Filtry
wszystkich: 475
wybranych: 471
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: MOLECULAR MECHANICS
-
New kinematic systems in single-sided lapping and their influence on lap wear
PublikacjaPrevious studies on one-sided lapping allow to state that not only parameters of lapping elements (i.e. properties of workpiece, abrasive grains and lapping plate) impact on a lapping efficiency. Influential are also kinematics and dynamics of the process. It is crucial to control an average velocity of lapping (v), a distribution of tangential acceleration (at), a nominal pressure (p), a lapping time (t) and disposal of workpiece...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Analysis of abrasive particle trajectories during single-sided lapping process with driven conditioning ring
PublikacjaIn this paper new kinematics systems were studied for a single lapping process. In order to ensure the constant profile wear of the tool a standard kinematic system can be changed. Lapping is carried out by applying loose abrasive grains between two surfaces and causes a relative motion between them. The result is a finish of multi-directional lay. During process, the mechanism of surface formation are decisively affected by a...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublikacjaResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublikacjaIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublikacjaIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publikacja -
Buckling of frame braced by linear elastic springs
PublikacjaIn the design codes and specifications, simplifed formulae or diagrams are given for determining the buckling lengths of frame columns based on the ruling criterion of considering frames as sway or non sway. Due to the fact that, the code formulae utilize onlylocal stifness distributions, these formulae may yield in certain cases rather erroneous results. In most code formulas a case of weakly braced frames is usually not considered.In...
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane–Mindlin theory with application to damage detection
Publikacja -
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublikacjaIn this study a tin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equatio is derived with aid of the principle of stationary potential energy. The critical load for simply supported bar is found in an analytical form and it is copared with the FEM solution. Sufficient accuracy of the...
-
Numerical Modeling of Steel Surface Hardening in the Process of High Energy Heating by High Frequency Currents
Publikacja -
Quality Improvement of Wear-Resistant Coatings in Plasma Spraying Integrated with High-Energy Heating by High Frequency Currents
Publikacja -
Perspective of High Energy Heating Implementation for Steel Surface Saturation with Carbon
Publikacja -
A new insight into understanding the Crow and Champagne preferred mode: a numerical study
Publikacja -
Simulation of Structure Formation Processes of Dissimilar Steels Welded Joints Using an Intermediate Layer
Publikacja -
Multistage Coupling of Eight Mistuned Bladed Discs on Solid Shaft with 1% Mistuning
Publikacja -
The Influence of Stretch Rod Speed on the Relationship between Preblown Bottle Aesthetic Quality and Final Blown Bottle Thickness Profile in Stretch Blow Molding from Preform Process
PublikacjaFrom a mechanical point of view, the aesthetic quality of preblown PET bottles and thickness profile of final blown PET bottles manufactured in ISBM process are determined by mechanical and thermal response of blown preforms. From the microscopic point of view the biggest influence on the mechanical and thermal properties of PET bottles have orientation and crystallization processes. From a technological point of view, the aesthetic...
-
Experimental and numerical studies of guided wave damage detection in bars with structural discontinuities
PublikacjaPraca dotyczy analizy propagacji fal podłużnych i poprzecznych w elementach prętowych z nieciągłościami strukturalnymi. Symulacje numeryczne przeprowadzone przy zastosowaniu metody elementów spektralnych zostały porównane z wynikami badań eksperymentalnych dla pręta w stanie nienaruszonym oraz dla prętów z rysą, spawem oraz dodatkową masą.
-
Modelling and FE-simulation of plastic ductile damage evolution in plates and shells
Publikacja -
Wideband Radio Direction Finder Implemented in Software Defined Radio Technology
PublikacjaIn the paper a wideband radio direction finder (RDF) implemented in software defined radio (SDR) technology and the results of hardware layer research, including developed antenna switching unit (ASU), are presented. The results of tests of the devices, which are the part of the software defined radio platform (SDRP), and antenna switching unit, confirmed the possibility of using selected components in the final solution.
-
Research and Analysis of Accuracy of Location Estimation in Inertial Navigation System
PublikacjaIn the article the research and analysis of digital signal processing and its influence on accuracy of location estimation in developed inertial navigation system was presented. The purpose of the system is to localize moving people in indoor environment. During research a measuring unit for recording selected movement parameters was made. In the article were also described author’s inertial navigation algorithms.
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane-Mindlin theory with application to damage detection
PublikacjaThis paper presents results of experimental and numerical analyses of in-plane waves propagatingin a 5 mm-thick steel plate in the frequency range of 120-300 kHz. For such a thickness/frequency ratio,extensional waves reveal dispersive character. To model in-plane wave propagation taking into account thethickness-stretch effect, a novel 2D spectral element, based on the Kane-Mindlin theory, was formulated. Anapplication of in-plane...
-
Beam on elastic foundation with anticlastic curvature: Application to analysis of mode I fracture tests
PublikacjaA first order correction is proposed taking into account both interface elasticity and transverse anticlastic curvature of flexible substrate(s) in the DCB (and related tests). Adherends are represented by Kirchhoff-Love plates, and the interface by Winkler-type elastic foundation. Two functions are introduced, representing evolution of beam deflection along the sample midline and anticlastic curvature along the plate. A method...
-
Experimental Validation of Numerical Model within a Flow Configuration of the Model Kaplan Turbine
PublikacjaThis paper investigates validation of flow within a model Kaplan turbine. This includes comparison of various turbulence models and their influence on torque and power generated by the turbine. Numerical results were compared with experimental data.
-
Behaviour of Colliding Multi-Storey Buildings under Earthquake Excitation Considering Soil-Structure Interaction
PublikacjaThis paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using the time history of the Kobe earthquake of 1995. A nonlinear...
-
Nutrient transport and acquisition by diatom chains in a moving fluid
PublikacjaThe role of fluid motion in delivery of nutrients to phytoplankton cells is a fundamental question in biological and chemical oceanography. In the study of mass transfer to phytoplankton, diatoms are of particular interest. They are non-motile, are often the most abundant components in aggregates and often form chains, so they are the ones expected to benefit most from enhancement of nutrient flux due to dissipating turbulence....
-
Doświadczalne badania wytrzymałości zmęczeniowej stopów łożyskowych
PublikacjaW pracy przedstawiono wyniki badań nad wytrzymałością zmęczeniową warstw ślizgowych wykonanych z wybranych materiałów stosowanych w cienkościennych panwiach łożyskowych współczesnych maszyn. Badania przeprowadzono za pomocą urządzeń badawczych skonstruowanych i zbudowanych w Politechnice Gdańskiej. Przedstawiono zaobserwowane pęknięcia zmęczeniowe badanych próbek oraz oszacowano odpowiadające im krytyczne wartości naprężeń w warstwach...
-
Procedura kontrolowanego wywrócenia żurawia stoczniowego
PublikacjaPrzedstawiono procedurę złomowania żurawia stoczniowego, wyposażeniowego. Procedurę tę przeprowadzono w przypadku żurawia uszkodzonego w wyniku katastrofy suwnicy bramowej. Może być również stosowana w przypadkach planowego złomowania wielkich dźwignic.
-
A study on microcrack monitoring in concrete: discrete element method simulations of acoustic emission for non-destructive diagnostics
PublikacjaThe research is focused on the monitoring of fracture evolution in concrete beams under three-point bending using the acoustic emission technique and the discrete element method. The main objective of the study was to numerically and experimentally investigate the mechanism behind the generation of elastic waves during acoustic emission events and their interaction with micro- and macro-cracking in concrete beams under monotonic...
-
On rotary inertia of microstuctured beams and variations thereof
PublikacjaWe discuss the classic rotary inertia notion and extend it for microstructured beams introducing new microinertia parameters as an additional dynamic response to microstructure changes. Slender structures made of beam- or platelet-lattice metamaterials may exhibit not only large translations and rotations but also general deformations of inner structure. Here we considered a few examples of beam-like structures and derive their...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublikacjaThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Continuum models for pantographic blocks with second gradient energies which are incomplete
PublikacjaWe postulate a deformation energy for describing the mechanical behavior of so called pantographic blocks, that is bodies constituted by stacking of layers of pantographic sheets. We remark that the pantographic effect is limited in the plane of pantographic sheets and therefore only the second derivatives of transverse displacements along the pantographic fibers appear in the chosen deformation energy. We use this novel energy...
-
Thermomagnetic behavior of a semiconductor material heated by pulsed excitation based on the fourth-order MGT photothermal model
PublikacjaThis article proposes a photothermal model to reveal the thermo-magneto-mechanical properties of semiconductor materials, including coupled diffusion equations for thermal conductivity, elasticity, and excess carrier density. The proposed model is developed to account for the optical heating that occurs through the semiconductor medium. The Moore–Gibson–Thompson (MGT) equation of the fourth-order serves as the theoretical framework...
-
Design of metamaterials: Preface
PublikacjaThis special issue “Design of metamaterials” collects several papers that have presented theoretical, numerical, and experimental studies of metamaterials.
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublikacjaThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
Experimental study and numerical simulation of the dynamic penetration into dry clay
PublikacjaTests of dry clay were carried out in a uniaxial stress state using the experimental setup which implements the split Hopkinson pressure bar method. Based on the results of these experiments, the compressive strength of clay was determined as an important element of S.S. Grigoryan’s model of the soil medium. In addition, the parameters of this model are determined from the results of experiments using the modified Kolsky method...
-
A general theory for anisotropic Kirchhoff–Love shells with in-plane bending of embedded fibers
PublikacjaThis work presents a generalized Kirchhoff–Love shell theory that can explicitly capture fiber-induced anisotropy not only in stretching and out-of-plane bending, but also in in-plane bending. This setup is particularly suitable for heterogeneous and fibrous materials such as textiles, biomaterials, composites and pantographic structures. The presented theory is a direct extension of classical Kirchhoff–Love shell theory to incorporate...
-
Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates
PublikacjaThe fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were...
-
Strong ellipticity conditions and infinitesimal stability within nonlinear strain gradient elasticity
PublikacjaWe discuss connections between the strong ellipticity condition and the infinitesimal instability within the nonlinear strain gradient elasticity. The strong ellipticity (SE) condition describes the property of equations of statics whereas the infinitesimal stability is introduced as the positive definiteness of the second variation of an energy functional. Here we establish few implications which simplify the further analysis...
-
A chemo-mechano-thermodynamical contact theory for adhesion, friction, and (de)bonding reactions
PublikacjaThis work presents a self-contained continuum formulation for coupled chemical, mechanical, and thermal contact interactions. The formulation is very general and, hence, admits arbitrary geometry, deformation, and material behavior. All model equations are derived rigorously from the balance laws of mass, momentum, energy, and entropy in the framework of irreversible thermodynamics, thus exposing all the coupling present in the...
-
Cavity-expansion approximation for projectile impact and penetration into sand
PublikacjaA one-dimensional problem of a spherical cavity expanding at a constant velocity from zero initial radius in an infinite granular medium, which has the first-kind self-similar solution, is considered. We are solving this dynamic spherical cavity-expansion problem to model rigid spheres penetrating into a granular media. Elastic–plastic deformation of the granular media is described in a barotropic approximation, using the high-pressure...
-
On solvability of initial boundary-value problems of micropolar elastic shells with rigid inclusions
PublikacjaThe problem of dynamics of a linear micropolar shell with a finite set of rigid inclusions is considered. The equations of motion consist of the system of partial differential equations (PDEs) describing small deformations of an elastic shell and ordinary differential equations (ODEs) describing the motions of inclusions. Few types of the contact of the shell with inclusions are considered. The weak setup of the problem is formulated...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublikacjaThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
Response to David Steigmann’s discussion of our paper
PublikacjaWe respond to David Steigmann's discussion of our paper "A general theory for anisotropic Kirchhoff-Love shells with in-plane bending of embedded fibers, Math. Mech. Solids, 28(5):1274-1317" (arXiv:2101.03122). His discussion allows us to clarify two misleading statements in our original paper, and confirm that its formulation is fully consistent with the formulation of Steigmann. We also demonstrate that some of our original statements...
-
On thermal stability of piezo-flexomagnetic microbeams considering different temperature distributions
PublikacjaBy relying on the Euler–Bernoulli beam model and energy variational formula, we indicate critical temperature causes in the buckling of piezo-flexomagnetic microscale beams. The corresponding size-dependent approach is underlying as a second strain gradient theory. Small deformations of elastic solids are assessed, and the mathematical discussion is linear. Regardless of the pyromagnetic effects, the thermal loading of the thermal...
-
Fractographical quantitative analysis of EN-AW 2024 aluminum alloy after creep pre-strain and LCF loading
PublikacjaThis paper explores the applicability of a new damage parameter combining both fracture surface topography and loading features to estimate the fatigue lifetime under creep pre-strain and low-cycle fatigue loading. Fractures of EN-AW 2024 aluminum alloy caused by mixed creep and low-cycle fatigue loading are experimentally characterized and quantified via surface topography analysis. The specimens were preliminary damaged in a...
-
3D Buckling Analysis of a Truss with Horizontal Braces
PublikacjaThe present research is devoted to the study of out–of–plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor 1=4. A linear buckling and a non–linear analysis with geometric and material non–linearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness condition...