Wyniki wyszukiwania dla: closed crack, closed delamination, nonlinearity, crack detection methods
-
Size and mass minimization of capacitor bank in a power converter DC line of DC drive with closed loop control system with PWM and current limitation
PublikacjaPaper deals with evaluation equations for power filter of AC-DC power converter which allows to provide size and mass minimization of capacitor bank in DC drive closed loop systems with PWM and current limitation. Reliability of provided equations is proved by simulation in MATLAB/Simulink
-
Detection of delamination in multi layer composite beams.
PublikacjaW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Compensation of supply current harmonics, reactive power, and unbalanced load current balance in the closed-loop control of a shunt active power filter
PublikacjaThis paper presents the compensation tasks performed by a shunt active power filter, including compensation of harmonic currents, reactive power, and an unbalanced load current. The paper demonstrates novel control of the shunt active power filter in a closed-loop system. The control algorithm was verified by performing simulations and compared the simulated results with those obtained in an open-loop control system. All simulations...
-
Closed-Loop Control System Design for Wireless Charging of Low-Voltage EV Batteries with Time-Delay Constraints
PublikacjaThis paper presents an inductive power transfer system on the basis of a double single- phase three-level T-type inverter and two split transmitting coils for constant current and constant voltage wireless charging of low-voltage light electric vehicle batteries with closed-loop control, considering time-delay communication constraints. An optimal control structure and a modified control strategy were chosen and implemented to...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublikacjaThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Crack identification using wavelets on experimental staticdeflection profiles
PublikacjaArtykuł prezentuje metodę lokalizacji uszkodzeń w belce wspornikowej za pomocą transformaty falkowej statycznej linii ugięcia. Efektywnośc proponowanej techniki jest sprawdzona na podstawie badań eksperymentalnych. Do pomiaru statycznej linii ugięcia proponuje się metodę fotogrametryczną.
-
Numerical assessment of the fatigue crack propagation in ship structuraldetails.
PublikacjaPrzedstawiono podejście teoretyczne pozwalające na modelowanie rozwoju pęknięcia w konstrukcji kadłuba okrętu. Omówiono założenia i procedurę realizacyjną. Pokazano wyniki badań rzeczywistych modeli konstrukcji kadłuba-skrzyżowanie wiązań ramowych o jednakowej wysokości. Dokonano porównania i krytycznej analizy wyników uzyskanych na drodze teoretycznej z wynikami badań rzeczywistych.
-
Crack Resistance of Asphalt Concrete Subjected to Environmental Factors
PublikacjaThe paper presents an analysis of the influence of environmental factors on the cracking susceptibility of asphalt concrete resulting in a change in the durability of asphalt pavement. In order to assess the phenomenon, laboratory tests were carried out taking into account the destructive effects of moisture, freeze-thaw cycle and long-term ageing. The influence of both factors occurring simultaneously was also verified. Due to...
-
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublikacjaIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Crack monitoring in concrete beams under bending using ultrasonic waves and coda wave interferometry: the effect of excitation frequency on coda
PublikacjaConcrete is one of the most widely used construction materials in the world. In recent years, various non-destructive testing (NDT) and structural health monitoring (SHM) techniques have been investigated to improve the safety and control of the current condition of concrete structures. This study focuses on micro-crack monitoring in concrete beams. The experimental analysis was carried out on concrete elements subjected to three-point...
-
Full wavefield processing by using FCN for delamination detection
Publikacja -
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Longitudinal wave propagation. Part II—Analysis of crack influence
Publikacja -
Crack identification using wavelets on experimental static deflection profiles
Publikacja -
Longitudinal wave propagation. Part II, Analysis of crack influence
PublikacjaW pracy analizowano wpływ pęknięć zmęczeniowych na propagacje fali wzdłużnej w prętach. Opracowano nowe typy element ów spektralnych oparte na teorii elementarnej, Love'a, Mindlina i trójpostaciowej.
-
The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels
PublikacjaIn this study, the fractal dimension of fatigue fracture surfaces is investigated in order to find an alternative failure loading indicator. Some of many metrological factors are generalized by reducing the fracture surface structure to one factor and develop an entire fracture surface procedure by analyzing the impact of surface slope and calculation resolution. Three notched geometries are studied under cyclic bending-torsion:...
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublikacjaFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Differences in sequences between HBV-relaxed circular DNA and covalently closed circular DNA
Publikacja -
Closed-form expression for the magnetic shielding constant of the relativistic hydrogenlike atom in an arbitrary discrete energy eigenstate: Application of the Sturmian expansion of the generalized Dirac–Coulomb Green function
PublikacjaWe present analytical derivation of the closed-form expression for the dipole magnetic shielding constant of a Dirac one-electron atom being in an arbitrary discrete energy eigenstate. The external magnetic field, by which the atomic state is perturbed, is assumed to be weak, uniform, and time independent. With respect to the atomic nucleus we assume that it is pointlike, spinless, motionless, and of charge Ze. Calculations are...
-
Radiation Detection Technology and Methods
Czasopisma -
Faults and Fault Detection Methods in Electric Drives
PublikacjaThe chapter presents a review of faults and fault detection methods in electric drives. Typical faults are presented that arises for the induction motor, which is valued in the industry for its robust construction and cost-effective production. Moreover, a summary is presented of detectable faults in conjunction with the required physical information that allow a detection of specific faults. In order to address faults of a complete...
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publikacja -
The crack surface morphology investigation of S355J2 steel after bending-torsion fatigue
Publikacja -
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension.
PublikacjaW artykule przedstawiono wyniki numerycznej obliczenia rozstawu rys w pręcie żelbetowym poddanemu rozciąganiu. Obliczenia wykonano przy zastosowaniu sprężysto-plastycznego modelu rozszerzonego o długość charakterystyczna mikrostruktury przy pomocy teorii nielokalnej.
-
Thermodynamic Analysis of a Closed-Cycle Ocean Thermal Energy Conversion Power Plant for Offshore Platforms
Publikacja -
Seasonal changes in organotin compounds in water and sediment samples from the semi-closed Port of Gdynia
PublikacjaThe effect of seasonal changes on the distribution of organotin compounds (OTC) in the sediments and seawaterfrom the docks of the Port of Gdynia was investigated. Sediment and seawater samples were collectedfrom four industrial docks in February (winter) and June (summer) in 2009. The samples were analyzed forbutyltin, phenyltin, octyltin, and tricyclohexyltin (total of 9 OTC derivatives). The fine fraction (b0.063 mm)accumulated...
-
Magnetic and infrared thermography methods in detection of antipersonnel landmines
PublikacjaIn this paper the two alternative methods of antipersonnel landmine detection are shown: the magnetic method and the active infrared thermography. The experimental results of the detection of selected, plastic mines using both methods are also presented.
-
Closed Form Constraint Equations Used to Express Frictionless Slip of Multibody Systems Attached to Finite Elements—Application to a Contact between a Double Pendulum and a Beam
PublikacjaThis paper focuses on the numerical modeling of the dynamics of mechanical systems. Robots that can inspect high-voltage lines inspired this research. Their control systems must anticipate potential grab positions appropriately. We intend to formulate equations dedicated to the numerical description of the robot/cable contact. The investigated problem is not straightforward, since parts of the modeled systems are numerically inhomogeneous....
-
Prediction of corrosion fatigue crack propagation life for welded joints under cathodic potentials
PublikacjaPrzy ochronie katodowej poniżej potencjału optymalnego obserwuje się przyspieszenie propagacji pęknięcia korozyjno-zmęczeniowego w porównaniu do konstrukcji nie chronionej. Zaproponowano własną formułę empiryczną na wpływ potencjału ochronnego na prędkość propagacji pęknięcia oraz własny wzór na [delta]K w złączu pachwinowym. Wyprowadzono wzór na krzywą ''S-Np'' (naprężenie - długość okresu propagacji pęknięcia). Zaprezentowana...
-
Minimal number of periodic points for smooth self-maps of two-holed 3-dimensional closed ball
PublikacjaDla ciągłego odwzorowania f przestrzeni określonej w tytule w siebie, które posiada rzeczywiste wartości własne na drugiej grupie homologii, wyznaczona została minimalna liczba punktów r-periodycznych w klasie wszystkich gładkich odwzorowań homotopijnych z f.
-
Closed forms of the Green's function and the generalized Green's function for the Helmholtz operator on the N-dimensional unit sphere
PublikacjaPokazano, że funkcję Greena dla operatora Helmholtza na N-wymiarowej sferze jednostkowej można wyrazić przez funcję Gegenbauera pierwszego rodzaju. W tych przypadkach, w których funkcja Greena nie istnieje, skonstruowano uogólnioną funkcję Greena.
-
Closed-Loop Control System Design for Wireless Charging of Low-Voltage EV Batteries with Time-Delay Constraints
Publikacja -
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublikacjaThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
FE-investigations on crack spacing in reinforced concrete beams within non-local continuum mechanics.
PublikacjaW artykule przedstawiono wyniki numerycznej analizy rozstawu rys w belkach żelbetowych przy zastosowaniu dwóch ciągłych modeli nielokalnych. Zbadano wpływ wielu różnych parametrów na rozstaw rys.
-
Spectral Methods for Modelling of Wave Propagation in Structures in Terms of Damage Detection—A Review
PublikacjaModern methods of detection and identification of structural damage direct the activities of scientific groups towards the improvement of diagnostic methods using for example the phenomenon of mechanical wave propagation. Damage detection methods that use mechanical wave propagation in structural components are extremely effective. Many different numerical approaches are used to model this phenomenon, but, due to their universal...
-
Experimental verification and comparison of mode shape-based damage detection methods
PublikacjaThis paper presents experimental verification and comparison of damage detection methods based on changes in mode shapes such as: mode shape curvature (MSC), modal assurance criterion (MAC), strain energy (SE), modified Laplacian operator (MLO), generalized fractal dimension (GFD) and Wavelet Transform (WT).
-
Phosphorus removal by application of natural and semi-natural materials for possible recovery according to assumptions of circular economy and closed circuit of P
PublikacjaIn the last fewyears the idea of circular economy has become essential. Thus, designing methods of nutrients removal should be based on usingmaterials that make it possible to recover those nutrients. Recently,methods applied in wastewater treatment plants cannot provide optimal results; moreover, the application of commercial coagulants like ferric chloride and polyaluminumchloride can cause difficulties in potential recovery...
-
Propagacja fali wzdłużnej w pręcie z pęknieciem poprzecznym. Longitudinal wave propagation in a rod with a transverse crack.
PublikacjaW pracy przedstawiono wyniki analizy propagacji fali wzdłuznej w pręcie z pęknięciem poprzecznym.
-
The Unrestricted Global effort to complete the Closed Or Open after Source Control Laparotomy for Severe Complicated Intra-Abdominal Sepsis (COOL) Trial
Publikacja -
Performance Analysis of Machine Learning Methods with Class Imbalance Problem in Android Malware Detection
PublikacjaDue to the exponential rise of mobile technology, a slew of new mobile security concerns has surfaced recently. To address the hazards connected with malware, many approaches have been developed. Signature-based detection is the most widely used approach for detecting Android malware. This approach has the disadvantage of being unable to identify unknown malware. As a result of this issue, machine learning (ML) for detecting malware...
-
Detection methods of dynamic spammer's behavior
PublikacjaPoczta elektroniczna ze względu na swoją naturę jest bardzo podatna na zjawisko spamu. Oddzielanie spamu od dobrych wiadomości jest zadaniem żmudnym i pracochłonnym. Dlatego jest rzeczą istotną opracowanie skutecznej metody walki ze spamem uwzględniającej nie tylko aktualne metody działania spamerów, ale również wzięcie pod uwagę dynamicznych aspektów zmieniających się stale ich zachowań.Artykuł opisuje metodę klasyfikacji wiadomości...
-
Anomaly Detection in Railway Sensor Data Environments: State-of-the-Art Methods and Empirical Performance Evaluation
PublikacjaTo date, significant progress has been made in the field of railway anomaly detection using technologies such as real-time data analytics, the Internet of Things, and machine learning. As technology continues to evolve, the ability to detect and respond to anomalies in railway systems is once again in the spotlight. However, railway anomaly detection faces challenges related to the vast infrastructure, dynamic conditions, aging...
-
Energy requirements for methods improving gas detection by modulating physical properties of resistive gas sensors
PublikacjaAbstract. One of the most important disadvantage of resistive gas sensors is their limited gas selectivity. Therefore, various methods modulating their physical properties are used to improve gas detection. These methods are usually limited to temperature modulation or UV light irradiation for the layers exhibiting photocatalytic effect. These methods cause increased energy consumption. In our study we consider how much energy...
-
Ograniczenie trwałości skojarzeń ceramicznych w wyniku propagacji pęknięć powierzchniowych = Fatigue life limitation of ceramic materials due to surface crack propagation
PublikacjaPrzedstawiono krótką analizę literaturową dotyczącą mechanizmów propagacji pęknięć w materiałach ceramicznych oraz wyniki dotychczasowych badań doświadczalnych wybranych materiałów ceramicznych z uwzględnieniem wpływu pęknięć powierzchniowych na trwałość ceramicznych skojarzeń tocznych.
-
Methods of non-stationary components detection of random fluctuations
PublikacjaPrzedstawiono problem detekcji składowych niestacjonarnych dla kilku rodzajów sygnałów losowych reprezentujących zjawiska szumowe w systemach fizycznych. Zaproponowano zastosowanie kilku specyficznych metod detekcji na podstawie analizy w dziedzinie częstotliwości i przedyskutowano uzyskane wyniki potwierdzające efektywność tych metod. Bardziej złożona obliczeniowo metoda z zastosowaniem transformaty falkowej daje lepsze rezultaty...
-
Review of Segmentation Methods for Coastline Detection in SAR Images
PublikacjaSynthetic aperture radar (SAR) images acquired by airborne sensors or remote sensing satellites contain the necessary information that can be used to investigate various objects of interest on the surface of the Earth, including coastlines. The coastal zone is of great economic importance and is also very densely populated. The intensive and increasing use of coasts and changes of coastlines motivate researchers to try to assess...
-
Damage detection in turbine wind blades by vibration based methods
PublikacjaThe paper describes results of numerical simulation for damage localization in the composite coat of a wind turbine blade usingmodal parameters and a modern damage detection method (wavelet transform).