Wyszukiwarka
Filtry
wszystkich: 595
wybranych: 499
Wyniki wyszukiwania dla: FLUID FLOW
-
Volute scroll as an alternative to guide vanes at inlet to turbine.
PublikacjaW pracy przedstawiono alternatywny sposób zasilania turbin parowych poprzez zastosowanie podwójnej spirali zasilającej. Przedstawiono model jednowymiarowy obliczania przepływu przez spirale oraz zamieszczono wyniki obliczeń typu 3D. Pokazano jak zależy parametr nierównomierności rozkładu prędkości na wylocie od sposobu kształtowania przekroju spiral.
-
Motion of a sphere in vicinity of the wall
PublikacjaArtykuł skupiony jest na badanich odchylenia toru cząstki w sąsiedztwie ścianki. Cząstka modelowana jest nieodkształcalną kulą zawieszoną na strunie. Systematyczne badania z wykorzystaniem kul o trzech średnicach wykonano na specjalnie zbudowanym stanowisku eksperymentalnym. Zaproponowano autorską matematyczną korelację opisującą oddziaływanie ścianki na ruch cząstki - korelacja określa to oddziaływanie w funkcji początkowej odległości...
-
Experimental investigations of hydraulic jump created by a two-phase impin-ging jet on a solid surface
PublikacjaPrzedstawiono rezultaty badań eksperymentalnych powstawania uskoku hydraulicznego tworzonego przez dwufazową strugę uderzającą.
-
Experimental and theoretical study of surface cooling using a single microjet
PublikacjaPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
DEVELOPMENT OF A COUPLED NUMERICAL AND EXPERIMENTAL APPROACH TO HYDRODYNAMIC NOISE ESTIMATION
PublikacjaThe hydroacoustic signature of ships' propellers can be estimated experimentally through measurements of cavitation-induced pressure fluctuations and the corresponding noise distributions at model scale. These measurements need to be performed in a cavitation tunnel under the propellers operating conditions and are quite sensitive and challenging to perform with sufficient accuracy. In comparison, the numerical approach can be...
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublikacjaThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Clean gas technologies - towards zero-emission repowering of Pomerania.
PublikacjaThe main aim this work is to show the different thermodynamic cycles which improve efficiency and/or decrease emission like: Cheng cycle, Szewalski cycle, LOTHECO cycle, hybrid pSOFC/GT cycle, inverse Brayton cycle, low-emission cycle and zero-emission cycle. For that purpose, cycles and results of analysis are first studied and, secondly, new concept is presented. The role of coupled analysis 0D and 3D in cycle’s devices is also...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublikacjaDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Enhancement of the Brayton cycle efficiency by water or steam utilization
PublikacjaIn the paper, thermodynamic analysis of two modifications of a Brayton cycle into enhancement cycles with water/steam injection are discussed. The first one deals with a STIG modified system with both interstage compressed air cooling and air heating (heat regeneration) before combustion chamber. The second one, mainly devoted to higher steam/air ratio, is connected with separate steam production in a HRSG. The analysis has been...
-
Kinetic analysis of the stage for a high speed steam turbine
PublikacjaThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
Design criterion for hydrodynamic vortex separators
PublikacjaTechnical objects designing involves determination of geometrical parameters that characterize a given object. When the device is described by the differential equations, an inverse problem brings difficulties, as geometrical values sought condition the solution to the problem. Vortex separators can be designed by the "criterion method'. Firstly, a critical particle is distinguished such that bigger particles are removed from...
-
Numerical investigation of multiphase blood flow coupled with lumped parameter model of outflow
PublikacjaPurpose The purpose of this paper is the application of the computational fluid dynamics model simulating the blood flow within the aorta of an eight-year-old patient with Coarctation of Aorta. Design/methodology/approach The numerical model, based on commercial code ANSYS Fluent, was built using the multifluid Euler–Euler approach with the interaction between the phases described by the kinetic theory of granular flow (KTGF). Findings A...
-
A new model of fuel spray shape at early stage of injection in a marine Diesel engine
PublikacjaIn the cylinders of a marine diesel engine, self-ignition occurs in very shortly time after the fuel injection into the combustion chamber. Therefore, the paper present was to develop a model of diesel fuel spray for the early stage of fuel spray for in marine diesel engine. There were taken into consideration the main aspects technical such as nozzle diameter of marine engine injector and backpressure in combustion chamber. In...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublikacjaPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Effects of subfilter velocity modelling on dispersed phase in LES of heated channel flow
PublikacjaA non-isothermal turbulent flow with the dispersed phase is modelled using the Large Eddy Simulation (LES) approach for fluid, one-way coupled with the equations of point-particle evolution. The channel is heated at both walls and isoflux boundary conditions are applied for fluid. Particle velocity and thermal statistics are computed. Of particular interest are the r.m.s. profiles and the probability density function of particle...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Analysis of the radiation dose in UV-disinfection flow reactors.
PublikacjaTheoretical considerations devoted to the variation of UV radiation doses in flow disinfection reactors are presented. The minimal time required by the fluid to pass the reactor was determined and combined with the radiation intensity. The active zones of the reactor were determined.
-
Steady magnetohydrodynamic flow in a diverging channel with suction or blowing
PublikacjaAn analysis is made of steady two-dimensional divergent flow of an electrically conducting incompressible viscous fluid in a channel formed by two non-parallel walls, the flow being caused by a source of fluid volume at the intersection of the walls. The fluid is permeated by a magnetic field produced by an electric current along the line of intersection of the channel walls. The walls are porous and subjected to either suction...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Free-surface elevation in open vortex flow controls
PublikacjaRotational form of fluid motion is complex, but very important in science and technology. The paper is devoted to the hydraulic mechanism of flow in open vortex flow controls, or regulators. The velocity field was described by the kinematic model, and intensity of rotation - by means of the energy balance between the input and dissipation. In consequence some algebraic expresions were obtained, which can be useful in approximated...
-
The vortex flow caused by sound in a bubbly liquid
PublikacjaGeneration of vorticity in the field of intense sound in a bubbly liquid in the free half-space is considered. The reasons for generation of vorticity are nonlinearity, diffraction, and dispersion. Acoustic streaming differs from that in a Newtonian fluid. Under some conditions, the vortex flow changes its direction. Conclusions concern streaming induced by a harmonic or an impulse Gaussian beam.
-
Study of Slip Effects in Reverse Roll Coating Process Using Non-Isothermal Couple Stress Fluid
PublikacjaThe non-isothermal couple stress fluid inside a reverse roll coating geometry is considered. The slip condition is considered at the surfaces of the rolls. To develop the flow equations, the mathematical modelling is performed using conservation of momentum, mass, and energy. The LAT (lubrication approximation theory) is employed to simplify the equations. The closed form solution for velocity, temperature, and pressure gradient...
-
Experiments and Analysis of the Limit Stresses of a Magnetorheological Fluid
PublikacjaPaper presents the results of a rheological test of a commercial magnetorheological (MR) fluid (MRF-132DG). The researchincludes the problem of measuring and interpreting limit stresses under conditions close to the magnetic saturation of the fluid. Fourdifferent limit stresses were determined, two related to the yield point and two related to the flow point. Methods for determining limitstresses, especially due to excitation...
-
Neural network simulator's application to reference performance determination of turbine blading in the heat-flow diagnostics.
PublikacjaIn the paper, the possibility of application of artificial neural networks to perform the fluid flow calculations through both damaged and undamaged turbine blading was investigated. Preliminary results are presented and show the potentiality of further development of the method for the purpose of heat-flow diagnostics.
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublikacjaIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublikacjaIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Criteria for selection of working fluid in low-temperature ORC
PublikacjaThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
The calculation long-term physical field created by water flow around the ship
PublikacjaThe paper presents a description of the problems with fluid flow around a ship. Using the described solution of the problem were performed numerical calculations using the boundary element method. Were also presented preliminary results of the calculation of pressure fields at the bottom of the ship, taking into account the impact of the bottom.
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublikacjaIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublikacjaThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
Fluid structure interaction study of non-Newtonian Casson fluid in a bifurcated channel having stenosis with elastic walls
PublikacjaFluid–structure interaction (FSI) gained a huge attention of scientists and researchers due to its applications in biomedical and mechanical engineering. One of the most important applications of FSI is to study the elastic wall behavior of stenotic arteries. Blood is the suspension of various cells characterized by shear thinning, yield stress, and viscoelastic qualities that can be assessed by using non-Newtonian models. In this...
-
Nutrient transport and acquisition by diatom chains in a moving fluid
PublikacjaThe role of fluid motion in delivery of nutrients to phytoplankton cells is a fundamental question in biological and chemical oceanography. In the study of mass transfer to phytoplankton, diatoms are of particular interest. They are non-motile, are often the most abundant components in aggregates and often form chains, so they are the ones expected to benefit most from enhancement of nutrient flux due to dissipating turbulence....
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublikacjaThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
Maxillary sinus aeration analysis using computational fluid dynamics
PublikacjaThe maxillary sinus aeration using the computational fluid dynamics (CFD) method based on individual adult patients’ computed tomography (CT) scans were analyzed. The analysis was based on CT images of 4 patients: one with normal nose anatomy and three with nasal septal deviation (NSD) and concha bullosa (CB). The CFD simulation was performed using the Reynolds-Average Simulation approach and turbulence closure based on linear...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Analytical ‘Steady-State’-Based Derivation and Clarification of the Courant-Friedrichs-Lewy Condition for Pipe Flow
PublikacjaThis article addresses the problem of choosing the optimal discretization grid for emulating fluid flow through a pipeline. The aggregated basic flow model is linearized near the operating point obtained from the steady state analytic solution of the differential equations under consideration. Based on this model, the relationship between the Courant number (μ) and the stability margin is examined. The numerically set coefficient...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublikacjaFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
A New Approach for the Mitigating of Flow Maldistribution in Parallel Microchannel Heat Sink
PublikacjaThe problem of flow maldistribution is very critical in microchannel heat sinks (MCHS). It induces temperature nonuniformity, which may ultimately lead to the breakdown of associated system. In the present communication, a novel approach for the mitigation of flow maldistribution problem in parallel MCHS has been proposed using variable width microchannels. Numerical simulation of copper made parallel MCHS consisting of 25 channels...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Determination of Mechanical Energy Loss in Steady Flow by Means of Dissipation Power
PublikacjaWhen systems of simple geometry like pipes or regular channels are considered, the mechan- ical energy loss of the fluid flow can be expressed by local and longitudinal empirical energy loss coefficients. However, in the case of large spatially distributed objects, there are no simple approaches to this task. In practice, general recommendations addressing different types of objects are used, but they usually provide very coarse...
-
Modeling and simulation of blood flow under the influence of radioactive materials having slip with MHD and nonlinear mixed convection
PublikacjaRadioactive materials are widely in industry, nuclear plants and medical treatments. Scientists and workers in these fields are mostly exposed to such materials, and adverse effects on blood and temperature profiles are observed. In this regard, objective of the current study is to model and simulate blood based nanofluid with three very important radioactive materials, named as Uranium dioxide (UO2), Thorium dioxide (ThO2) and...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublikacjaThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublikacjaOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...