Filtry
wszystkich: 4439
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DUST SURFACE DENSITY
-
Surface cracking of laser melted Ti-6Al-4V alloy
PublikacjaOpisano charakterystyczne cechy pękania powierzchniowego obserwowanego po nadtapianiu laserem CO2 i Nd:YAG stopu Ti-6Al-4V. Obserwowano pęknięcia niezależnie od sposobu nadtapiania, penetrujące głęboko strefę przetopioną i w niewielkim stopniu zależne od sposobu nadtapiania. Przypisano obserwowane zjawisko przemianie martenzytycznej i (lub) naprężeniom cieplnym powstającym podczas gwałtownego chłodzenia.
-
Photocatalytic activity and surface properties of carbon-doped titanium dioxide
PublikacjaTiO2 domieszkowany węglem otrzymano poprzez hydrolizę izopropanolanu tytanu(IV) i kalcynację w 350ºC w atmosferze powietrza przez 2h. Przeprowadzone badania wykazały, że fenol (0.21 mM) jest efektywnie degradowany w fazie wodnej, w obecności otrzymanego fotokatalizatora oraz światła z zakresu widzialnego (λ>400 nm). Pole powierzchni właściwej otrzymanego C-TiO2 wynosiło około 127 m2/g, fotokatalizator absorbuje światło z zakresu...
-
Comprehensive investigation of capacitive deionization cells by response surface methodology
Publikacja -
The influence of the temperature treatment on the Nd2-xCexCuO4-y crystals surface
Publikacja -
Influence of abrasive slurry dosage on flat surface lapping effects
PublikacjaPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w obróbce powierzchni płaskich na docierarce jednotarczowej. Analizowano wpływ dawki ścierniwa na wydajność i jakość obróbki elementów ceramicznych i miedzianych.
-
Energy deposition on the inner surface of a Hall Effect thruster for satellite
PublikacjaHET - Hall Effect Thruster, to silnik powszechnie wykorzystywany w kosmonautyce do pozycjonowania satelitów. Medium dostarczającym ciąg silnikowi jest zjonizowany gaz. Praca przedstawia wyniki trzech symulacji komputerowych: 1. Modelowanie sondy Langmuira zanurzonej w plazmie ksenonowej o warunkach zbliżonych do tych panujących w silniku HET. Symulacje wykonano metodą metodą Particle-in-Cell Monte Carlo. Celem była analiza oddziaływania...
-
Strain field of abdominal surface due to patients live excitations
PublikacjaPodano metodę opisu pola odkształceń powierzchni brzucha pacjenta podczas ruchów jego tułowia. Wyróżniono strefy brzucha o zróżnicowanej wielkości odkształceń ekstremalnych.
-
The Effect of Valley Location in Two-Process Surface Topography Analysis
Publikacja -
Preparation and Surface Characterization of Chitosan-Based Coatings for PET Materials
Publikacja -
Reductive Photodegradation of 4,4′-Isopropylidenebis(2,6-dibromophenol) on Fe3O4 Surface
Publikacja -
Damage Development on the Surface of Nickel Coating in the Initial Period of Erosion
PublikacjaThe common occurrence of the phenomenon of cavitation in many industries and the multitude of factors affecting the resistance to cavitation erosion of used materials contribute to the search for methods and appropriate parameters of coating application that are able to minimize the effects of erosion. To determine the validity of the developed application parameters and the method used, cavitation studies and microscopic observations...
-
Assessing the Effects of the Road Surface and Weather Conditions on Road Safety
PublikacjaWhen transport is analysed for its safe delivery the focus is mainly on assessing the safety of roads and the risk of undesired events. These include road accidents, an occurrence which is relatively rare and random. Randomness means that accidents depend on several factors which are partly deterministic (can be controlled) and partly stochastic (random and unpredictable). The set of crash contributing factors can be classified...
-
Periodic and impulsive lubrication of hip joint with stochastic rough surface.
PublikacjaNiniejsza praca przedstawia porównanie wartości nośności uzyskanych numerycznie dla niestacjonarnego smarowania impulsywnego oraz niestacjonarnego smarowania periodycznego sferycznego stawu biodrowego człowieka. W obu przypadkach przyjęto, że smarująca ciecz synowialna ma własności lepkosprężyste a występy chropowatych powierzchni chrząstki stawowej zmieniają się losowo. Charakterystyki zmiennych w czasie rozkładów wartości ciśnienia...
-
Protection of surface water against contamination by wetland systems in Poland
PublikacjaOpisano systemy hydrofitowe stosowane do usuwania zanieczyszczeń z wód powierzchniowych zasilanych wodami opadowymi. Po wprowadzeniu systemów stwierdzono znaczną poprawę jakości wód analizowanych cieków.
-
Laser surface treatment of aluminium-silicon alloy at cryogenic conditions
PublikacjaW artykule przedstawiono wpływ laserowego, powierzchniowego przetapiania w warunkach kriogenicznych na mikrostrukturę, mikrotwardość, zużycie na skutek tarcia oraz korozję stopu aluminium AlSi13Mg1CuNi. Stwierdzono zwiększenie mikrotwardości, odporności na ścieranie i korozję odlewniczego stopu AlSi13Mg1CuNi stosowanego w produkcji tłoków silników spalinowych.
-
Manganese-nitrogen-sulphur surface layers produced on aluminium alloys
PublikacjaPodano metodę wytwarzania warstw powierzchniowych zawierających mangan, azot i siarkę na odlewniczym stopie aluminium. Przedstawiono mikrostrukturę przekroju i powierzchni wytworzonych warstw, ich twardość oraz wlaściwości tribologiczne i korozyjne.
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
The effects of bifunctional linker and reflux time on the surface properties and photocatalytic activity of CdTe quantum dots decorated KTaO3 composite photocatalysts
PublikacjaNovel CdTe-KTaO3composite photocatalysts were successfully synthesized by using thioglycolic acid(TGA) or 3-mercaptopropionic acid (MPA) as linker molecules which facilitated attachment of CdTequantum dots to the surface of KTaO3nanocubes. The as-prepared photocatalysts were characterizedby UV–vis diffuse reflectance spectroscopy (DRS), X-ray diffraction (XRD), scanning electron microscopy(SEM), transmission electron microscopy...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublikacjaIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
Synthesis, characteristics, and photocatalytic activity of zinc oxide nanoparticles stabilized on the stone surface for degradation of metronidazole from aqueous solution
PublikacjaAbstract Background: The presence of antibiotics such as metronidazole in wastewater even at low concentrations requires searching for a suitable process such as advanced oxidation process (AOP) to reduce the level of pollutants to a standard level in water. Methods: In this study, zinc oxide (ZnO) nanoparticles were synthesized by thermal method using zinc sulfate (ZnSO4) as a precursor, then, stabilized on stone and was used...
-
Particle size analysis of suspensions in removing of organic matter and phosphorus from waste water and surface water
PublikacjaIn this paper the particle size of suspended solids in the removing of organic matter and phosphorus compounds from lake- and waste- water treated in the Ecological Treatment Systems (ETS) was analyzed.The invesigated materials were taken from two ETS located in Pomerania Region/Poland. Object in Swarzewo is 3rd stage of biological treatment of municipal waste water, while object in Kartuzy has task to remove a phosphorus from...
-
BET specific surface area measurements of silica-coated bismuth oxide(Bi2O3) and gadolinium oxide (Gd2O3) structures
Dane BadawczeThe BET specific surface area was measured using an N2 adsorption/desorption isotherm (Micromeritics ASAP 2460, Norcross, GA, USA).
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublikacjaAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
Characterization methods of nickel nano-particles obtained by the ex-solution process on the surface of Pr, Ni-doped SrTiO3 perovskite ceramics
PublikacjaIn this paper, a novel electrode material based on Pr, Ni co-doped strontium titanate ( Sr0.7Pr0.3)xTi1−yNiyO3 with constant amount of 30% praseodymium dopant, different amount of nickel (y = 0.06 and y = 0.10) and additional nonstoichiometry in Sr-site (x = 1; x = 0.9 and x = 0.8) was investigated as fuel electrode for SOEC devices. A porous ceramics were prepared by solid-state reaction method. X-ray diffraction measurements...
-
Framework of an Evolutionary Multi-Objective Optimisation Method for Planning a Safe Trajectory for a Marine Autonomous Surface Ship
PublikacjaThis paper represents the first stage of research into a multi-objective method of planning safe trajectories for marine autonomous surface ships (MASSs) involved in encounter situations. Our method applies an evolutionary multi-objective optimisation (EMO) approach to pursue three objectives: minimisation of the risk of collision, minimisation of fuel consumption due to collision avoidance manoeuvres, and minimisation of the extra...
-
Surface modifcation of PMMA polymer detected by XPS
Dane BadawczeIn order to obtain the experimental specimens, four PMMA/PC61BM samples with the following mass proportions were prepared: 10%, 20%, 30%, and 40%. In addition, as a reference, a PMMA sample without PC61BM was prepared as well. For the fabrication process, PC61BM 99.5% (Solenne BV), chloroform HPLC (Sigma Aldrich), and PMMA (commercially available...
-
AFM imaging of surface of modern soldering alloy
Dane BadawczeFollowing the announcement in 2006 of European Union directives aimed at limiting the use of lead in electronic products, there was an urgent need to use lead-free solders in the electronics industry. Due to production requirements, it is necessary to use solders with different melting points. To replace the low-melting eutectic Sn 37 wt. Pb, the most...
-
The Research of the Contamination Levels present in Samples of Precipitation and Surface Waters Collected from the Catchment Area Fuglebekken (Hornsund, Svalbard Archipelago)
PublikacjaPersistent organic pollutants (POPs) are contaminants that may appear in polar regions. In present work surface water was collected from the main stream water in the Fuglebekken basin. The precipitationsamples was collected from the near area by Polish Polar Station in Hornsund. The present investigationreveals the results of the analysis of these samples for their total phenols, formaldehyde, TOC, PAHs and PCBs content. The...
-
Spectroscopic and cytotoxic characteristics of (p-cymene)Ru(II) complexes with bidentate coumarins and density functional theory comparison with selected Pd(II) complexes
PublikacjaThis paper presents the synthesis of two new (p-cymene)-ruthenium(II) complexes with the bidentate coumarin ligands. Both complexes were characterized by FTIR spectroscopy, 1H NMR, 13C NMR, MS, elemental analysis and DFT calculations. The X-ray structure of complex 3a was also solved. The cytotoxic properties of both complexes were examined on human leukemia NALM-6 and HL-60 cells and melanoma WM-115 cells. The complexes possess...
-
Dermal microvessel density and maturity is closely associated with atherogenic dyslipidemia and accumulation of advanced glycation end products in adult patients with type 1 diabetes
Publikacja -
Electrical signatures of Nimbostratus and Stratus clouds in ground-level vertical atmospheric electric field and current density at mid-latitude station Swider, Poland
Publikacja -
Anion–π recognition between [M(CN)6]3− complexes and HAT(CN)6: structural matching and electronic charge density modification
Publikacja -
Evaluation by means of magneto-acoustic emission and Barkhausen effect of time and space distribution of magnetic flux density in ferromagnetic plate magnetized by a C-core
PublikacjaPokazano wyniki badań emisji magnetoakustycznej (EMA) i efektu Barkhausena (HEB) dla dwóch płyt stalowych o różnych wymiarach. Wyniki te są porównane z wynikami modelowania zjawiska EMA z wykorzystaniem metody elementów skończonych z uwzględniem efektu prądów wirowych. Uzyskano zadawalające dopasowanie modelu, który odtwarzał poszerzenie maksimum EMA oraz przesunięcie fazowe i zmianę amplitudy HEB.
-
Radiation dose distributions in three dimensions from tomographic optical density scanning of polymer gels: II. Optical properties of the BANG polymer gel
Publikacja -
Multifrequency Nanoscale Impedance Microscopy (m-NIM): A novel approach towards detection of selective and subtle modifications on the surface of polycrystalline boron-doped diamond electrodes
PublikacjaIn this paper, we describe the modification of Nanoscale Impedance Microscopy (NIM), namely, a combination of contact-mode atomic force microscopy with local impedance measurements. The postulated approach is based on the application of multifrequency voltage perturbation instead of standard frequency-by-frequency analysis, which among others offers more time-efficient and accurate determination of the resultant impedance spectra...
-
Surface activation by cyclic polarization in 1M HCl and its effects on the electrochemical response of CB-PLA 3D printed electrodes
Dane BadawczeThe dataset contains the electrochemical studies performed for surface activation of the CB-PLA 3D printed electrodes by electrolysis in 1M HCl solution. The studies were performed after treatment at different polarization ranges, as labeled in subfolder names. For each electrode the consecutive studies describe different samples, as labeled in subfolders:...
-
Changes on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
PublikacjaSol–gel layers have been the subject of many studies in recent decades. However, very little information exists about layers in which carbon structures are developed in situ. Using the spin-coating method, we obtained thin iron-doped SiO2/C composite films. The results of Raman spectroscopy showed that our samples consisted of graphitic forms and polymers. The latter’s contribution decreases with rising temperature. FTIR and EDS...
-
Post-critical buckling of truncated conical carbon nanotubes considering surface effects embedding in a nonlinear Winkler substrate using the Rayleigh-Ritz method
PublikacjaThis research predicts theoretically post-critical axial buckling behavior of truncated conical carbon nanotubes (CCNTs) with several boundary conditions by assuming a nonlinear Winkler matrix. The post-buckling of CCNTs has been studied based on the Euler-Bernoulli beam model, Hamilton’s principle, Lagrangian strains, and nonlocal strain gradient theory. Both stiffness-hardening and stiffness-softening properties of the nanostructure...
-
Assessment of Surface Water Resources Based on Different Growth Scenarios, for Borkena River Sub-basin, Awash River Basin, Ethiopia
PublikacjaThe total annual river flow at the Awash Kombolcha sub-basin of the Borkena river station was estimated to be 4.6 billion cubic meters by 2019-2030. The current average annual flow at the exit measurement station is 544.5Mm3 of the water resources available in the study area. The monthly peak flow of the Borkena River occurs from July to September. In addition, the highest monthly average flow is in August and the lowest is...
-
Methodology for Carrying Out Measurements of the Tombolo Geomorphic Landform Using Unmanned Aerial and Surface Vehicles near Sopot Pier, Poland
PublikacjaThe human impact on the ecosystem has been particularly evident in the last century; it transforms the Earth’s surface on an unprecedented scale and brings about irreversible changes. One example is an oceanographic phenomenon known as a tombolo, i.e., a narrow belt connecting the mainland with an island lying near the shore formed as a result of sand and gravel being deposited by sea currents. The phenomenon contributes to an...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Towards classification of patients based on surface EMG data of temporomandibular joint muscles using self-organising maps
PublikacjaThe study considers the need for an effective method of classification of patients with a temporomandibular joint disorder (TMD). The self-organising map method (SOM) was applied to group patients and used together with the cross-correlation approach to interpret the processed (rectified and smoothed by using root mean square (RMS) algorithm) surface electromyography signal (sEMG) obtained from testing the muscles (two temporal...
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublikacjaNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
The use of response surface methodology for reliability estimation of composite engineering structures
Publikacja -
Experimental study of heat transfer intensification in surface cooling using microjets
PublikacjaW pracy przedstawiono badania eksperymentalne intensyfikacji wymiany ciepła podczas chłodzenia powierzchni mikrostrugami. Wyniki badań porównano z własnym modelem teoretycznym zjawiska.
-
Identification and antimicrobial resistance of Enterococcus spp. isolated from surface water
PublikacjaIn the study species distributions and antimicrobial resistance profiles were determined among riverine Enterococcus spp. Susceptibility of the isolates was tested against: ampicillin, imipenem, teicoplanin, vancomycin, erythromycin, linezolid, fosfomycin, ciprofloxacin,levofloxacin, moxifloxacin, tetracycline, high levels of gentamicin and streptomycin. The enterococci were detected in all of the analyzed water samples, periodically...
-
Daily Radiation Budget of the Baltic Sea Surface from Satellite Data
Publikacja -
A GIS based approach for the mitigation of surface runoff to a shallow lowland reservoir
Publikacja -
Perspective of High Energy Heating Implementation for Steel Surface Saturation with Carbon
Publikacja