Wyszukiwarka
Filtry
wszystkich: 203
wybranych: 199
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: CFD APPLICATION
-
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublikacjaThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Design Equation for Stirring Fluid by a Stream Pump in a Circulating Tank
PublikacjaA circulating tank is a very useful theoretical scheme for many fluid-flow objects in several branches of engineering. The motion of the fluid in such objects can be induced in different ways. A stream pump provides an especially interesting possibility; however, the quantitative description of such devices shows some shortcomings. Such a device is analogous to a jet pump, thus has similar advantages (simplicity of construction,...
-
Influence of Bingham fluid viscosity on energy performances of a vortex chamber pump
PublikacjaOne of the problems in the development of coal-water technologies is the use of reliable and long-lasting pumps. To date, classic pumps, due to the use of mechanical moving parts and seals, are subject to rapid abrasive wear. The solution to this problem can lie in the creation of new vortex chamber pumps developed by the authors. They are highly reliable, simple in design and have no moving parts. The object of this paper consists...
-
Negative CO2 Emission Gas Power Plant As Technology for Utilization of Sewage Sludge, Production of Electrical Energy, and CO2 Capture - Case of Chamber Under Transpiration Cooling
PublikacjaThis work focuses on the concept developed in the nCO2PP project, which aims to demonstrate a technology that allows to achieve negative CO2 emissions through Carbon Capture and Storage (CCS) applied to sewage sludge. A feedstock is first gasified, then the resulting syngas is burned in a semi-closed oxy-fuel gas turbine with pure oxygen and water, using the advantages of oxy-combustion, to ease the capture of CO2 in the resulting...
-
Why is TASK Quarterly a Significant Journal to Publish Your Article? —A Bibliometric Analysis of a Scientific and Technical Journal
PublikacjaA bibliometric analysis of TASK Quarterly in the years 1997-2021 in terms of various bibliometric indicators was performed to celebrate the 25th anniversary of the publication of the first issue of the journal. The number of publications and citations increased over the mentioned span of years. The leading countries in terms of the greatest number of papers published in TASK Quarterly are Poland, Italy, Germany, Ukraine, USA and...
-
„Eulerian – Eulerian” versus ,,Eulerian –Lagrangean” models of condensation
PublikacjaLiquid phase in the flowing vapor through stages of the steam turbine is the cause of a lot of failures. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current. The formation of drops of condensate under conditions other than nominal operation of turbine is a process still unknown. Engineers and designers involved in the development of power station machines...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublikacjaThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Constrained aerodynamic shape optimization using neural networks and sequential sampling
PublikacjaAerodynamic shape optimization (ASO) involves computational fluid dynamics (CFD)-based search for an optimal aerodynamic shape such as airfoils and wings. Gradient-based optimization (GBO) with adjoints can be used efficiently to solve ASO problems with many design variables, but problems with many constraints can still be challenging. The recently created efficient global optimization algorithm with neural network (NN)-based prediction...
-
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
PublikacjaThis article focuses principally on the comparison baseline and the optimized flow efficiency of the final stage of an axial turbine operating on a gas–steam mixture by applying a hybrid Nelder– Mead and the particle swarm optimization method. Optimization algorithms are combined with CFD calculations to determine the flowpaths and thermodynamic parameters. The working fluid in this study is a mixture of steam and gas produced...
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublikacjaThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Real-time simulator of agricultural biogas plant
PublikacjaThis article presents a real-time simulator of an agricultural biogas plant. The project contains biogas and biomass circuits simulation, as well as heating circuit simulation with a complete control system and visualization interface of the whole process. The software tool used to simulate the plant work is CFD (Computational Fluid Dynamics), which enables a user to create and test simulation objects based on fundamental physical...
-
Methods of Determining Pressure Drop in Internal Channels of a Hydraulic Motor
PublikacjaIn this paper, new methods for determining the pressure drop in internal channels of a hydraulic motor are proposed and described. Mathematical models of pressure losses in internal channels have also been described. Experimental tests of the satellite motor were carried out according to one of the proposed methods. The tests were carried out for two liquids, i.e., water and mineral oil. Experimental studies have shown that at...
-
The Motion Analysis of Attacus Atlas Rigid Wing
PublikacjaThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
INNOVATIVE THERMODYNAMICAL CYCLES BASED ON ENHANCEMENT MASS, MOMENTUM, ENTROPY AND ELECTRICITY TRANSPORT DUE TO SLIP, MOBILITY, TRANSPIRATION, ENTROPY AND ELECTRIC JUMPS AS WELL AS OTHER NANO-FLOWS PHENOMENA
PublikacjaIn our work, a further development of the authors model of thermo-chemical flow of fuel, air, oxygen, steam water, species, ionic and electron currents within nano channels and nano-structures of novel devices is presented. Different transport enhancement models are taken into account -among them the most important are: the velocity slip connected with complex external friction, the Darcy mobility and the Reynolds transpiration....
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston pump
PublikacjaA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston hydraulic pump
PublikacjaA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublikacjaA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublikacjaIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
Deformable model of a butterfly in motion on the example of Attacus atlas
PublikacjaInsect wings can undergo significant chordwise (camber) as well as spanwise (twist) deformation during flapping flight but the effect of these deformations is not well understood. The shape and size of butterfly wings leads to particularly large wing deformations, making them an ideal test case for investigation of these effects. High-speed videogrammetry was used to capture the wing kinematics and deformations. The movements of...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublikacjaThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Wpływ konstrukcji przestrzeni międzyklockowej na charakterystyki wzdłużnego łożyska ślizgowego
PublikacjaSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania dużych wzdłużnych łożysk ślizgowych. W chwili obecnej wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności łożyska, które następuje m. in. po obniżeniu temperatury maksymalnej w filmie smarowym, co można uzyskać poprzez skuteczne dostarczanie zimnego oleju zasilającego wprost do strefy wlotowej filmu olejowego. Jednym z takich rozwiązań konstrukcyjnych,...
-
Design and investigations of a micro-turbine flow part
Publikacja-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublikacjaThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublikacjaSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
Modeling of entrained flow steam gasification of sewage sludge
PublikacjaProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublikacjaAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
DETERMINATION OF SEAKEEPING PERFORMANCE FOR A CASE STUDY VESSEL BY THE STRIP THEORY METHOD
PublikacjaThe increase of seakeeping performance is of particular importance for car and passenger ferries, service ships in the gas and oil extraction industry and offshore wind power farm industry, as well as for special purpose ships (including military applications). In the water areas of the Baltic Sea, North Sea, and Mediterranean Sea, which are characterised by a short and steep wave, the hull shape has a substantial impact on the...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
A novel DEM-based pore-scale thermal-hydro-mechanical model for fractured non-saturated porous materials
PublikacjaDo propagacji pęknięć wykorzystano nowy oparty na DEM, termiczno-hydromechaniczny model dwufazowego przepływu płynu w skali porów rozszerzony o wymianę ciepła w nienasyconych materiałach porowatych o małej porowatości. Wykonano obliczenia numeryczne dla kohezyjnych próbek ziarnistych przy użyciu DEM w pełni sprzężonego z CFD (opartego na sieci przepływu płynu) i wymianą ciepła, który zintegrował mechanikę dyskretną z mechaniką...
-
Wpływ profilu misji na możliwości operacyjne pojazdu podwodnego
PublikacjaArtykuł powstał na bazie doświadczeń wynikających z wieloletniej współpracy z Marynarką Wojenną RP w zakresie systemów walki przeciwminowej opartych na pojazdach podwodnych oraz projektów naukowo-badawczych dotyczących tego rodzaju pojazdów. Celem podjęcia tematu było stworzenie bazy wiedzy do określania wytycznych dla projektowania i dobierania odpowiednich pojazdów podwodnych do przewidywanych profili misji bojowych uwzględniając...
-
Review of Selected Methods for Prediction of Added Resistance in Following Waves
PublikacjaThe added resistance in waves is a mean value of non-linear, second order reaction of a ship to incoming waves. In the beginning of the 20th century, the experimental methods for investigation of ship hydrodynamics at model scale were developed. They allowed the evaluation of added resistance by measurements in irregular waves (directly) or by measurements in regular waves (in-direct method). The main goal was to find more precise...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublikacjaImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublikacjaAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
High-speed multi-stage gas-steam turbine with flow bleeding in a novel thermodynamic cycle for decarbonizing power generation
PublikacjaIn the global pursuit of sustainable energy and reduced carbon footprints, advances in power generation techniques play a crucial role, not only in meeting the ever-increasing energy demands but also in ensuring that environmental standards are maintained and that the health of our planet is prioritized for future generations. In the ongoing quest for sustainable energy solutions, novel high-speed multi-stage gas-steam turbine...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Analiza porównawcza metod obliczeniowych stopnia turbinowego
PublikacjaRozwój technologii komputerowych i ciągły wzrost dostępności do odpowiednich zasobów mocy obliczeniowej spowodował popularyzację obliczeń numerycznych. Aktualnie korzysta się na szeroką skalę z numerycznej mechaniki płynów, czyli tak zwanych obliczeń CFD. Właściwie przygotowane modele obliczeniowe pozwalają uzyskać bardzo dokładne wyniki na podstawie przeprowadzonych symulacji trójwymiarowych. Odpowiednio skorelowana symulacja...
-
Gasification of Densified Biomass (DB) and Municipal Solid Wastes (MSW) Using HTA/SG Technology
PublikacjaThe necessity of economical and rational use of natural energy sources caused a rapid development of research on the possibilities of using non‐conventional energy resources. Taking the above into account, a new technological process of thermochemical conversion of biomass and communal waste, commonly known as High Temperature Air/Steam Gasification (HTA/SG) and Multi‐Staged Enthalpy Extraction Technology (HTAG‐MEET), was developed....
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Analiza obciążalności prądowej długotrwałej przewodów elektroenergetycznych z wykorzystaniem zaawansowanych metod numerycznych
PublikacjaNiniejsza rozprawa doktorska przedstawia analizę obciążalności prądowej długotrwałej przewodów elektroenergetycznych na przykładzie linii kablowej niskiego napięcia YKY 35 mm2. Analizę obciążalności przeprowadzono w programie ANSYS Fluent, wykorzystującym numeryczną mechanikę płynów (ang. Computional Fluid Dynamics, CFD). W analizach obciążalności prądowej długotrwałej przewodów (kabli) elektroenergetycznych uwzględniono następujące...
-
Mechanizm odparowania kropel kondensatu w strefie fali uderzeniowej
PublikacjaSpontaniczna kondensacja pary, zachodząca dla dobrze zaprojektowanych turbin w obrębie ostatniego stopnia części niskoprężnej, jest nierównowagowym przejściem fazowym indukowanym naprężeniowo. Na pierwszy rzut oka wydaje się, że wymiana ciepła, jako taka ma pomijalny udział w mechanizmie napędzającym przemianę. Jednak, jak pokazały prace Bilickiego i Kestina, nierównowaga termodynamiczna uruchamia zjawiska „szybkiej relaksacji”...
-
Modelowanie matematyczne zjawisk transportu zanieczyszczeń i procesów technologicznych w wybranych reaktorach oczyszczalni ścieków
PublikacjaW pracy opisane zostały wyniki wykonanych przez autora badań dotyczących modelowania adwekcyjno-dyspersyjnego przepływu zanieczyszczeń podlegających reakcjom, na przykładzie reaktorów z osadem czynnym, powszechnie stosowanych w stopniach biologicznych na oczyszczalniach ścieków komunalnych. Analizie poddano możliwości stosowania modeli mechanistycznych ASM (Activated Sludge Model) w połączeniu z równaniami różniczkowymi cząstkowymi...
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublikacjaAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...