKORZYSTANIEM PRZEGRÓD O RÓŻNEJ GEOMETRII
PublicationW pracy zaprezentowano możliwości wykorzystania pasywnej intensyfikacji wymiany ciepła w postaci przegród dla podniesienia efektywności energetycznej wymiennika wężownicowego. Badania zostały przeprowadzone z wykorzystaniem modułowego wymiennika z wężownicą w postaci grzałki elektrycznej. Medium odbierającym ciepło była woda o stałych parametrach cieplnoprzepływowych na wlocie do modułu. Pomiary przeprowadzono dla szerokiego zakresu...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
Kurs na energię
PublicationJednym z nadrzędnych celów, jakie stawia przed sobą Unia Europejska, jest realizacja tzw. polityki zrównoważonego rozwoju. Ma ona polegać na implikacji sprzyjających warunków dla powstania konkurencyjnej gospodarki niskoemisyjnej.
-
Liquid Crystals, PIV and IR-Photography in Selected Technical and Biomedical Applications
PublicationThermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV), Infrared Imaging Themography (IR) and True-Colour Digital Image Processing (TDIP) have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. These four tools (based on the desktop computers) have come together during the past two decades to produce a powerful advanced...
-
Metody intensyfikacji wymiany ciepła "po stronie płaszcza" w kompaktowym wężownicowym wymienniku ciepła
PublicationZe względu na rosnącą populację i zwiększające się zanieczyszczenie środowiska naturalnego coraz aktualniejsza staje się tematyka wysokosprawnych wymienników ciepła . Elementy te mają duże znaczenie dla systemów energetycznych, instalacji chłodniczych i wentylacyjnych oraz inżynierii spożywczej i chemicznej . Jedną z częściej spotykanych konstrukcji jest wężownicowy aparat cieplny . Ten typ aparatu cieplnego został opracowany w...
-
Metody intensyfikacji wymiany ciepła w kompaktowym wymienniku ciepła typu rura w rurze
PublicationAparaty cieplne typu rura w rurze ze względu na prostotę swojej geometrii oraz łatwo powtarzalny proces produkcji nadal są jednymi z czołowych rozwiązań wykorzystywanych w wielu przemysłowych aplikacjach . Wykorzystuje się je od systemów chłodniczych i klimatyzacyjnych po instalacje cieplne czy nawet układy spotykane na stacjach kosmicznych lub statkach powietrznych. W zależności od systemu technicznego pierwszoplanowa rolę przy...
-
MIKROSTRUGOWA TECHNIKA INTENSYFIKACJI WYMIANY CIEPŁA W PŁASZCZOWO-RUROWYM WYMIENNIKU CIEPŁA
PublicationW pracy przedstawiono opatentowaną konstrukcję mikrostrugowego wymiennika ciepła o budowie cylindrycznej, wraz z wynikami jego systematycznych badań eksperymentalnych w warunkach konwekcji jednofazowej oraz modelowania współczynników przejmowania ciepła. W oparciu o pozyskane wyniki przeprowadzono również walidację wybranych korelacji opisujących liczbę Nusselta, dostępnych w literaturze przedmiotu. Oceny stopnia intensyfikacji...
-
Minimum drag shape bodies moving in inviscid fluid - revisited
PublicationThis paper presents the classic approach to minimum drag shape body problem, moving at hypersonic speeds, leading to famous power law shapes with value of the exponent of 3/4. Two- and three-dimensional cases are considered. Furthermore, an exact pseudo solution is given and its uselessness is discussed. Two new solutions are introduced, namely an approximate solution due to form of the functional and solution by means of optimisation...
-
Moduł eksperymentalny do badania wężownicowych wymienników ciepła
PublicationArtykuł dotyczy badań eksperymentalnych modułu do badania wężownicowych wymienników ciepła. Opracowanie zawiera przykłady zastosowania wymienników z wężownicami, opis stanowiska oraz wstępne badania.
-
Optimization of chip removing system operation in circular sawing machine
PublicationThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Performance of the PEM fuel cell module. Part 2. Effect of excess ratio and stack temperature
PublicationThe paper describes a fuel cell based system performance under different thermal conditions. The system could be fed with bottled hydrogen or with very high purity hydrogen obtained from reforming of methanol. The system is based on two fuel cell units (1.2 kW each, produced by Ballard Power Systems Inc. and called Nexa), DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and...
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublicationIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Projekt stanowiska badawczego do wyznaczania charakterystyki ogólnej silnika spalinowego ZS przy wykorzystaniu hydraulicznego układu odbioru mocy
PublicationPrzedstawiono projekt stanowiska badawczego służącego do wyznaczania charakterystyki ogólnej silnika pojazdu ciężarowego, wykorzystując przystawkę odbioru mocy do napędu układu hydraulicznego generującego obciążenie silnika w różnych punktach jego pracy. Przedstawiono założenia projektowe oraz ograniczenia konstrukcyjne. Omówiono zasadę działania stanowiska i metodę wyznaczania charakterystyki. Opisano układ hydrauliczny oraz układ...
-
Projekt wężownicowego wymiennika ciepła
PublicationPrzedmiotem niniejszego artykułu jest zaprezentowanie konstrukcji wężownicowego wymiennika ciepła powstałej w ramach pracy inżynierskiej w Katedrze Energetyki i Aparatury Przemysłowej. Podstawowym założeniem pracy było zoptymalizowanie aparatu cieplnego w taki sposób, aby możliwe było jak najefektywniejsze przekazywanie ciepła do przepływającego płynu. Oparto się tu przede wszystkim na rozważaniach dotyczących wpływu modyfikacji...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Shape Optimisation of Kaplan Turbine Blades Using Genetic Algorithms
PublicationThis monograph is a comprehensive guide to a method of blade profile optimisation for Kaplan-type turbines. This method is based on modelling the interaction between rotor and stator blades. Additionally, the shape of the draft tube is investigated. The influence of the periodic boundary condition vs. full geometry is also discussed. Evolutionary algorithms (EA) are used as an optimisation method together with artificial neural...
-
Small Scale Gasification of Biomass and Municipal Wastes for Heat and Electricity Production using HTAG Technology
PublicationCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900degC provides additional energy to conversion processes and results in considerable...
-
Sposoby zagospodarowania ciepła odpadowego z silników jednostek pływających Cześć 2. Wykorzystanie ciepła do ogrzewania
PublicationW pierwszej części artykułu (COW 2/2017) omówiono możliwości wykorzystania nieużytkowej energii chemicznej paliwa do chłodzenia jednostek pływających. W drugiej części autorzy opisali systemy pozwalające wykorzystać tę energię do ogrzewania. Oprócz opisania budowy układów pozwalających na wykorzystanie ciepła odpadowego do ogrzewania, porównano je pod względem wydajności. Podjęto także próbę wskazania rozwiązania o najwyższej efektywności...
-
Sposoby zagospodarowania ciepła odpadowego z silników napędowych jednostek pływających Cześć 1. Wykorzystanie ciepła do napędu urządzeń chłodniczych
PublicationEnergia chemiczna paliwa jest w wielu przypadkach zaledwie w połowie wykorzystana jako energia napędowa silnika. Pozostała część jako ciepło odpadowe przekazywana jest do otoczenia. Dzięki odpowiednim układom przetwarzania ciepło ze spalin można wykorzystać do wytwarzania chłodu lub jako ciepło użytkowe, w systemach HVAC (ang. heating, ventilation, air conditioning – ogrzewanie, wentylacja, klimatyzacja). Tym samym koszty pracy...
-
Structural optimization of microjet array cooling system
PublicationThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublicationIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
The influence of the drying process on the deformation of the beech and oak wood samples
PublicationThe influence of the drying process conditions on the deformation of the beech and oak wood. The results of the deformation of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur) after drying process are presented. The drying process was carried out in the same drying schedule for each wood species. During each of schedules 40 pieces of wood were dried. The samples were divided into two groups. The first group of tested...
-
The performance of H2O, R134a, SES36, ethanol, and HFE7100 two-phase closed thermosyphons for varying operating parameters and geometry
PublicationIn this study, the influences of different parameters at performance two-phase closed thermosiphon (TPCT) was presented. It has been confirmed that the working fluid, as well as operating parameters and fill ratio, are very important factors in the performance of TPCT. The article shows characteristics of gravitational tube geometr ies, as well as the technical characteristic of the most important system components, i.e., the evaporator/condenser....
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublicationThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Tradycyjna lodownia – ekoenergetyczny magazyn żywności
PublicationW artykule omówiono konstrukcję oraz zasadę działania naturalnych przechowalni żywności, tzw. lodowni. Przedstawiono kilka przykładów takich konstrukcji wraz z opisem ich budowy. Na przykładzie jednego rozwiązania szczegółowo opisano zasadę działania procesów zachodzących wewnątrz przechowalni. Podkreślono neutralność tego typu budowli wobec środowiska. Przedstawiono zalety i wady analizowanego rozwiązania na tle sprężarkowych...
-
Turbiny parowe i gazowe
PublicationArtykuł opisuje turbiny parowe i gazowe. Autorka przedstawia chronologię wynalezienia turbin ich zasadę działania i najważniejsze zastosowania. W pracy przedstawione zostały różnice między turbinami parowymi i gazowymi i wynikające z tego wady i zalety obu rozwiązań.
-
Turbomachinery - Background
PublicationThe "Turbomachinery - Background" is the first part of a series of monographs devoted to different aspects of rotating machines. The book presents the main fundamentals which are necessary for the different problems of steam, gas, wind and water turbines as well as pumps, compressors and propellers which will discussed in detail in the subsequent parts of the series.
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy
PublicationW artykule przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonano w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podsatwie określono zmianę sprawności...
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy.
PublicationW referacie przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonane zostały w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podstawie określono...
Year 2016
-
A novel concept of H2/O2 steam generator
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublicationPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
AN EXPERIMENTAL AND NUMERICAL STUDY ON THE PERFORMANCE OF AN INNOVATIVE VERTICAL-AXIS WIND TURBINE
PublicationThis paper introduces the innovative modification of the Savonius wind turbine being able to significantly increase efficiency in comparison with the classic design. This innovative design is equipped with a stator directing the flow. The presence of the stator increases the active surface area and generates higher torques acting on a shaft. Additionally, it makes it possible to take better advantage of wind energy and compensate...
-
Analiza efektywności odzysku ciepła odpadowego z zastosowaniem rurki ciepła. Cz. 2: Badana eksperymentalne
PublicationNiniejszy artykuł jest kontynuację tematyki podjętej w części pierwszej [5]. Materiał został uzupełniony o podstawową wiedzę na temat modelowania termosyfonu dwufazowego oraz rozszerzony opis zmodyfi kowanego stanowiska badawczego wraz z dokładna charakterystyką badanych geometrii (rurek grawitacyjnych), jak również newralgicznych elementów układu - parownik/skraplacz. Autorzy przedstawiają plan eksperymentu, oraz wyniki badań...
-
Analysis of possible application of high-temperature nuclear reactors to contemporary large-output steam power plants on ships
PublicationThis paper is aimed at analysis of possible application of helium to cooling high-temperature nuclear reactor to be used for generating steam in contemporary ship steam-turbine power plants of a large output with taking into account in particular variable operational parameters. In the first part of the paper types of contemporary ship power plants are presented. Features of today applied PWR reactors and proposed HTR reactors...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublicationThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublicationThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
Badania efektywności energetycznej pompy ciepła typu GEJZER KOMPAKT W 11
PublicationBadania eksperymentalne, analizy teoretyczne oraz weryfikacja klasy energetycznej sprężarkowej pompy ciepła woda-woda typu GEJZER KOMPAKT W 11 w świetle wymagań Dyrektywy Parlamentu Europejskiego
-
Badania eksperymentalne formowania się kondensatu na zmodyfikowanej powierzchni wymiany ciepła, część 1: podstawy teoretyczne i budowa układu pomiarowego.
PublicationW artykule przedstawiono koncepcję stanowiska naukowo-dydaktycznego, które ma posłużyć do lepszego poznania procesów przemian fazowych w obecności gazów inertnych oraz przy wykorzystaniu nowoczesnych metod intensyfikacji powierzchni celem zwiększenia intensywności wymiany ciepła.
-
Badania eksperymentalne mikroturbozespołów
PublicationW pracy zaprezentowano rezultaty badań eksperymentalnych mikroturbozespołów parowych pracujących w zmiennych warunkach ruchu. Opisywane testy dotyczyły właściwości kompletnego urządzenia jakim jest mikroturbozespół, a nie wyłącznie jego podzespołów: mikroturbiny lub generatora elektrycznego. Badania przeprowadzono na pięciu różnych mikroturbozespołach różniących się typem generatora elektrycznego oraz typem konstrukcyjnym turbiny....
-
Chłodzenie wyparne jako alternatywna metoda chłodzenia powietrza w klimatyzacji - podstawy termodynamiczne
PublicationW pracy przedstawiono podstawy termodynamiczne chłodzenia wyparnego. Omówiono cztery sposoby realizacji takiego procesu, tj. poprzez chłodzenie bezpośrednie, pośrednie, metodę hybrydową (pośrednią/bezpośrednią) oraz metodę mieszaną, która łączy chłodzenie wyparne z tradycyjnymi metodami sprężarkowymi. Przedstawiono rozważania związane z zapotrzebowaniem na wodę dla poszczególnych rodzajów chłodzenia, jak również oszacowano skutki...
-
Chłodzenie wyparne jako alternatywna metoda chłodzenia powietrza w klimatyzacji - przykłady zastosowań
PublicationW pracy przedstawiono przykłady zastosowań chłodzenia wyparnego. Z literatury zaczerpnięto znane realizacje instalacji wykorzystujących chłodzenie wyparne. Przedstawiono koncepcję urządzenia opartą na wykorzystaniu istniejącego na rynku wymiennika do chłodzenia wyparnego powietrza. Porównano pracę instalacji w różnych strefach klimatycznych. Odniesiono metodę wyparną do klasycznej, sprężarkowej, ukazując jakie korzyści finansowe...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Continuous Optimisation Algorithms
PublicationKsiążka poświęcona jest zagadnieniom optymalizacji ciągłej. Oprócz klasycznych algorytmów gradientowych omawiane są w współczesne algorytmy bezgradientowe, które stosowane są z powodzeniem w optymalizacji globalnej. Większość prezentowanych algorytmów określona może być mianem metaheurystycznych. Zaliczyć do nich można metody optymalizacji inspirowane procesami zachodzącymi w przyrodzie, które dalej można dzielić na inspirowane...
-
Criteria for selection of working fluid in low-temperature ORC
PublicationThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
Diagnostyka cieplno-przepływowa turbin parowych
PublicationDiagnostyka cieplno-przepływowa należy do diagnostyki technicznej zajmuje się ona badaniem oraz oceną przemian energetycznych. Głównym zadaniem diagnostyki cieplno-przepływowej jest utrzymanie obiektu w stanie jak ja wyższej sprawności. W referacie tym omawianym obiektem jest turbina parowa występująca w elektrowniach.
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublicationAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Elektrownie jądrowe- historia i przegląd typów reaktorów
PublicationElektrownie jądrowe stanowią jedno ze źrodeł produkcji energii. Produkują one duże ilości energii z małej ilości surowca. Reaktry jądrowe są stale rowijane technologicznie, po to aby byly one jeszcze bezpieczniejsze, a także aby pracowały z coraz to wyższymi sprawnościami
-
Energochłonność pralnic przemysłowych z technologią ozonowania
PublicationW wyniku wprowadzenia ozonu do procesu czyszczenia uzyskuje się lepszą jakość wody usuwanej z procesów prania do kanalizacji. Woda będąca pozostałością po zakończonym procesie zawiera między innymi mniej pozostałości środków chemicznych, mniej pozostałości patogenów oraz posiada stabilne pH. Ponadto użycie ozonu w procesie czyszczenia tkanin prowadzi do redukcji zużycia wody i energii w poszczególnych cyklach płukania i suszenia,...
-
Experimental analysis of chip removing system in circular sawing machine
PublicationPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublicationIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Experimental investigation of domestic micro-CHP based on the gas boiler fitted with ORC module
PublicationThe results of investigations conducted on the prototype of vapour driven micro-CHP unit integrated with a gas boiler are presented. The system enables cogeneration of heat and electric energy to cover the energy demand of household. The idea of such system is to produce electricity for own demand or for selling it to the electric grid – in such situation the system user will became the prosumer. A typical commercial gas boiler,...
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublicationIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation of free convection of glycol-Al2O3 nanofluid from horizontal tube
PublicationNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
EXPERIMENTAL INVESTIGATION OF FREE CONVECTION OF GLYCOL-Al2O3 NANOFLUID FROM HORIZONTAL TUBE
PublicationNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Gas turbines – technological development and potential use in CAES systems
PublicationThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Gazowy kocioł kogeneracyjny – badania prototypu
PublicationW artykule zaprezentowano wyniki badań prototypowej parowej mikrosiłowni ORC zintegrowanej z kotłem gazowym. Jest to pierwsze w Polsce tego typu urządzenie w skali „domowej”, uhonorowane złotym medalem na targach Technicon Innowacje 2014. Pozwala realizować kogeneracyjną produkcję ciepła i energii elektrycznej w aspekcie pokrycia potrzeb indywidualnego gospodarstwa domowego. Domowy kocioł gazowy doposażony w układ realizujący obieg...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublicationThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
High temperature drying of beech with content of tension wood
PublicationThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublicationResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Laboratorium Mechaniki Płynów
PublicationKsiążka poświęcona jest zagadnieniom pomiarowym w mechanice płynów. Zawiera opis szeregu ćwiczeń laboratoryjnych związanych z przepływami. Książka przeznaczona jest dla studentów wydziałów mechanicznych i pokrewnych.
-
Magazynowanie ciepła i chłodu uzyskanych dzięki wykorzystaniu ciepła odpadowego z silników jednostek morskich
PublicationPrzetworzenie ciepła odpadowego ze spalin silników diesla stwarza możliwości jego wykorzystania do ogrzewania, chłodzenia, a także wytwarzania energii elektrycznej. Dzięki temu możliwe jest obniżenie kosztów zapewnienia komfortu cieplnego w pomieszczeniach na statku. W dalszej części autorzy omówili możliwości magazynowania ciepła bądź chłodu w celu pokrycia późniejszego zapotrzebowania. Opisane zostały różne materiały wypełniające...
-
Magazyny ciepła ze złożem naturalnym i złożem na bazie materiałów zmiennofazowych
PublicationW artykule zaprezentowano możliwości wykorzystania magazynowania energii w technologii budowlanej. Przedstawiono najnowsze trendy rozwoju tej technologii w oparciu o wykorzystanie materiałów zmiennofazowych oraz nowoczesnych materiałów konstrukcyjnych . Pokazano historyczne jak i najnowsze rozwiązania magazynów i obiektów budowlanych z nimi współpracujących. Autorzy dokonali swoistego przeglądu rozwiązań mogących mieć zastosowanie...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublicationIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Modelling of blood flow: from macro to microscales
PublicationThe aim of this paper it to review various scale approaches to blood flow modelling. Blood motion may be described by three types of mathematical models according to the observed scales or resolutions, namely microscopic, mesoscopic and macroscopic description. The above approaches are discussed together with their advantages and disadvantages. Several results of mesoscopic simulations are presented.
-
Modelowanie niepewności pomiarowych obiegu turbo parowego.
PublicationArtykuł opisuje próbę stworzenia modelu neuronowego wymiennika regeneracyjnego siłowni kondensacyjnej pracującego w zmiennych warunkach ruchu. Wzorzec poprawnej pracy elementów siłowni turboparowej jest pożądany w dziedzinie diagnostyki, ponieważ poprawnie pracujący model neuronowy jest w stanie zastąpić czasochłonne obliczenia bilansowe.
-
Modelowanie niepewności pomiarowych obiegu turboparowego
PublicationArtykuł opisuje próbę stworzenia modelu neuronowego wymiennika regeneracyjnego siłowni kondensacyjnej pracującego w zmiennych warunkach ruchu. Wzorzec poprawnej pracy elementów siłowni turboparowej jest pożądany w dziedzinie diagnostyki, ponieważ poprawnie pracujący model neuronowy jest w stanie zastąpić czasochłonne obliczenia bilansowe.
-
Modelowanie przeplywu pary przez okołodźwiękowe wieńce turbinowe przy użyciu sztucznych sieci neuronowych
PublicationNiniejszy artykul stanowi opis modelu przepływu pary przez okołodźwiękowe stopnie turbinowe, stworzonego w oparciu o sztuczne sieci neuronowe (SSN). Przedstawiony model neuronowy pozwala na wyznaczenie rozkladu wybranych parametrów w analizowanym przekroju kanalu przeplywowego turbiny, dla rozpatrywanego zakresu wartości ciśnienia wlotowego.
-
Modelowanie przepływu pary przez okołodźwiękowe wieńce turbinowe z użyciem sztucznych sieci neuronoych
PublicationNiniejszy artykuł stanowi opis modelu przepływu pary przez okołodźwiękowe stopnie turbinowe, stworzonego w oparciu o sztuczne sieci neuronowe (SSN). Przedstawiony model neuronowy pozwala na wyznaczenie rozkładu wybranych parametrów w analizowanym przekroju kanału przepływowego turbiny dla rozpatrywanego zakresu wartości ciśnienia wlotowego.