Wyszukiwarka
Wyniki wyszukiwania dla: flow control
-
A High-Arctic flow-through lake system hydrochemical changes: Revvatnet, southwestern Svalbard (years 2010–2018)
PublikacjaLake ecosystems are strongly coupled to features of their surrounding landscapes such as geomorphology, lithology, vegetation and hydrological characteristics. In the 2010–2018 summer seasons, we investigated an Arctic flow-through lake system Revvatnet, located in the vicinity of the coastal zone of Hornsund fjord in Svalbard, characterising its hydrological properties and the chemical composition of its waters. The lake system...
-
Uncertainty of mass flow measurement using centric and eccentric orifice for Reynolds number in the range 10,000 ≤ Re ≤ 20,000
PublikacjaThe article analyses the impact of the Reynolds number on the estimated uncertainty of the mass flow rate measurement using an orifice plate. The objects of the research were two types of orifices: centric (ISA) and eccentric, with the diameter ratio β = 0.5. Studies were performed by Monte Carlo simulation and experiments for Reynolds numbers in the range 10,000 ≤ Re ≤ 20,000. The obtained results have shown that for both orifice...
-
Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy–Weisbach equation and the issue of friction factor
PublikacjaIn this article, we consider the modelling of stationary incompressible and isothermal one-dimensional fluid flow through a long pipeline. The approximation of the average pressure in the developed model by the arithmetic mean of inlet and outlet pressures leads to the known empirical Darcy–Weisbach equation. Most importantly, we also present another improved approach that is more accurate because the average pressure is estimated...
-
Pressure-induced flow processing behind the superior mechanical properties and heat-resistance performance of poly(butylene succinate)
PublikacjaWe propose a pressure-induced flow (PIF) processing method for the simultaneous enhancement of strength, toughness, and heat resistance of biodegradable poly(butylene succinate) (PBS). The pressure and temperature were systematically adjusted to optimize the tensile strength of PBS. Under the optimized processing conditions, the structured PBS was characterized by relatively high strength of 89.5 MPa, toughness of 21.4 kJ·m−2 ,...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublikacjaThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Modelling of shear localization during granular flow within non-local hypoplasticity using material point method
PublikacjaArtykuł omawia wyniki numeryczne dotyczące powstawania lokalizacji odkształceń stycznych w materiałach granulowanych Obliczenia wykonano dla ściskania dwuosiowego i przypływu silosowego stosując hipoplastyczny model konstytutywny rozszerzony o długość charakterystyczną w ramach nielokalnej teorii. Zastosowano podejście punktów materialnych w celu uniknięcia nadmiernej deformacji elementów skończonych.
-
ANALYSIS AND OPTIMIZATION OF ELECTRIC VEHICLE CHARGING PROCESSES IN TRANSACTIVE ENERGY SYSTEMS
PublikacjaThe implementation of smart charging of electric vehicles allows operators of local power networks and electricity suppliers to implement new business models for the interaction of electric vehicles with the network. In addition to the optimal selection of Microgrid capacities when charging electric vehicles, it is also important to use different charging methods. To satisfy the interests of all participants of local systems from...
-
Studying the Effect of Working Conditions on WEDM Machining Performance of Super Alloy Inconel 617
PublikacjaWire electrical discharge machining (WEDM) has been for many years a precise and efficient non-conventional manufacturing solution in various industrial applications, mostly involving the use of hard-to machine materials like, among other, the Inconel super alloys. The focus of the present study is on exploring the effect of selected control parameters, including pulse duration, pulse-off time and the dielectric flow pressure on...
-
Dynamic model of nuclear power plant turbine
PublikacjaThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
Immobilization of TiO2 and Fe–C–TiO2 photocatalysts on the cotton material for application in a flow photocatalytic reactor for decomposition of phenol in water
Publikacja -
Numerical Modeling of Hydrogen-Rich Gas Production From Gasoline Autothermal Reforming in a Plug Flow Reactor for Electric Vehicles
Publikacja -
Friction and flow around growing tissue in bioreactor. Proceedings of the Biomechanics 2003. Engineering Biomechanics - Biomechanics of Sport - Medical Biomechanics.
PublikacjaPrzedstawione zostały problemy teoretyczne związane z wyznaczaniem sił tarcia, współczynników tarcia, rozkładów wartości ciśnienia w warstwie przyściennej wytworzonej wokół hodowanej tkanki w bioreaktorze w trakcie opływu tej tkanki cieczami biologicznymi o właściwościach lepkosprężystych. Model Rivlina Ericksena lepkosprężystej cieczy biologicznej jest tu brany pod uwagę.
-
Potential and limits of landfill leachate treatment in a multi-stage subsurface flow constructed wetland – evaluation of organics and nitrogen removal
PublikacjaConstructed wetlands have potential of treating wastewater of poor biodegradability. The performance of a multistage sub-surface flow wetland treating municipal landfill leachate was assessed during three years of operation. During the study three research periods with different operation conditions were established. The hydralic loads, operation mode of vertical flow beds and type of treated wastewater (raw leachate – leachate...
-
Examples of numerical simulations of two-dimensional unsaturated flow with VS2DI code using different interblock conductivity averaging schemes
PublikacjaFlow in unsaturated porous media is commonly described by the Richards equation. This equation is strongly nonlinear due to interrelationships between water pressure head (negative in unsaturated conditions), water content and hydraulic conductivity. The accuracy of numerical solution of the Richards equation often depends on the method used to estimate average hydraulic conductivity between neighboring nodes or cells of the numerical...
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublikacjaW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
High-speed multi-stage gas-steam turbine with flow bleeding in a novel thermodynamic cycle for decarbonizing power generation
PublikacjaIn the global pursuit of sustainable energy and reduced carbon footprints, advances in power generation techniques play a crucial role, not only in meeting the ever-increasing energy demands but also in ensuring that environmental standards are maintained and that the health of our planet is prioritized for future generations. In the ongoing quest for sustainable energy solutions, novel high-speed multi-stage gas-steam turbine...
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublikacjaThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
Galerkin Finite Element Process for Entropy Production and Thermal Evaluation of Third-Grade Fluid Flow: A Thermal Case Study
Publikacja: A fluid’s moving class improves its heat transmission capability, as well as its rigidity, owing to multivariate molecule suspension. In this way, nanofluids are superior to common fluids. In this study, we evaluated the features of ease and heat transfer. Furthermore, we investigated permeable media, heat source, variable heat conductivity, and warm irradiation results. A mathematical technique known as the Galerkin finite element...
-
A pilot study with flow mediated skin fluorescence: A novel device to assess microvascular endothelial function in coronary artery disease
PublikacjaBackground: Endothelial dysfunction is one of the earliest vascular manifestations in the pathogenesis of cardiovascular disease. Noninvasive, simple and inexpensive methods of endothelial function assessment are therefore needed. Methods: Microvascular endothelial function was assessed in coronary artery disease (CAD) patients by flow mediated skin fluorescence (FMSF), based on measurements of NADH fluorescence intensity during...
-
Reliability and efficiency of pollution removal during long-term operation of a one-stage constructed wetland system with horizontal flow
PublikacjaThe paper presents the results of a study of the reliability and efficiency of pollutant removal during long term operation of a one-stage constructed wetland system with horizontal flow. The flow rate of the wastewater treatment plant was 1.2 m3·d-1 during the research period. Physical and chemical analyses of raw wastewater and treated effluent were carried out in the years 1997–2010 (14 years). During this study period, 56 series...
-
Adaptation of the arbitrary Lagrange–Euler approach to fluid–solid interaction on an example of high velocity flow over thin platelet
PublikacjaThe aim of this study is to analyse the behaviour of a thin plate with air flow velocities of 0.3–0.9 Ma. Data from the experiment and numerical tools were used for the analysis. For fluid–solid interaction calculations, the arbitrary Lagrange–Euler approach was used. The results of the measurements are twofold. The first one is the measurement of the flow before and after vibrating plate, i.e. pure flow plate, and the second consists...
-
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublikacjaThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Modelling of full-scale silo experiments with flow correcting inserts using material point method (MPM) based on hypoplasticity.
PublikacjaCharakterystyki przepływu materiałów sypkich w silosach mają znaczenie dla naporów wywieranych na ściany silosu. Można je zmieniać za pomocą różnych wkładek. W pracy omówiono wyniki liczbowe dotyczące ograniczonego przepływu niespoistego ziarnistego piasku w pełnowymiarowym silosie metalowym z różnymi symetrycznie rozmieszczonymi wkładami, służącymi do korekcji wzorca przepływu (podwójny stożek, stożek w stożku i odwrócony stożek)....
-
Modeling of patterns of shear zones during granular flow in silos using uncoupled ALE-formulation and non-local hypoplasticity
PublikacjaW artykule przedstawiono wyniki numerycznej analizy lokalizacji odkształceń w materiałach granulowanych podczas przepływu w silosach. Obliczenia wykonano przy zastosowaniu metody elementów skończonych w podejściu ALE i mikropolarnego modelu hipoplastycznego. Pokazano wpływ szorstkości ścian silosu i zagęszczenia materiału sypkiego na typ lokalizacji.
-
The study of the influence of ZnO nanoparticles on pyocyanin production - the optimization of production and the study of the physiological response of the cells
Dane BadawczeThis dataset presents the in-depth analysis of the influence of zinc oxide nanoparticles on pyocyanin production.
-
Particle rotation effects in Cosserat-Maxwell boundary layer flow with non-Fourier heat transfer using a new novel approach
Publikacja -
Erosion under turbulent slurry flow: An experimental determination of particle impact angle, impact direction, and distribution thereof by image processing
Publikacja -
Acute Effects of Continuous and Intermittent Blood Flow Restriction on Movement Velocity During Bench Press Exercise Against Different Loads
Publikacja -
Numerical analysis of the two‐phase steam‐air heat transfer flow induced in smooth and corrugated channel using the VOF model
Publikacja -
Galerkin finite element analysis of Darcy–Brinkman–Forchheimer natural convective flow in conical annular enclosure with discrete heat sources
Publikacja -
Heat and mass transfer characteristics in MHD Casson fluid flow over a cylinder in a wavy channel: Higher-order FEM computations
Publikacja -
Polymorphic microsatellite markers demonstrate hybridization and interspecific gene flow between lumbricid earthworm species, Eisenia andrei and E. fetida
Publikacja -
Towards application of uncertainty quantification procedure combined with experimental procedure for assessment of the accuracy of the DEM approach dedicated for granular flow modeling
PublikacjaThere is a high demand for accurate and fast numerical models for dense granular flows found in many industrial applications. Nevertheless, before numerical model can be used its need to be always validated against experimental data. During the validation, it is important to consider how the measurement data sets, as well as the numerical models, are affected by errors and uncertainties. In this study, the uncertainty quantification...
-
About definition of modes and magnetosonic heating in a plasma’s flow: Especial cases of perpendicular and nearly perpendicular wave vector and magnetic field
PublikacjaDynamics of hydrodynamic perturbations in a plasma depend strongly on an angle between the wave vector and equilibrium straight magnetic field. The case of perpendicular propagation is especial. There are only two (fast) magnetosonic modes since two (slow) ones degenerate into the stationary one with zero speed of propagation. This demands individual definition of wave modes by the links of hydrodynamic relations. These links are...
-
Influence of Acute Jugular Vein Compression on the Cerebral Blood Flow Velocity, Pial Artery Pulsation and Width of Subarachnoid Space in Humans
PublikacjaCelem pracy jest zaprezentowanie wyników badań dotyczących oceny wpływu silnego obustronnego zwężenia żył szyjnych na amplitudę pulsacji i zmiany szerokości przestrzeni podpajęczynówkowej, prędkość przepływu mózgowego krwi, obwodowe ciśnienie krwi oraz możliwe relacje między wymienionymi parametrami.
-
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublikacjaMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Investigations of porosity changes during granular silo flow using Electrical Capacitance Tomography (ECT) and Particle Image Velocimetry (PIV)
PublikacjaArtykuł omawia pomiary zmian porowatości podczas przepływu silosowego materiału granulowanego. Zastosowano 2 techniki: tomografie i optoelektroniczną DIC. Pomiary wykonano dla różnych początkowych zagęszczeń oraz szorstkości ścian.
-
TRANSFER OF ELECTRIC ENERGY [2023/24]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
TRANSFER OF ELECTRIC ENERGY [2022/23]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
TRANSFER OF ELECTRIC ENERGY [2024/25]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage, power,...
-
TRANSFER OF ELECTRIC ENERGY [2024/25]
Kursy OnlineCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublikacjaSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
The flow of nitrogen into the euphotic zone of the Baltic Proper as a result of the vertical migration of phytoplankton: An analysis of the long-term observations and ecohydrodynamic model simulation
Publikacja -
Neoplasia detection in Macoma balthica (Bivalvia) from the Gulf of Gdansk (Baltic Sea, Poland) — comparison of flow cytometry, histology and chromosome analysis.
Publikacja -
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
Publikacja -
Effect of Laminar Pulsatile Fluid Flow on Separation of Volatile Organic Compounds from Aqueous Solution by a Hollow Fiber Membrane-Based Process
PublikacjaIn this study, a laminar pulsatile fluid flow was used for the separation of benzene, toluene, ethylbenzene, and xylene isomers (BTEX) from aqueous solutions. Polyether sulfone hollow fiber membrane has been applied to this process. The effects of BTEX concentration, and feed and extraction flow rates were examined. It was found that the application of the pulsatile fluid flow with...
-
3D calculations of aerodynamic forces causing self-excited vibrations of turbine rotor systems. Part I: Shroud seal flow inwestigations
PublikacjaOpisano numeryczną i doświadczalną metodę badania przepływu w uszczelnieniu nadbandażowym stopnia turbinowego. Badania numeryczne przeprowadzono programem Fluent, a badania doświadczalne wykonano na powietrznej turbinie modelowej. Uwzględniono niesymetryczny rozkład szczeliny nadbandażowej na skuteknie centrycznego położenia osi wirnika względem osi cylindra. Zamieszczono przykładowe wyniki.
-
Modelowanie przepływu wód podziemnych w strefie brzegowej morza - możliwości prognozowania = Groundwater flow modeling in the coastline area - prediction possibilities
PublikacjaSpecyficzne warunki występowania wód podziemnych w strefie brzegowej morza sprawiają, że ich eksploatacja jest sprawą złożoną i powinna być weryfikowana na modelu numerycznym. Zasadniczym zagrożeniem jest ingresja słonych wód morskich, która może być wzbudzona eksploatacją. Innym czynnikiem, który może przyczynić się do ingresji wód słonych do warstwy wodonośnej może być podniesienie się poziomu morza. W pracy przedstawiono wyniki...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublikacjaMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Hydrostatic drives as safe and energy saving machines. The drive investigation method compatible diagram of power increase opposite to the direction of power flow
PublikacjaProjektanci i producenci napędu hydrostatycznego nie dysponują możliwością dokładnego określania jego sprawności energetycznej zmieniającej się szeroko w polu pracy napędzanego urządzenia a więc w pełnym zakresie zmiany prędkości i obciążenia silnika hydraulicznego oraz lepkości zastosowanego czynnika roboczego. Dotyczy to zarówno określania strat i sprawności maszyn wyporowych (pompy i silnika hydraulicznego) zastosowanych w układzie...