Wyniki wyszukiwania dla: CHEMICAL INSTALLATION TEMPERATURE CONTROL
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
Stability analysis of a road scarp in the Carpathian Mountains and methods of its protection
PublikacjaThe purpose of the study was to analyse the stability of a road scarp endangered by a landslide and to consider some measures for its stabilization. The potential landslide could unfavourably alter the shape of the slope, thus a religious sanctuary situated above the slope. The present research has resulted in suggestions of possible protection methods, namely, drainage, soil nailing, installation of piles, supporting the scarp...
-
Simplified simulation technique of rotating, induction heated, calender rolls for study of temperature field control
Publikacja -
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublikacjaIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublikacjaThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Gaseous products from scrap tires pyrolisis
PublikacjaIn European Union 75% of used tires should be recycled. The most common method of used tires disposal, is burning in cement kilns, which does not solve the problem. Pyrolysis process can be an alternative way of utilization of tires. The aim of the researches was to check the influence of pyrolysis products (gas and oil fractions) on environment. Samples from pyrolysis process, like light oil fractions or pyrolysis gases were analyzed...
-
Multiuser Stereoscopic Projection Techniques for CAVE-Type Virtual Reality Systems
PublikacjaDespite the development of increasingly popular head mounted displays, CAVE-type systems may still be considered one of the most immersive virtual reality systems with many advantages. However, a serious limitation of most CAVE-type systems is the generation of a three-dimensional (3-D) image from the perspective of only one person. This problem is significant because in some applications, the participants must cooperate with each...
-
Strength analysis of the support structure of the offshore wind turbine
PublikacjaThe global power demand from renewable sources is growing. One of a very favorable solution which meets severe environmental protection requirements are the offshore wind turbines. The offshore wind energy sector has experienced very fast development over last decade. Offshore wind farms, in comparison with onshore applications, can provide increased efficiency with reduced noise, visual, transportation and installation con-flicts....
-
Evaluation Of Single Pole Auto-Reclosing Effectiveness With Nonlinear Secondary Arc Model
PublikacjaThe paper discusses two evaluation methods of single pole auto-reclosing process effectiveness in HV transmission lines. Secondary arc current and recovery voltage results obtained by load flow calculation are compared to the results obtained by the time domain simulations. Moreover, a non-linear secondary arc implementation is presented. The authors indicate, that precise representation of secondary electric arc leads to more...
-
Chemical Control of SrLi(Al1–xGax)3N4:Eu2+ Red Phosphors at Extreme Conditions for Application in Light-Emitting Diodes
Publikacja -
Signals Features Extraction in Radioisotope Liquid-Gas Flow Measurements using Autocorrelation Function
PublikacjaKnowledge of the two-phase flow structure is essential for the proper conduct of industrial processes. Description of liquid-gas flow regimes is possible by using of data analysis in time, frequency, or state-space domain. In this research studies, the autocorrelation function is applied for analysis of signals obtained for liquid-gas flow by use gamma-ray absorption. The experiments were carried out on the laboratory hydraulic...
-
As- built inventory of the office building with the use of terrestrial laser scanning
PublikacjaTerrestrial Laser Scanning (TLS) is an efficient tool for building inventories. Based on the red- laser beam technology it is possible to provide the high accuracy data with complete spatial information about a scanned object. In this article, authors present the solution of use a TLS in as-built inventory of the office building. Based on the provided data, it is possible to evaluate the correctness of built details of a building...
-
Automatic Analysis of Trajectories of Moving Objects
PublikacjaOngoing monitoring is essential to providing security and safety of maritime and air operations. This paper presents the research in the area of automatic analysis of movement of unrestricted vehicles like ships and air-planes. The analysis is aimed at extraction of trajectory information, and the results can be used to identify anomalous behaviour in archived and real-time data. In this paper we focus on data acquired using the...
-
Wireless paging system
PublikacjaAssistance to patients at hospitals and nursing homesoften encounters problems related to obtaining information onthe current needs of the patient. Traditionally, patient informshospital stuff by wire and wireless paging systems. WirelessPaging Systems allow one to overcome the limitations of theirwire counterparts, which include high installation costs (cabling)and lack of patient mobility. The main difference betweenpresented...
-
Foundations of Grid Processing Architecture for the Comcute System
PublikacjaFundamental system algorithms and structures implemented in the Comcute system are described and analysed in detail. Layered architecture of the system model is highlighted. System tasks of the layers are elaborated, presented and described. Operational details of communication interfaces among layers are worked out and examined. The focus is put onto implemented system components with regard to their operability and efficiency....
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
Shading, Dusting and Incorrect Positioning of Photovoltaic Modules as Important Factors in Performance Reduction
PublikacjaThe amount of solar radiation reaching the front cover of a photovoltaic module is crucial for its performance. A number of factors must be taken into account at the design stage of the solar installation, which will ensure maximum utilization of the potential arising from the location. During the operation of a photovoltaic installation, it is necessary to limit the shading of the modules caused by both dust and shadowing by trees...
-
PARAMETRIC ANALYSIS OF THE EFFICIENCY OF THE COMBINED GAS-STEAM TURBINE UNIT OF A HYBRID CYCLE FOR THE FPSO VESSEL
PublikacjaA thermal diagram of the combined gas‒steam turbine unit of a hybrid cycle, which is an energy complex consisting of a base gas turbine engine with a steam turbine heat recovery circuit and a steam-injected gas turbine operating with overexpansion, is proposed. A mathematical model of a power plant has been developed, taking into consideration the features of thermodynamic processes of simple, binary, and steam-injected...
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublikacjaThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Parallel computations in the volunteer based Comcute system
PublikacjaThe paper presents Comcute which is a novel multi-level implemen- tation of the volunteer based computing paradigm. Comcute was designed to let users donate the computing power of their PCs in a simplified manner, requiring only pointing their web browser at a specific web address and clicking a mouse. The server side appoints several servers to be in charge of execution of particular tasks. Thanks to that the system can survive...
-
Stability Analysis of the Floating Offshore Wind Turbine Support Structure of Cell Spar Type During its Installation
PublikacjaThe article presents the results of selected works related to the wider subject of the research conducted at the Faculty of Ocean Engineering and Ship Technology of the Gdansk University of Technology, which concerns design and technology of construction, towing, and settlement on the seabed, or anchoring, of supporting structures for offshore wind farms. As a result of this research, several designs of this type of objects were...
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublikacjaAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
Voltage profiles improvement in a power network with PV energy sources – results of a voltage regulator implementation
PublikacjaThe constant increase in the number of photovoltaic (PV) energy sources in distribution networks is the cause of serious voltage problems. The networks built at least a dozen years ago are not provided for the installation of a large number of micro-sources. It happens that the previously properly functioning power networks are not able to provide to consumers power with the required parameters, after installing many PV sources....
-
The Lost Kinetic Architecture and How to Reintroduce it in the Landscape – The Case Study of the Drainage Windmills in the Vistula Delta
PublikacjaRecreating the lost kinetic landscape of the Vistula Delta is a considerable challenge. The study aims to propose a method for reproducing windmills and their effect on the landscape. The paper suggests a method based on the transposition of the forms of movement from windmills historically present in the region to modern forms. The method is based on a series of analyses starting with the study of the region and its history followed...
-
Centrifugal magnetic fluid seals
PublikacjaSeals perform an important and at times overlooked function in a lubricant system. They prevent or minimize the movement of the lubricant between two surfaces and also minimize the level of contamination in the system. Seals are divided into static and dynamic types. Static seals operate in systems where the mating surfaces do not move relative to each other. In contrast, dynamic seals operate under conditions where the mating surfaces...
-
Laboratory assessment of permeability of sand and biopolymer mixtures
PublikacjaLaboratory assessment of permeability of sand and biopolymer mixtures. This research presents a method of creating seepage barriers in a sandy soil using biopolymer additives (biosubstance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The paper aims to investigate the infl uence of a biosubstance employed in a highly permeable sandy soil. Amount of the...
-
Lightweight glass and metal roof structures in the 19th century. Architecture and construction.
PublikacjaThe 19th century brought new construction possibilities. The usage of metal elements in mesh structures, filled in with glass, resulted in creating entirely new types of objects. They have distinguished themselves in architecture and technical solutions. The envelope structures giving spatial interiors were arising very quickly. They have been enabling large light penetration, triggering them extremely bright. Thus these building...
-
Load testing of a suspended footbridge in Radom (Poland)
PublikacjaThe footbridge in Radom is a suspended bridge of an interesting architectural form. The structure was de-signed for 4 kN/m2 of crowd loading. Dynamic calculations were not included in the design. The structure’s acceptance tests took place on the 14th of October 2016. The behaviour of the footbridge in static testing met the expectations. Unfortunately, as a result of dynamic tests, dangerous behaviour of the footbridge was revealed....
-
LabVIEW-based intelligent system of protection against electric shock for photovoltaic installations
PublikacjaEvaluation of shock hazard in installations with photovoltaic sources of energy is more complicated than in a conventional low voltage system. In case of earth fault in photovoltaic generators, that are connected to the AC power public grid, a composite waveform of earth fault current in the installation may occur. For composite waveforms, the safety criteria should be modified. The paper considers the effect of the composite waveforms...
-
Dynamic Signal Strength Mapping and Analysis by Means of Mobile Geographic Information System
PublikacjaBluetooth beacons are becoming increasingly popular for various applications such as marketing or indoor navigation. However, designing a proper beacon installation requires knowledge of the possible sources of interference in the target environment. While theoretically beacon signal strength should decay linearly with log distance, on-site measurements usually reveal that noise from objects such as Wi-Fi networks operating in...
-
The Impact of Ergonomic Guiding Principles on the Formation of Modern Monumental Art
PublikacjaCommemoration of historic events is now a commonplace phenomenon both in culture and in academic research. The phenomenon is linked to an increase in the representation of the visualisation of the past in public sphere, which in turn leads to reformulation of monumental art. Modern monuments are often spatial forms consisting both of sculpture installation and bigger constructions. In case of these realisations, the designers,...
-
Methodology for assessing the lighting of pedestrian crossings based on light intensity parameters
PublikacjaOne of the possible preventive measures that could improve safety at crossings is to assess the state of illumination of the lighting installation located in the transition area for pedestrians. The City of Warsaw has undertaken to comprehensively assess the pedestrian crossings to determine the level of road safety and the condition of lighting. The lighting conditions related to pedestrian crossings without traffic lights in...
-
Pyrolysis Process of Whole Waste Tires as a Biomass Energy Recycling
PublikacjaThe article is devoted to the description of material recycling of whole waste tires, including a new method of pyrolysis process, resulting in the final products: technically oil fractions (rubber plasticizer of rubber compounds) or diesel fuels (light, medium and heavy), activated carbon, gas fuel and steel scrap. Operational and performance tests of the first version of the pilot plant, consisting of three contributions cooperating...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublikacjaOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublikacjaThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking these...
-
Signals features extraction in radioisotope liquid-gas flow measurements using wavelet analysis
PublikacjaKnowledge of the structure of a flow is significant for the proper conduct of a number of industrial processes. In this case, a description of a two-phase flow regimes is possible by use of the time-series analysis in time, frequency and state-space domain. In this article the Discrete Wavelet Transform (DWT) is applied for analysis of signals obtained for water-air flow using gamma ray absorption. The presented method was illustrated...
-
The role of numerical tests in assessing road restraint system functionality
PublikacjaKey to understanding the needs and building road infrastructure management tools to prevent and mitigate run-off-road accidents is to identify hazards and their sources which are a result of wrong design, construction, and installation of road restraint systems. Building such tools requires advanced studies with field tests, simulations and models to demonstrate the effects of selected parameters on road user safety. The research...
-
CFD-based evaluation of current-carrying capacity of power cables installed in free air
PublikacjaEvaluation of current-carrying capacity of power cables and selection of cross-sectional area of their conductors are mainly performed in accordance with requirements of EN, IEC or IEEE standards. However, these standards do not provide all methods of cables installation and location which occur in practice. Thus, in some cases, performance of advanced modeling of various thermal phenomena, affecting power cables current-carrying...
-
Recycling of raw materials, silicon wafers and complete solar cells from photovoltaic modules
PublikacjaPhotovoltaic modules (PVs) are an attractive way of generating electricity in reliable and maintenance-free systems with the use of solar energy. The average lifetime of photovoltaic modules is 25 to 30 years. To offset the negative impact of photovoltaic modules on the environment, it is necessary to introduce a long-term strategy that includes a complete lifecycle of all system components from the production phase through installation...
-
Chemical treatment of crystalline silicon solar cells as a main stage of pv modules recycling = Obróbka chemiczna krzemowych ogniw słonecznych jako najważniejszy etap w recyklingu modułów fotowoltaicznych
PublikacjaIn recent years, photovoltaic systems have gained worldwide recognition and popularity as a environmentally friendly way of solving energetic problems. However, a problem of utilizing worn out photovoltaic systems, amount of which will rapidly increase in the future, is yet to be solved. Establishing a technology of recycling and reusing obsolete photovoltaic panels is a necessity.Photovoltaic modules in crystalline silicon solar...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublikacjaThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking...
-
PROJECT OF AN TDC SIGNAL DISTRIBUTOR PROTOTYPE WITH GAL-VANIC SEPARATION DESTINED FOR STUDIES OF THE BEGINNING OF SELFIGNITION USING LANGMUIR PROBE
PublikacjaThe knowledge of pistons' TDC is crucial while performing any kind of measurement beneficial to diagnostic inference of a diesel engine. The research of engines under exploitation often cause impartial difficulties with, eg. capability of probe installation. Therefore, it becomes crucial to minimalize those. The paper presents a description of a TDC impulse distributor - divider that provides signal delivery to more than one measurement...
-
Techno-economic evaluation of combined cycle gas turbine and a diabatic compressed air energy storage integration concept
PublikacjaMore and more operational flexibility is required from conventional power plants due to the increasing share of weather-dependent renewable energy sources (RES) generation in the power system. One way to increase power plant’s flexibility is integrating it with energy storage. The energy storage facility can be used to minimize ramping or shutdowns and therefore should lower overall generating costs and CO2 emissions. In this article,...
-
Featured based CAVE software factory
PublikacjaIn the paper we convey the lessons learned along the path we have gone through several years since establishing a room-sized CAVE installation at our university, from craft manufacturing and ad-hoc software reuse of VR software products to the robust feature driven software product line (SPL) implementing the Product Line Engineering (PLE) factory paradigm. With that we can serve all our departments and other entities from the...
-
Vibration-Based Investigation of a Historic Bell Tower to Understand the Occurrence of Damage
PublikacjaABSTRACT The paper presents a survey of the historic Arch-cathedral bell tower in Vilnius induced by the appearance of cracks in the structure after a new bell system installation. An attempt is undertaken to identify the reason for the crack occurrence and to check a possible crack influence on global structural behaviour. The research is based on dynamic measurements made in the tower during ambient vibrations and during vibrations...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublikacjaThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Automation of the Road Gate Operations Process at the Container Terminal—A Case Study of DCT Gdańsk SA
PublikacjaThe future increased terminal capacity will result in more container movement through the road complex and rail siding, which are one of the most critical areas (potential bottlenecks) in the container terminal. Truck turnaround time is one of the major factors that customers take into account while deciding how many container volumes they will handle through the container terminal. To enable to optimize increased traffic with...