Filtry
wszystkich: 1232
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLYMERIC POROUS MEMBRANE
-
A method for evaluating durability of porous slide bearings
PublikacjaThe article presents the structures of porous bearings bushes and greasy lubricants, and the similarity criterion resulting from this structures. A phisical model is proposed which describes the operation of the porous slide bearing bush taking into account, via analogy, the phenomena taking place in the grease lubricant nodes instead of those observed in the bush structures.Included are the result of experimental tests of three...
-
Current advances in membrane processing of wines: A comprehensive review
PublikacjaBackground Membrane-based operations, especially pressure-driven membrane operations, are today well-established procedures for various applications in the wine industry thanks to their intrinsic properties and undoubted advantages over traditional methods. Emerging membrane processes, such as pervaporation, electrodialysis and osmotic distillation, forward osmosis, membrane contactors, offer new and interesting perspectives to...
-
Separation of toluene from gas phase using supported imidazolium ionic liquid membrane
PublikacjaInvestigation on utilization of supported ionic liquids membranes for hydrocarbon separation from the gas phase was performed. Properties of membrane phase, wettability of supports, swelling effects and solubility of toluene were taken into account. Toluene permeation rates were significantly higher than those of pure nitrogen, the selectivity in a range of 17–341 was satisfying for separation. Despite the increase of viscosity...
-
Advanced Porous Materials
Czasopisma -
3D porous graphene-based structures- synthesis and applications
PublikacjaPorous carbon-based materials are of the great industrial and academic interest due to their high surface area, low density, good electrical conductivity, chemical inertness and low cost of fabrication. Up to now, the main approach to obtain porous carbon structures has involved the pyrolysis of carbonaceous natural or synthetic precursors. After the isolation of graphene, the interest in 3D porous graphene-based structures (called...
-
Food Bioactive Ingredients Processing Using Membrane Distillation
PublikacjaSeparation processes are an important part of today’s food industries, especially in the case of specific bioactive components due to their health benefits. In general, processing of bioactive food ingredients assumes the introduction of integrated system directed to their separation, fractionation, and recovery. Recently, membrane distillation (MD) has been considered as an alternative membrane-based separation and concentration...
-
Behaviour of Asymmetric Structure with Base Isolation Made of Polymeric Bearings
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. Due to randomness of earthquake occurrence, lack of visible causes and their power of destructiveness, structural engineers need to develop new technical solutions and protection systems against...
-
A review: Fabrication of porous polyurethane scaffolds
PublikacjaThe aim of tissue engineering is the fabrication of three-dimensional scaffolds that can be used for the reconstruction and regeneration of damaged or deformed tissues and organs. A wide variety of techniques have been developed to create either fibrous or porous scaffolds from polymers, metals, composite materials and ceramics. However, the most promising materials are biodegradable polymers due to their comprehensive mechanical...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublikacjaThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Hydroxyapatite coatings on porous ti and ti alloys
PublikacjaDeposition of hydroxyapatite coating on porous Ti and Ti alloys with electrochemical and biomimetic deposition approach is presented. The enhancement of phosphates deposition by well oriented and uniform titanium oxide nanotube array on the surface of titanium substrate is discussed.
-
Fouling in direct contact membrane distillation process
Publikacja -
Osmotic MD and other membrane distillation variants
Publikacja -
Long-term performance of membrane distillation process
Publikacja -
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublikacjaThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublikacjaResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublikacjaThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Modifiers for Medical Grade Polymeric Systems used in FDM 3D Printing - Short Review
PublikacjaFDM 3D printing could find an application in the wide range of biomedical applications. Unfortunately, the quantity of polymeric biomaterials suitable to processing into filaments is limited. The most frequently used biomaterials for medical constructs such as bone grafts, soft tissue scaffolds or another DDS include PCL, PLA, PVA, HPC, EVA copolymer, EC and TPUs. Various modifiers such as TCP, HA, TEC, MMC could be applicated...
-
Preparation, characterization, and manufacturing of new polymeric materials for 3D printing for medical applications
PublikacjaThis work concerns the synthesis, formation, and characteristics of new filaments for 3D printing in FDM™/FFF technology for medical purposes. Two types of filaments were developed, i.e. degradable polyurethane and biodegradable polylactide-starch. The influence of the 3D printing process on selected filament properties was investigated. A detailed analysis of the filament formation process by the extrusion method was carried out,...
-
Polymeric materials in medicine – structure and desing 2023/24
Kursy Online -
Electrochemicalsynthesis of 3D nano-/micro-structured porous polypyrrole
PublikacjaIn this work, electrosynthesis of electroactive, 3D nano-/micro-structured porous polypyrrole film is presented. The PPy film was synthesized potentiostatically in a one-step process from aqueous solution of pyrrole and lithium perchlorate. The growth mechanism of such structure included: the formation of typical globular PPy film, followed by the formation of the PPy fibers, which then took part in the formation of 3D highly porous...
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublikacjaIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
Application of membrane distillation process for tap water purification
Publikacja -
YSZ Thin film deposited on porous substrate by spray pyrolysis
PublikacjaIn this work the results of deposition of YSZ layer on a porous substrate using an ultrasonic Spray Pyrolysis are presented.
-
Quantification of Compatibility Between Polymeric Excipients and Atenolol Using Principal Component Analysis and Hierarchical Cluster Analysis
PublikacjaAn important challenge to overcome in the solid dosage forms technology is the selection of the most biopharmaceutically efficient polymeric excipients. The excipients can be selected, among others, by compatibility studies since incompatibilities between ingredients of the drug formulations adversely affect their bioavailability, stability, efficacy, and safety. Therefore, new, fast, and reliable methods for detecting incompatibility...
-
Bioactive core material for porous load-bearing implants
PublikacjaSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Modeling bioaugmentation with nitrifiers in membrane bioreactors
PublikacjaBioaugmentation with nitrifiers was studied using two pilot-scale membrane bioreactors, with the purpose of assessing the suitability of state-of-the-art activated sludge models (ASMs) in predicting the efficiency of bioaugmentation as a function of operating conditions. It was demonstrated that the temperature difference between seeding and seeded reactors (ΔT) affects bioaugmentation efficiency. Experimental data were accurately...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Study of NaCl permeability through a non-porous polypropylene film
Publikacja -
MOLECULAR MEMBRANE BIOLOGY
Czasopisma -
Membranes and Membrane Technologies
Czasopisma -
Journal of Membrane Computing
Czasopisma -
Sebastian Lech Wachowski dr inż.
OsobyUrodziłem się w 1987 roku w Bydgoszczy. W 2007 roku ukończyłem Technikum Elektroniczne przy Zespole Szkół Elektroniczych w Bydgoszczy uzyskując tytuł zawodowy technika elektronika. W tym samy roku przeniosłem się do Gdańska gdzie rozpocząłem studnia na kierunku Fizyka Techniczna ze spec. Nanotechnologia na Wydziale Fizyki Technicznej i Matematyki Stosowanej Politechniki Gdańskiej. W 2011 uzyskuję tytuł inżyniera z wyróżnieniem...
-
Integrated membrane bioreactors modelling: A review on new comprehensive modelling framework
PublikacjaIntegrated Membrane Bioreactor (MBR) models, combination of biological and physical models, have been representing powerful tools for the accomplishment of high environmental sustainability. This paper, produced by the International Water Association (IWA) Task Group on Membrane Modelling and Control, reviews the state-of-the-art, identifying gaps for future researches, and proposes a new integrated MBR modelling framework. In...
-
Membrane cleaning and pretreatments in membrane distillation – a review
Publikacja -
Membrane distillation of NaCl solution containing natural organic matter
Publikacja -
The study of membrane distillation used for separation of fermenting glycerol solutions
Publikacja -
Contribution to the mechanism of liquid membrane oscillators involving cationic surfactant.
PublikacjaIt is shown that liquid membrane oscillators with cationic surfactants havemore complex oscillation patterns than observed previously. The actual details of the oscillations depend strongly on the nature of the membrane material, dislosing even the presence of parallel molecular events. It appearsthat sampling topology also has a great influence on the observed oscillato-ry behaviour. Variation of oscillation patterns with...
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Zirconia-based mixed potential sensor with Pt electrode prepared by spin-coating of polymeric precursor
PublikacjaMany types of yttria-stabilized zirconia (YSZ) based gas sensors have been explored extensively in recent years. Great attention have been directed to mixed-potential-type gas sensors. It is due to growing concerns with environmental issues. Not without a significance is the fact of very attractive performance of this type of sensor allowing to detect low concentration of pollutant gases. In this paper two types of YSZ based mixed-potential...
-
Glass-ceramic joining of Fe22Cr porous alloy to Crofer22APU: interfacial issues and mechanical properties
PublikacjaThis work deals with the joining of porous Fe22Cr ferritic stainless steel to a dense Crofer22APU plate by using a silica-based, Ba-containing glass-ceramic. The chemical and interfacial stability and the mechanical properties of the joints were evaluated before and after thermal ageing at 700 ◦C for 500hrs. The sintering behaviour of the glass was assessed by using heating stage microscopy (HSM) to study the influence of a porous...
-
Highly porous nanoberyllium for X-ray beam speckle suppression
PublikacjaThe speckle suppressor device containing highly porous nanoberyllium is proposed for manipulating with the spatial coherence length and removing undesirable speckle structure during the imaging experiments. We report a special device called the speckle suppressor, which contains the highly porous nanoberyllium plate, compacted from both sides by two beryllium windows. By insertion the speckle suppressor in the X-ray beam it allows...
-
How to make membrane distillation greener? A review on environmentally friendly and sustainable aspects
PublikacjaThere is an urgent need for the development of new water resources in order to solve the problem of the world’s growing demand for clean water. Membrane distillation (MD) is a promising alternative to conventional seawater desalination. Although MD itself is often defined as sustainable desalination technology, there are many aspects within the membrane manufacture and process operation that make it far from being green. For instance,...
-
Osmotic membrane distillation with continuous regeneration of stripping solution by natural evaporation
Publikacja -
Membrane separation processes for the extraction and purification of steviol glycosides: an overview
PublikacjaSteviol glycosides (SGs), as natural sweeteners from Stevia rebaudiana, are currently employed for replacing sugar and its derivatives in several food products and formulations. Such compounds play an essential role in human health. Their usage provides a positive effect on preventing diseases related to sugar consumption, including diabetes mellitus, cancer, and lipid metabolism disorders. The traditional extraction of SGs is...
-
The emissions of monoaromatic hydrocarbons from small polymeric toys placed in chocolate food products
PublikacjaThe article presents findings on the emissions of selected monoaromatic hydrocarbons from children's toys placed in chocolate food products. The emission test system involved the application of a new type of microscale stationary emission chamber, μ-CTE™ 250. In order to determine the type of the applied polymer in the manufacture of the tested toys, Fourier transform infrared spectroscopy and thermogravimetric analysis coupled...
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublikacjaBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Membrane technologies assisting plant-based and agro-food by-products processing: A comprehensive review
PublikacjaBackground Nowadays, membrane-based technologies (e.g. microfiltration, ultrafiltration, nanofiltration, membrane distillation, and pervaporation) have demonstrated to meet the requirements to be involved in different food and bioproduct processes. Scope and approach Several applications have been developed, including either separation, recovery or concentration of bioactive molecules from agro-food products and by-products,...
-
High temperature corrosion resistance of porous hastelloy alloy
PublikacjaTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...