Filtry
wszystkich: 613
wybranych: 523
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: HYDRAULIC FLOOD ROUTING
-
Compact satellite hydraulic unit
PublikacjaThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Numerical Simulation of Catastrophic Flood: the Case Study of Hypothetical Failure of the Bielkowo Hydro–Power Plant Reservoir
PublikacjaThe numerical modeling of flood wave propagation following the hypo-thetical breaks of the embankments of the Bielkowo hydro–power plant storage reservoir (Kolbudy II Reservoir) on the Radunia River in Poland have been presented. The results of computations were used to estimate the parameters of the flood waves, which are indispensable for the flood zone determination and mapping and then for the flood risk analysis. When estimating...
-
A Revised Approach to Flood Damage Estimation in Flood Risk Maps and Flood Risk Management Plans, Poland
Publikacja -
Flood risk assessment for office and services building Alchemia II at Al. Grunwaldzka 409 in Gdansk.
PublikacjaThe aim of the study is to assess the risk of flood from natural meteorological and hy-drological phenomena, for office and services building Alchemia II in Gdansk at Al. Grun-waldzka 409. The project includes the analysis of potential sources of floods in Gdansk re-garding the Baltic Sea and the Gulf of Gdansk, the Vistula River basin and excessive rainfall and snowmelt waters being a significant element of hydrological processes...
-
The influence of pressure drop on the working volume of a hydraulic motor
PublikacjaReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
Geographic Information System for Flood Hazard Analysis and Early Warning Using Numerical Weather Predictions
PublikacjaFloods are a phenomenon which causes significant losses of lives as well as property damage, which in turn severely impact the local economy. The nature of a flooding has been well researched, and several methods of flood hazard simulation have been established over the last decades. The current legislation in the European Union requires the Member States to create, maintain and update flood risk and hazard maps, as well as identify...
-
ADOPTED ISOCHRONE METHOD IMPROVING SHIP SAFETY IN WEATHER ROUTING WITH EVOLUTIONARY APPROACH
PublikacjaThe paper is focused on adaptation of an isochrone method necessary for application to a weather routing system with evolutionary approach. Authors propose an adaptation of the isochrone method with area partitioning assuring that the route found by the adopted method would not cross land. In result, when applied to a weather routing system with evolutionary approach, this proposal facilitates creation of initial population, resulting...
-
COMPUTER ANALYSIS OF HYDRAULIC CONDITIONS IN A SANITARY CHAMBER
PublikacjaThis paper presents analysis of hydraulic conditions of sewage flow down the slipway (ramp) in the collecting sanitary chamber connecting 3 collectors on the inlet: ⌀600, ⌀800 and ⌀1400 and one on the outlet ⌀1600 mm, with a maximum difference of elevation 5 m. The mathematical model has been made and hydraulic calculations were carried out in steady flow conditions. Then wastewater surface elevation, energy grade line elevation,...
-
Influence of Self-Similar Traffic Type on Performance of QoS Routing Algorithms
PublikacjaProviding a Quality of Services (QoS) into current telecommunication networks based on packet technology is a big challenge nowadays. Network operators have to support a number of new services like voice or video which generate new type of traffic. This traffic serviced with QoS in consequence requires access to appropriate network resources. Additionally, new traffic type is mixed with older one, like best-effort. Analysis of...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublikacjaThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Methods for physical impairment constrained routing with selected protection in all-optical networks
PublikacjaIn this paper, we investigate the problem of survivable all-optical routing in WDM networks with physical impairments. One of the recent key issues in survivable optical network design refers to maximization of the ratio of routeable demands while keeping the overall network cost low. In WDM networks, this goal can be achieved by routing as many demands in all-optical way as possible. Based on the latest technical trends driven...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublikacjaDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublikacjaA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
An advanced tool integrating failure and sensitivity analysis into novel modeling of the stormwater flood volume
PublikacjaAn innovative tool for modeling the specific flood volume was presented that can be applied to assess the need for stormwater network modernization as well as for advanced flood risk assessment. Field measurements for a catchment area in Kielce, Poland, were used to apply the model and demonstrate its usefulness. This model extends the capability of recently developed statistical and machine learning hydrodynamic models developed...
-
Flood problems in Gdańsk .
PublikacjaOmówiono źródła zagrożeń powodziowych Gdańska. Przedstawiono przyczyny, przebieg i skutki powodzi w lipcu 2001 r. Oceniono przygotowanie systemu cieków do przepuszczania wielkich wód.
-
Change in Heavy Metals Concentrations in Sediments Deposited in Retention Tanks in a Stream after a Flood
PublikacjaOur paper presents the results of heavy metal (HM) (Zn, Cu, Pb, Cd) content in bottom sediments from retention tanks along Oliwa Stream in Gdańsk, Poland, before a flood (BF) and after a flood (AF) 14-15 July 2016. The flood had a huge impact on the quality of bottom sediments and their displacement. The concentrations of HM differed significantly for research series conducted 3 months BF and 8 months AF. The concentration of Cu...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
New generation of the satellite hydraulic pumps
PublikacjaHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
Investigation method and mathematical model of pressure losses in hydraulic rotary motor
PublikacjaTis paper presents a way of determining the coefcient k of the pressure losses Δp (fow drag) in internal ducts 8 Mp of SWSB-63 hydraulic motor. Te coefcient is determined at a fow rate equal to the theoretical capacity Q of the Pt pump feeding the motor , the losses are related to the nominal pressure p in the hydraulic system. Te investigations n followed a model of energy performance of hydraulic rotary motor, proposed by...
-
Multipath routing for quality of service differentiation and network capacity optimization in broadband low-earth orbit systems
PublikacjaThis paper shows the importance of employing multiple different paths for routing in Inter-Satellite Link (ISL) networks in broadband Low-Earth Orbit (LEO) satellite systems. A theoretical analysis is presented and a routing concept is proposed to demonstrate three facts that make multipath routing especially important in broadband LEO networks: (1) differences in the propagation delays have a much greater impact on end-to-end...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublikacjaThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publikacjahydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
Hydraulic conductivity of a biopolymer treated sand
PublikacjaThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
GIS-based hydrodynamic modeling for urban flood mitigation in fast-growing regions: a case study of Erbil, Kurdistan Region of Iraq
PublikacjaFloods threaten urban infrastructure, especially in residential neighborhoods and fast-growing regions. Flood hydrodynamic modeling helps identify flood-prone locations and improve mitigation plans' resilience. Urban floods pose special issues due to changing land cover and a lack of raw data. Using a GIS-based modeling interface, input files for the hydrodynamic model were developed. The physical basin's properties were identified...
-
Integrated model for the fast assessment of flood volume: Modelling – management, uncertainty and sensitivity analysis
PublikacjaThe specific flood volume is an important criterion for assessing the performance of sewage networks. It has been shown that its value is greatly influenced by the layout of the sewers in the catchment area, which is usually expressed by a fractal dimension. Currently, only mechanistic models (such as SWMM) enable the determination of the impact of the layout of the sewers on flooding volume, but they require additional and robust...
-
Power balance in hydraulic satellite motors supplied with oil and HFA-E emulsion
PublikacjaMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motors with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motors.
-
Mapping of Flood-Prone Areas Utilizing GIS Techniques and Remote Sensing: A Case Study of Duhok, Kurdistan Region of Iraq
PublikacjaOne of the most common types of natural disaster, floods can happen anywhere on Earth, except in the polar regions. The severity of the damage caused by flooding can be reduced by putting proper management and protocols into place. Using remote sensing and a geospatial methodology, this study attempts to identify flood-vulnerable areas of the central district of Duhok, Iraq. The analytical hierarchy process (AHP) technique was...
-
Flood Classification in a Natural Wetland for Early Spring Conditions Using Various Polarimetric SAR Methods
PublikacjaAbstract--- One of the major limitations of remote sensing flood detection is the presence of vegetation. Our study focuses on a flood classification using Radarsat-2 Quad-Pol data in a natural floodplain during leafless, dry vegetation (early spring) state. We conducted a supervised classification of a data set composed of nine polarimetric decompositions and Shannon entropy followed by the predictors' importance estimation to...
-
Sailing Vessel Routing Considering Safety Zone and Penalty Time for Altering Course
PublikacjaIn this paper we introduce new model for simulation sea vessel routing. Besides a vessel types (polar diagram) and weather forecast, travel security and the number of maneuvers are considered. Based on these data both the minimal travelling costs and the minimal processing time are found for different vessels and different routes. To test our model the applications SailingAssistance wad improved. The obtained results shows that...
-
Collision‐Aware Routing Using Multi‐Objective Seagull Optimization Algorithm for WSN‐Based IoT
PublikacjaIn recent trends, wireless sensor networks (WSNs) have become popular because of their cost, simple structure, reliability, and developments in the communication field. The Internet of Things (IoT) refers to the interconnection of everyday objects and sharing of information through the Internet. Congestion in networks leads to transmission delays and packet loss and causes wastage of time and energy on recovery. The routing protocols...
-
Routing Method for Interplanetary Satellite Communication in IoT Networks Based on IPv6
PublikacjaThe matter of interplanetary network (IPN) connection is a complex and sophisticated topic. Space missions are aimed inter alia at studying the outer planets of our solar system. Data transmission itself, as well as receiving data from satellites located on the borders of the solar system, was only possible thanks to the use of powerful deep space network (DSN) receivers, located in various places on the surface of the Earth. In...
-
Losses and power balance in hydraulic satellite motor supplied with oil and HFA-E emulsion
PublikacjaMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motor with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motor. The research of satellite motor has been conducted...
-
Evaluation of losses in a hydraulic motor based on the SWSB - 63 motor tests
PublikacjaIn this paper are compared two models of energy losses: that suggested by Prof. Paszota,Z. in monograph "Energy losses in the hydraulic displacement motors - definitions and relations serving the evaluation of the efficiency of hydrostatic drive" [18] and that ofProf. Balawender, A. in "Energy analysis and methodology of testing of low-speed hydraulic motors" [1]. By using the data obtained from the tests of SWSB-63 hydraulic motors...
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublikacjaHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublikacjaA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Terminal charging scheduling of battery electric buses based on vehicle routing problem
PublikacjaElectric buses are considered to be a viable solution for reducing emission in dense urban areas. However, the greater charging time is a huge challenge for operators. In this paper, charging scheduling method was elaborated based on vehicle routing problem using mixed-integer linear programming model. The main novelty of the paper is the combination of modelling aspect, namely flexible turn sequence and heterogeneous shared charging...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublikacjaIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
Ship weather routing optimization with dynamic constraints based on reliable synchronous roll prediction
PublikacjaShip routing process taking into account weather conditions is a constrained multi-objective optimization problem and it should consider various optimization criteria and constraints. Formulation of a stability-related, dynamic route optimization constraint is presented in this paper. One of the key objectives of a cross ocean sailing is finding a compromise between ship safety and economics of operation. This compromise should...
-
LLA : A New Anypath Routing Scheme Providing Long Path Lifetime in VANETs
PublikacjaVehicular ad-hoc networks (VANETs) are a promising solution to improve the road traffic safety, reduce the environmental pollution, or simply provide the on-board infotainment services. However, these actions are often not possible due to high mobility of vehicles causing frequent failures of VANET links. In this paper, we focus on anypath routing to improve the reliability of multihop VANET communications. In particular, the paper...
-
Path Coloring and Routing in Graphs.
PublikacjaW rozdziale omówione zostały problemy kolorowania ścieżek i routingu w grafach. Podano podstawowe definicje związane z tymi problemami, znane wyniki wraz z dyskusją złożoności obliczeniowej dla grafów ogólnych i dla kilku podstawowych klas grafów oraz zastosowania.
-
Optimal routing in a transportation network
Publikacja -
The influence of water and mineral oil on volumetric losses in a hydraulic motor
PublikacjaIn this paper volumetric losses in hydraulic motor supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and comparison. The experimental tests were conducted using an innovative hydraulic satellite motor, that is dedicated to work with different liquid, including water. The sources of leaks in this motor are characterized and described also. On this...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Reliable routing and resource allocation scheme for hybrid RF/FSO networks
PublikacjaSignificant success of wireless networks in the last decade has changed the paradigms of communication networks design. In particular, the growing interest in wireless mesh networks (WMNs) is observed. WMNs offer an attractive alternative to conventional cable infrastructures, especially in urban areas, where the cost of new installations is almost prohibitive. Unfortunately, the performance of WMNs is often limited by the cluttered...
-
Weather Routing System Architecture Using Onboard Data Collection and Route Optimisation
PublikacjaThis paper describes the architecture of a weather routing system consisting of two key elements: onboard monitoring and route optimiser sub-systems. The former is responsible for collecting various onboard measurements, such as current ship position or ship motion variables. These data, when gathered and processed, are then used for fine-tuning a ship model. The model, together with weather forecasts, is utilised by a multi-objective...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublikacjaDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublikacjaThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
-
Flood zones - a risk for the urban areas
PublikacjaPrzedstawiono studium dotyczące wyznaczenia stref zagrożenia powodziowego dla miasta Warszawy wskutek wezbrań rzeki Wisły. Do oszacowania zasięgu stref wykorzystano matematyczny model ustalonego przepływu wolnozmiennego oraz numeryczny model terenu doliny rzeki. Do zobrazowania uzyskanych wyników zastosowano system GIS. Na podstawie uzyskanych wyników zidentyfikowano obszary miasta Warszawy narażone na ewentualną powódź oraz odcinki...