Wyniki wyszukiwania dla: numerical methods
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Fast EM-Driven Parameter Tuning of Microwave Circuits with Sparse Sensitivity Updates via Principal Directions
PublikacjaNumerical optimization has become more important than ever in the design of microwave components and systems, primarily as a consequence of increasing performance demands and growing complexity of the circuits. As the parameter tuning is more and more often executed using full-wave electromagnetic (EM) models, the CPU cost of the overall process tends to be excessive even for local optimization. Some ways of alleviating these issues...
-
Computationally-efficient design optimisation of antennas by accelerated gradient search with sensitivity and design change monitoring
PublikacjaElectromagnetic (EM) simulation tools are of primary importance in the design of contemporary antennas. The necessity of accurate performance evaluation of complex structures is a reason why the final tuning of antenna dimensions, aimed at improvement of electrical and field characteristics, needs to be based on EM analysis. Design automation is highly desirable and can be achieved by coupling EM solvers with numerical optimisation...
-
Dimensionality-Reduced Antenna Modeling with Stochastically Established Constrained Domain
PublikacjaOver the recent years, surrogate modeling methods have become increasingly widespread in the design of contemporary antenna systems. On the one hand, it is associated with a growing awareness of numerical optimization, instrumental in achieving high-performance structures. On the other hand, considerable computational expenses incurred by massive full-wave electromagnetic (EM) analyses, routinely employed as a major design tool,...
-
O badaniach i analizach mostów tymczasowych typu Bailey - MS 22-80
PublikacjaPrzedstawiono sposoby modelowania oraz wyniki badań in situ konstrukcji mostów tymczasowych typu Bailey - MS 22-80. Sformuowano wnioski dotyczące rzeczywistego zachowania się tego rodzaju konstrukcji oraz zasad modelowania w celu jednoznacznego określenia pracy i wytężenia ustroju.
-
Low-cost multi-objective optimization and experimental validation of UWB MIMO antenna
PublikacjaPurpose–The purpose of this paper is to validate methodologies for expedited multi-objective designoptimization of complex antenna structures both numerically and experimentally.Design/methodology/approach–The task of identifying the best possible trade-offs between theantenna size and its electrical performance is formulated as multi-objective optimization problem.Algorithmic frameworks are described for finding Pareto-optimal...
-
Identification of Unstable Reference Points and Estimation of Displacements Using Squared Msplit Estimation
PublikacjaThe article presents a new version of the method for estimating parameters in a split functional model, which enables the determination of displacements of geodetic network points with constrained datum. The main aim of the study is to present theoretical foundations of Msplit CD estimation and its basic properties and possible applications. Particular attention was paid to the efficacy of the method in the context of geodetic...
-
Resistant to correlated noise and outliers discrete identification of continuous non-linear non-stationary dynamic objects
PublikacjaIn this article, specific methods of parameter estimation were used to identify the coefficients of continuous models represented by linear and nonlinear differential equations. The necessary discrete-time approximation of the base model is achieved by appropriately tuned FIR linear integral filters. The resulting discrete descriptions, which retain the original continuous parameterization, can then be identified using the classical...
-
Resistant to correlated noise and outliers discrete identification of continuous non-linear non-stationary dynamic objects
PublikacjaIn this study, dedicated methods of parameter estimation were used to identify the coefficients of continuous models represented by linear and nonlinear differential equations. The necessary discrete-time approximation of the base model is achieved by appropriately tuned FIR linear integral filters. The resulting discrete descriptions, which retain the original continuous parameterization, can then be identified using the classical...
-
Non-Destructive Testing of a Sport Tribune under Synchronized Crowd-Induced Excitation Using Vibration Analysis
PublikacjaThis paper presents the concept of repairing the stand of a motorbike speedway stadium. The synchronized dancing of fans cheering during a meeting brought the stand into excessive resonance. The main goal of this research was to propose a method for the structural tuning of stadium stands. Non-destructive testing by vibration methods was conducted on a selected stand segment, the structure of which recurred on the remaining stadium...
-
Hybridization of the FDTD method with use of the discrete Green's function
PublikacjaIn this contribution, a hybrid technique is presented which combines the finite-difference time-domain (FDTD) method and the discrete Green's function (DGF) formulation of this method. FDTD is a powerful technique for the analysis of complex penetrable objects but its application is not efficient when the computational domain includes many free-space cells. Therefore, the hybrid method was developed which is applicable to complex...
-
Wpływ właściwości cieczy hydraulicznej na wartość skoków ciśnienia w komorach pomp tłoczkowych osiowych
PublikacjaPublikacja dotyczy badań skoków ciśnienia w komorach roboczych pomp tłoczkowych osiowych. Skupiono się w nim na wpływie właściwości cieczy hydraulicznej na wartość skoków ciśnienia. Przeanalizowano wpływ takich parametrów jak: -gęstość, -lepkość, -ściśliwość, -zapowietrzenie. Do określenia wpływu właściwości cieczy na skoki ciśnienia wykorzystano badania laboratoryjne i symulacje komputerowe.
-
Advanced Experimental and Numerical Analysis of Behavior Structural Materials Including Dynamic Conditions of Fracture for Needs of Designing Protective Structures
Publikacja -
Numerical Modeling of Hydrogen-Rich Gas Production From Gasoline Autothermal Reforming in a Plug Flow Reactor for Electric Vehicles
Publikacja -
Experimental and numerical investigation of crosstalk effect in coupled coplanar waveguides - part i: bi-mode coupled line representation
PublikacjaW pracy przedstawiono analizę zjawiska przesłuchu w strukturze sprzężonych falowodów koplanarnych. Analiza wykorzystując metodę przestrzeni widmowej i bazując na dwurodzajowym modelu pary linii sprzężonych uwzględnia efekty dyspersji obserwowane w zakresie wysokich częstotliwośći. Przedyskutowano zagadnienie sposobu definicji impedancji charakterystycznych dla prowadzonych rodzajów pola. Wyniki modelowania numerycznego potwierdzono...
-
An investigation of structural responses of inverted pavements by numerical approaches considering nonlinear stress-dependent properties of unbound aggregate layer
Publikacja -
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublikacjaThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Numerical Analysis of an Impact of Planned Location of Sewage Discharge on Natura 2000 Areas – The Dead Vistula Region Case Study
PublikacjaThis article presents results of an analysis of impact of a designed discharge of contaminated water into the Dead Vistula (Wisła Martwa) in the region of the Isthmus (Przesmyk) with the aim of determination of a possible effect of the pollution onto protected areas of Natura 2000 (bird habitats and sites, especially the Bird Paradise – Ptasi Raj) nature reserve. The analysis was conducted on the basis of the two-dimensional modelling...
-
Numerical Analysis of TB32 Crash Tests for 4-cable Guardrail Barrier System Installed on the Horizontal Convex Curves of Road
PublikacjaHorizontal curves are one of the elements of road infrastructure where statistically a relatively high number of accidents have been reported. In the last ten years in Poland approx. 10% of all road accidents happened on horizontal curves of roads and was responsible for approx. 14% of all fatalities on Polish roads. Thus, this issue is important and requires extensive research and proper road safety treatments. One possible measure...
-
NUMERICAL ANALYSIS OF SPECIES DIFFUSION AND METHANOL DECOMPOSITION IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF Ni3Al FOR LOW REYNOLDS NUMBERS
PublikacjaNumerical modelling of hydrogen production by means of methanol decomposition in a thermocatalytic reactor using corrugated foil made of the Ni3Al intermetallic phase is shown in the paper. Experimental results of the flow analysis of mixtures containing helium and methanol in a thermocatalytic reactor with microchannels were used for the initial calibration of the CFD calculations (calculations based on the Computational Fluid...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublikacjaAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
Numerical modeling of PFAS movement through the vadose zone: Influence of plant water uptake and soil organic carbon distribution
PublikacjaIn this study, we investigated the effects of soil organic carbon (SOC) distribution and water uptake by plant roots on PFAS movement in the vadose zone with a deep groundwater table under temperate, humid climate conditions. Two series of numerical simulations were performed with the HYDRUS computer code, representing the leaching of historical PFOS contamination and the infiltration of water contaminated with PFOA, respectively. We...
-
THIRD-ORDER EXPONENTIAL INTEGRATOR FOR LINEAR KLEIN–GORDON EQUATIONS WITH TIME AND SPACE-DEPENDANT MASS
PublikacjaAllowing for space- and time-dependance of mass in Klein–Gordon equations re- solves the problem of negative probability density and of violation of Lorenz covariance of interaction in quantum mechanics. Moreover it extends their applicability to the domain of quantum cosmology, where the variation in mass may be accompanied by high oscillations....
-
THIRD-ORDER EXPONENTIAL INTEGRATOR FOR LINEAR KLEIN–GORDON EQUATIONS WITH TIME AND SPACE-DEPENDANT MASS
PublikacjaAllowing for space- and time-dependance of mass in Klein–Gordon equations re- solves the problem of negative probability density and of violation of Lorenz covariance of interaction in quantum mechanics. Moreover it extends their applicability to the domain of quantum cosmology, where the variation in mass may be accompanied by high oscillations....
-
Material Parameters Identification of Historic Lighthouse Based on Operational Modal Analysis
PublikacjaIn the present paper, the identification of the material parameters of a masonry lighthouse is discussed. A fully non-invasive method was selected, in which the material properties were determined via numerical model validation applied to the first pair of natural frequencies and their related mode shapes, determined experimentally. The exact structural model was built by means of the finite element method. To obtain experimental...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Simulation of unsteady flow over floodplain using the diffusive wave equation and the modified finite element method
PublikacjaWe consider solution of 2D nonlinear diffusive wave equation in a domain temporarily covered by a layer of water. A modified finite element method with triangular elements and linear shape functions is used for spatial discretization. The proposed modification refers to the procedure of spatial integration and leads to a more general algorithm involving a weighting parameter. The standard finite element method and the finite difference...
-
Modelling and simulations in time-fractional electrodynamics based on control engineering methods
PublikacjaIn this paper, control engineering methods are presented with regard to modelling and simulations of signal propagation in time-fractional (TF) electrodynamics. That is, signal propagation is simulated in electromagnetic media described by Maxwell’s equations with fractional-order constitutive relations in the time domain. We demonstrate that such equations in TF electrodynamics can be considered as a continuous-time system of...
-
Uproszczone metody obliczania wyboczenia silosów z blachy falistej wzmocnionych słupami na podstawie analizy MES i wyników doświadczalnych
PublikacjaRozprawa doktorska dotyczy zagadnienia stateczności i nośności granicznej stalowych silosów z płaszczem z blachy falistej wzmocnionych pionowymi słupami. Przeprowadzono zaawansowane analizy numeryczne MES oraz badania doświadczalne dotyczące wyboczenia/stateczności analizowanych silosów. Analizy numeryczne zostały przeprowadzone w zakresie liniowej oraz nieliniowej analizy stateczności, z uwzględnieniem wstępnych imperfekcji geometrycznych...
-
Coupled nonlinear Schrödinger equations in optic fibers theory
PublikacjaIn this paper a detailed derivation and numerical solutions of CoupledNonlinear Schr¨odinger Equations for pulses of polarized electromagnetic wavesin cylindrical fibers has been reviewed. Our recent work has been compared withsome previous ones and the advantage of our new approach over other methods hasbeen assessed. The novelty of our approach lies is an attempt to proceed withoutloss of information within the frame of basic...
-
Solving Boundary Value Problems for Second Order Singularly Perturbed Delay Differential Equations by ε-Approximate Fixed-Point Method
PublikacjaIn this paper, the boundary value problem for second order singularly perturbed delay differential equation is reduced to a fixed-point problem v = Av with a properly chosen (generally nonlinear) operator A. The unknown fixed-point v is approximated by cubic spline vh defined by its values vi = vh(ti) at grid points ti, i = 0, 1, ... ,N. The necessary for construction the cubic spline and missing the first derivatives at the boundary...
-
Airfoil Design Under Uncertainty Using Non-Intrusive Polynomial Chaos Theory and Utility Functions
PublikacjaFast and accurate airfoil design under uncertainty using non-intrusive polynomial chaos (NIPC) expansions and utility functions is proposed. The NIPC expansions provide a means to efficiently and accurately compute statistical information for a given set of input variables with associated probability distribution. Utility functions provide a way to rigorously formulate the design problem. In this work, these two methods are integrated...
-
Optimization of Wireless Networks for Resilience to Adverse Weather Conditions
PublikacjaIn this chapter, we consider how adverse weather conditions such as rain or fog affect the performance of wireless networks, and how to optimize these networks so as to make them robust to these conditions. We first show how to analyze the weather conditions in order to make them useful for network optimization modelling. Using an example realistic network, we show how to optimize two types of wireless networks: free-space optical...
-
Hybrid Technique Combining the FDTD Method and Its Convolution Formulation Based on the Discrete Green's Function
PublikacjaIn this letter, a technique combining the finite-difference time-domain (FDTD) method and its formulation based on the discrete Green's function (DGF) is presented. The hybrid method is applicable to inhomogeneous dielectric structures that are mutually coupled with wire antennas. The method employs the surface equivalence theorem in the discrete domain to separate the problem into a dielectric domain simulated using the FDTD method...
-
Mariusz Figurski prof. dr hab. inż.
OsobyDyrektor Centrum Modelowania Meteorologicznego Instytut Meteorologii i Gospodarki Wodnej - Państwowy Instytut Badawczy. Urodził się 27 kwietnia 1964 roku w Łasinie. Egzamin maturalny złożył w 1983 roku po ukończeniu II Liceum Ogólnokształcącego im. Jana III Sobieskiego w Grudziądzu, Studia wyższe w trybie indywidualnym ukończył w 1989 (10.07.1989) na Wydziałach Elektromechanicznym i Inżynierii Lądowej i Geodezji Wojskowej Akademii...
-
Accelerated Gradient-Based Optimization of Antenna Structures Using Multi-Fidelity Simulations and Convergence-Based Model Management Scheme
PublikacjaThe importance of numerical optimization has been steadily growing in the design of contemporary antenna structures. The primary reason is the increasing complexity of antenna topologies, [ a typically large number of adjustable parameters that have to be simultaneously tuned. Design closure is no longer possible using traditional methods, including theoretical models or supervised parameter sweeping. To ensure reliability, optimization...
-
Remarks on evaluation of spectral radius of operators arising in WR methods for linear systems of ODEs
PublikacjaW pracy omawiane są różne metody oszacowania promienia spektralnego. Do oszacowań tych użyto elementarnych metod. Jedną z nich jest metoda wykorzystująca normę Bieleckiego. Jedną z zalet takich metod wyraźnie widać na przykładzie równań różniczkowych z opóźnieniem, gdzie oszacowania promienia spektralnego zależą od charakteru opóźnienia.
-
THREE-DIMENSIONAL numerical investigation of MHD nanofluid convective heat transfer inside a CUBIC porous container with corrugated bottom wall
PublikacjaSimultaneous use of porous media and nanofluid as a heat transfer improvement method has recently captivated a great deal of attention. The heat transfer and entropy production of the Cu-water nanofluid inside a cubic container with a heated bottom wavy wall and an elliptic inner cylinder were numerically analyzed in this study. The container is partitioned into two sections: the left side is filled with permeable media and...
-
Numerical analysis of the two‐phase steam‐air heat transfer flow induced in smooth and corrugated channel using the VOF model
Publikacja -
THREE-DIMENSIONAL NUMERICAL INVESTIGATION OF MHD NANOFLUID CONVECTIVE HEAT TRANSFER INSIDE A CUBIC POROUS CONTAINER WITH CORRUGATED BOTTOM WALL
Publikacja -
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublikacjaMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublikacjaIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Corrosion damage identification based on the symmetry of propagating wavefield measured by a circular array of piezoelectric transducers: Theoretical, experimental and numerical studies
PublikacjaThe article investigates the results obtained from numerical simulations and experimental tests concerning the propagation of guided waves in corroded steel plates. Developing innovative methodologies for assessing corrosion-induced degradation is crucial for accurately diagnosing offshore and ship structures exposed to harsh environmental conditions. The main aim of the research is to analyze how surface irregularities affect...
-
Karolina Lademann mgr
OsobyCurriculum vitae
-
An Instantaneous Engine Speed Estimation Method Using Multiple Matching Synchrosqueezing Transform
PublikacjaInstantaneous rotational speed measurement of the engine is crucial in routine inspection and maintenance of an automobile engine. Since the contact measurement of rotational speed is not always available, the vibration measurement has been used for noncontact rotational speed estimation methods. Unfortunately, the accuracy of the noncontact estimation methods by analyzing engine vibration frequency is not satisfactory due to the...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublikacjaNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
Variable-fidelity shape optimization of dual-rotor wind turbines
PublikacjaPurpose Dual-rotor wind turbines (DRWTs) are a novel type of wind turbines that can capture more power than their single-rotor counterparts. Because their surrounding flow fields are complex, evaluating a DRWT design requires accurate predictive simulations, which incur high computational costs. Currently, there does not exist a design optimization framework for DRWTs. Since the design optimization of DRWTs requires numerous model...
-
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublikacjaW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...
-
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublikacjaW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM, z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...