Filtry
wszystkich: 189
wybranych: 177
Wyniki wyszukiwania dla: MARINE INTERNAL COMBUSTION ENGINE
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublikacjaThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublikacjaA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Modeling of Surface Roughness in Honing Processes by UsingFuzzy Artificial Neural Networks
PublikacjaHoning processes are abrasive machining processes which are commonly employed to improve the surface of manufactured parts such as hydraulic or combustion engine cylinders. These processes can be employed to obtain a cross-hatched pattern on the internal surfaces of cylinders. In this present study, fuzzy artificial neural networks are employed for modeling surface roughness parameters obtained in finishing honing operations. As...
-
Battery Technologies in Electric Vehicles: Improvements in Electric Battery Packs
PublikacjaRestrictions on fossil fuels and related environmental pollution issues motivate many organizations and countries to set their focus on electric vehicles (EVs) rather than conventional internal combustion engine vehicles [1], [2]. EVs require an energy storage system to store converted electric power in another form of energy and then reconvert the stored energy to electric power whenever it is required. The energy stored can be...
-
THE VIBRATION BASED DIAGNOSTICS OF SHIP PROPULSION SYSTEMS
PublikacjaThe article has been worked out on the basis of the report devoted to the conducted diagnostic investigations of the ship main propulsion unit’s mechanical system. Gdansk University of Technology has been ordered with such investigations by the repair Shipyard carrying out the ship’s overhaul. Diagnostic tests involved measurements and analyses of the vibration signals generated in selected constructional kinematic pairs of the...
-
DESIGN OF THE DUAL CONSTELLATION GPS/GALILEO MOBILE DEVICE FOR IMPROVING NAVIGATION OF THE VISUALLY IMPAIRED IN AN URBAN AREA, POLISH MARITIME RESEARCH
PublikacjaThe article discusses damages of essential tribological associations in crankshaft and piston systems of large power two-stroke engines used as main engines, which take place during transport tasks performed by those ships. Difficulties are named which make preventing those damages impossible, despite the fact that the technical state of engines of this type is identified with the aid of complex diagnostic systems making use of...
-
Regeneration of marine engine valves using laser surfacing
PublikacjaThis article presents an analysis of the applicability of laser surfacing of the exhaust valve face of a marine diesel engine using cobalt-based powder. After preparation by machining, the selected valves were subjected to laser surfacing using a high-power ROFIN DL020 laser. The EuTroLoy 16012 powder was used in the surfacing process. One of the valves was cut and subjected to metallographic examination and hardness measurements,...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublikacjaThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublikacjaThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
Fault detection in the marine engine using a support vector data description method
PublikacjaFast detection and correct diagnosis of any engine condition changes are essential elements of safety andenvironmental protection. Many diagnostic algorithms significantly improve the detection of malfunctions.Studies on diagnostic methods are rarely reported and even less implemented in the marine engine industry.To fill this gap, this paper presents the Support Vector Data Description (SVDD) method as applied to thefault detection...
-
Failure analysis of the exhaust valve face in diesel marine engine
PublikacjaThe exhaust valve from marine diesel engine which was damaged after 2000 hours of service was investigated. In order to prolong the service time the valve face was cladded with cobalt base alloy using laser technique. After failure microstructural and chemical analyses reviled that cladding process was conducted improperly. The chemical composition of the clad layer was far from the designed one and what more completely inhomogeneous....
-
Possibilities of the performance improvement of the aero- and marine propulsion units equipped with combustion piston engines
PublikacjaWithin the paper there have been presented the authors' opinions concerning possibilities and needs of the performance optimization of the aero- and marine units powered by piston engines both of ''classic'' and contemporary construction. There have been also discussed the reserves contained within combustion piston engines which enable its performance improvement (the power and specific fuel consumption) as well as the fulfillment...
-
TEST METHOD FOR DETERMINING THE CHEMICAL EMISSIONS OF A MARINE DIESEL ENGINE EXHAUST IN OPERATION
PublikacjaThe article briefly describes the problem of air pollution caused by sea-going ships and the resulting restrictions on the emission of toxic and harmful chemical compounds in the exhaust of marine engines, introduced by the International Maritime Organization (IMO) under the International Convention for the Prevention of Sea Pollution from Ships (MARPOL 73/78). Such emissions provide a significant metrological problem, not only...
-
Evaluation of working spaces' technical condition of marine diesel engine on the basis of operation research
PublikacjaThe paper presents the method of evaluation of the technical state of working spaces of a marine diesel engine at the reduced control susceptibility. The method foresees making diagnosis on the basis of the measurements of exhaust gas pressure in the channels connecting engine cylinders with turbocharger's turbine. In the beginning of the article the research objects are characterized i.e. ZVIEZDA main engine of M401 type and the...
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublikacjaThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
Conception of valuation of combustion engine operation
PublikacjaW artykule zaproponowano interpretację wartościującą działania, które jest przyrównane do wielkości fizycznej o jednostce miary zwanej dżulosekundą, podobnie jak przedstawione w mechanice klasycznej działania Hamiltona i Maupertiusa. Działanie w tym ujęciu rozpatrywane jest także w mechanice kwantowej, w odniesieniu do żródła promieniowania elektromagnetycznego ciała, którego działanie charakteryzuje stała Planca. Przedstawiono...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublikacjaWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Performance and Emission Modelling and Simulation of Marine Diesel Engines using Publicly Available Engine Data
PublikacjaTo analyse the behaviour of marine diesel engines in unsteady states for different purposes, for example to determine the fuel consumption or emissions level, to adjust the control strategy, to manage the maintenance, etc., a goal-based mathematical model that can be easily implemented for simulation is necessary. Such a model usually requires a wide range of operating data, measured on a test stand. This is a time-consuming process...
-
Utilization of the zero unitarization method for the building of a ranking for diagnostic marine engine parameters
PublikacjaChanging some of the parameters of the engine structure affects the emission of harmful components in the exhaust gases This primarily concerns damage in the cargo exchange system as well as in the fuel system and engine boost system. Changes in emissions of harmful compounds are often ambiguous, depending largely on the parameters that shape the combustion process. An additional problem is that often simple but undesired interactions...
-
The Effect of Oxygenated Diesel-N-Butanol Fuel Blends on Combustion, Performance, and Exhaust Emissions of a Turbocharged CRDI Diesel Engine
PublikacjaThe article deals with the effects made by using various n-butanol-diesel fuel blends on the combustion history, engine performance and exhaust emissions of a turbocharged four-stroke, four-cylinder, CRDI 1154HP (85 kW) diesel engine. At first, load characteristics were taken when running an engine with normal diesel fuel (DF) to have ‘baseline’ parameters at the two ranges of speed of 1800 and 2500 rpm. Four a fossil diesel (class...
-
THE METHOD OF ENERGY-EFFICIENCY INVESTIGATIONS OF THE NEWLY PRODUCED MARINE FUELS THROUGH AN APPLICATION OF THE LABORATORY DIESEL ENGINE
PublikacjaThe article deals with one of the scientific issue solved within frames of the research project financed by Voivodeship Fund for Environmental Protection and Water Management in Gdansk, namely, in particular, the method of energy investigations of the self-ignition engine in conditions of its supply with a non-standard (modified) marine fuel. The representative results of engine tests worked out on the especially built laboratory...
-
Impacts of Using Exhaust Gas Recirculation and Various Amount of Dimethyl Ether Premixed Ratios on Combustion and Emissions on a Dual-Fuel Compression Ignition Engine
PublikacjaIn the presented research, the authors dealt with the specific properties of the combustion process of dimethyl ether (DME) in a combustion car (Volkswagen Golf IV) engine AJM 1.9 TDI PDE made by Volkswagen factory. Dimethyl ether is an alternative fuel produced most often from natural gas, which can be used in compression ignition engines as a single fuel or co-burned with diesel oil. This work describes the impacts of using exhaust...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublikacjaThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
HEALTH MONITORING OF A COMPRESSION IGNITION ENGINE FED WITH DIFFERENT LOW-SULPHUR MARINE FUELS BY ENDOSCOPIC IMAGE PROCESSING AND ANALYSIS
PublikacjaThis article characterises the methodology for the endoscopic testing of a laboratory diesel engine used for testing marine fuels. The ‘Shadow’ measurement method used in the XLG3 type EVEREST digital endoscope, for quantitative and qualitative identification of detected surface defects, was approximated. Representative endoscopic images of the elements limiting the working space of the research engine are demonstrated, having...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
TEST FOR ASSESSING THE ENERGY EFFICIENCY OF VEHICLES WITH INTERNAL COMBUSTION ENGINES
PublikacjaThe most popular method for assessing the energy efficiency of vehicles is to compare the fuel consumption achieved in the conditions of selected approval test. Operating conditions are defined using the speed profiles, usually for only two categories: urban and extra-urban driving. Assessing the energy efficiency of vehicles should be performed using a more detailed classification of conditions. Presented results of comparison...
-
Geothermal heating plant with a combustion engine heat pump.
PublikacjaPrzedstawiono koncepcję ciepłowni geotermalnej zagospodarowującej zasoby energii zawarte w nisko i średniotemperaturowej wodzie termalnej. W tym celu zaproponowano zastosowanie pompy grzejnej napędzanej silnikiem spalinowym.
-
MODELLING OF TOXIC COMPOUNDS EMISSION IN MARINE DIESEL ENGINE DURING TRANSIENT STATES AT VARIABLE PRESSURE OF FUEL INJECTION
PublikacjaTransient states are an important part of the spectrum of engine loads, especially the traction engines. In the case of marine diesel engines, transient states are of particular importance in reducing the analysis of motion units for special areas and maneuvering in port, the participation of transient states in the load spectrum significantly increases, also, the emission of toxic compounds from this period increases proportionally....
-
Influence of the abrasive grain trajectory on the machining of thin-walled cylinder liners of internal combustion engines with variable kinematics of honing
PublikacjaGładzenie ze zmienną kinematyką posiada szereg zalet w porówna-niu do tradycyjnego gładzenia [1-19], takie jak: mniejsze zużycie na-rzędzia [12, 13], niższa temperatura obróbki [13], lepsza jakość po-wierzchni [12, 13] oraz mniejsza odchyłka walcowości [13]. W arty-kule omówiono zalety zmiennej kinematyki gładzenia. Można zało-żyć, że gładzenia ze zmienną kinematyką „VH” zostanie wdrożone wkrótce w przemyśle, np. w produkcji elementów...
-
Evaluation of the influence of the opening pressure of a marine Diesel engine injector on the results of numerical simulation of the working cycle and their comparison with the results of the laboratory experiment
PublikacjaThe article presents the results of a numerical simulation of the working process carried out in a diesel engine. In the applied utility program DIESEL-RK, the laboratory engine Farymann Diesel type D10 was implemented. A selected inoperability of its functional fuel supply system - reduced opening pressure of the injector pinj - was introduced. The values of adequate diagnostic parameters were determined: working gas temperature...
-
Simulation of ammonia combustion in dual-fuel compression-ignition engine
Publikacja -
Four-stroke engine with central located, dyvided combustion chamber
PublikacjaW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne nowoczesnego czterosuwowego silnika spalinowego z centralnie umieszczoną, dzieloną komorą spalania. Rozwiązanie takie umożliwia znacznie lepsze wykorzystanie ciepła, co oznacza wyższą sprawność i mniejsze zużycie paliwa oraz niższą emisję szkodliwych gazów takich, jak tlenki azotu (NO2), węglowodory (HC) i dwutlenek węgla (CO2). Silnik może pracować na paliwo płynne...
-
A semi-Markov model of fuel combustion process in a Diesel engine
PublikacjaW artykule przedstawiono czterostanowy model procesu spalania w przestrzeniach roboczych (cylindrach) silników o zapłonie samoczynnym w formie procesu semimarkowskiego, dyskretnego w stanach i ciągłego w czasie. Wartościami tego procesu są stany odpowiadające powszechnie akceptowanym rodzajom spalania w tego rodzaju silnikach a mianowicie takie stany procesu jak: spalanie pełne (całkowite i zupełne), spalanie niezupełne, spalanie...
-
Reliability model of two-shaft turbine combustion engine with heat regenerator
PublikacjaW artykule przedstawiono możliwość zastosowania teorii procesów semimarkowskich do opisu niezawodności turbinowego silnika spalinowego. Opracowano model niezawodnościowy w formie siedmiostanowego procesu semimarkowskiego, umożliwiający określenie prawdopodobieństw przebywania silnika w stanie zdatności oraz wyróżnionych stanach niezdatności.
-
Model of process of wear sidle bearings of self ignition combustion engine
PublikacjaW artykule została podjęta próba przeanalizowania praktycznej przydatności modelu procesu zużycia głównych łożysk ślizgowych silnika spalinowego o ZS, opisującego zmienną szybkość ich zużycia. Analizie został poddany problem częstych zatrzymań i rozruchów silnika, gdyż z badań statystycznych wynika, że w tym czasie występuje największe zużycie łożysk ślizgowych.
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublikacjaIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
Identification analysis of dynamic changes in the composition of biogas and their impact on the operation of internal combustion engines
PublikacjaW pracy zamieszczono wyniki badań składu biogazu pozyskiwanego na komunalnym wysypisku śmieci. Pozyskiwany biogaz jest wykorzystywany do zasilania biogazowych zespołów prądotwórczych wyposażonych w silniki o zapłonie iskrowym dostosowanych do zasilania tym paliwem. Pozyskiwany biogaz powstaje w sposób naturalny w procesie beztlenowej fermentacji zachodzącej przez ok. 20 lat, w organicznej części pryzmy odpadów składowanych na wysypisku...
-
Planning of structure and range of preventive maintenance of marine diesel engine
PublikacjaPrzedstawiono sposób wyznaczania zasobów godzin pracy elementów złożonego obiektu technicznego na przykładzie okrętowego silnika spalinowego oraz planowania struktury i zakresu jego obsługi profilaktycznej.
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
Evaluation of methods for determining the combustion ignition delay in a diesel engine powered by liquid biofuel
Publikacja -
Dissipated energy minimization in a combustion engine Mount system by position dependent damping coefficients
PublikacjaPraca opisuje rozważania na temat możliwości tłumienia drgań spalinowego silnika czterosuwowego. Do modelowania wykorzystano zasady dynamiki układów wielomasowych. Przedstawiono krótki opis wspomnianego sposobu modelowani. Zbudowano model numeryczny silnika. Model poddano analizie numerycznej. Podczas analizy dynamiki układu skoncentrowano się na elementach tłumiących drgania, obecnych w zawieszeniu silnika oraz na analizie wpływu...
-
INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION
Publikacja -
Fault Tree Analysis and Failure Diagnosis of Marine Diesel Engine Turbocharger System
Publikacja -
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublikacjaThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Possible efficiency increasing of ship propulsion and marine power plant with the system combined of marine diesel engine, gas turbine and steam turbine
PublikacjaW rozdziale przedstawiono koncepcję układu kombinowanego okrętowego lub morskiej pływającej elektrowni dużej mocy złożonego z silnika głównego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika głównego tłokowego. Rozpatrywano możliwości zastosowania takich układów w układach okrętowych z punktu widzenia sprawnościowego. Podano możliwości...
-
ANN based evaluation of the NOx concentration in the exhaust gas of a marine two-stroke diesel engine
Publikacja -
The system combined of low-speed marine diesel engine and steam turbine in ship propulsion applications
PublikacjaPrzedstawiono koncepcje okrętowego układu kombinowanego silnik wolnoobrotowy tłokowy- turbina parowa, wykorzystującego ciepło zawarte w spalinach wylotowych.Porównano układ kombinowany dużej mocy dla dwóch silników tłokowych porównywalnych mocy z punktu widzenia termodynamicznego.
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Analysis of balancing of six-cylinder in-line two-stroke internal combustion engines = Analiza wyrównoważenia silników rzędowych dwusuwowych sześciocylindrowych
PublikacjaW pracy wyprowadzono proste zależności opisujące przebieg momentu od sił bezwładności pierwszego i drugiego rzędu dla wszystkich 60 wariantów wałów korbowych w silniku 6-cylindrowym 2-suwowym rzędowym. Dokonano analizy i porównania poszczególnych wariantów z punktu widzenia momentów wypadkowych od sił bezwładności pierwszego i drugiego rzędu. Porównania dokonano dla dwóch wartości parametru mechanizmu korbowego 0,3 i 0,5.