Wyszukiwarka
Wyniki wyszukiwania dla: IMPACT TEST
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublikacjaThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
Static load test on concrete pile – instrumentation and results interpretation
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Investigation method of large-volume tire with mobile test rig
PublikacjaThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublikacjaThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublikacjaThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
Flow cytometric approach to evaluate the impact of hydro-technical concrete compounds’ release to the freshwater microbiome
PublikacjaThe aim of this research was to test the potential of applying a flow cytometric procedure to evaluate the impact of concrete compounds’ release to the freshwater microbiome. Cells from the collected samples were stained with a fluorogenic redox indicator dye that measures the redox potential of microbial cells. This novel approach was combined with the assessment of microorganisms’ penetration into the internal structures of concrete...
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublikacjaThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
Mechanical properties of VL E27 steel for shipbuilding – tensile test in -20°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – tensile test in ambient temperature
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – tensile test in 0°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Effect of Body Composition on Respiratory Compensation Point During an Incremental Test
Publikacja -
Stiffness and pre-stretching estimation from indentation test of hyperelastic membrane
Publikacja -
The verification of the estimation of transport and sorption parameters in the MATLAB environment. Column test
Publikacja -
<title>FPGA-based cavity simulator for Tesla test facility</title>
Publikacja -
Load Test of Railway Viaduct Built Using Crosswise Launching Technology
Publikacja -
Determination of the bearing capacity of pile foundations based on CPT test results
PublikacjaAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Evaluation of Thermal Stresses in Asphalt Layers Incomparison with TSRST Test Results
Publikacja -
Comparison of a tribological model and real component test methods for lubricated contacts
Publikacja -
Influence of Silicon Additives on Tribological and Rheological Test Results for Vegetable Lubricants
Publikacja -
Gendered Self-Views Across 62 Countries: A Test of Competing Models
Publikacja -
Bacterial luminescence test screening of highly polluted areas in the Odra River
PublikacjaW pracy przedstawiono wyniki badania ekotoksyczności wód i osadów z dorzecza Odry w obrazie testu z zastosowaniem bakterii Vibrio Fischerii. Badania przesiewowe wskazują, że silnie zanieczyszczone są miejsca w okolicy Brzegu Dolnego, ujścia Nysy Kłodzkiej i Małej Panwi.
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublikacjaThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
Low Power Baseband Processor for M2M Reconfigurable Radio Test Platform
PublikacjaSoftware Defined Radio (SDR) is becoming more andmore frequently used technique for wireless communication. Itfacilitates as fast prototyping and is a versatile method fordeveloping new communication systems. SDR can be realizedbased on high computational capacity platform, where powerconsumption is no a primary concern like i.e. DVB or BTStransmitters. Another trend are low power systems, whereavailable power in reduced and more...
-
Development and test of fex, a fingers extending exoskeleton for rehabilitation and regaining mobility
PublikacjaThis paper presents the design process of an exoskeleton for executing human fingers' extension movement for the rehabilitation procedures and as an active orthosis purposes, together with its first clinical usability tests of a robotic exoskeleton. Furthermore, the Fingers Extending eXoskeleton (FEX) is a serial, under-actuated mechanism capable of executing fingers' extension. FEX is based on the state-of-art FingerSpine serial...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
On the influence of shell element properties on the response of car model in crash test
PublikacjaIt goes without saying that numerical simulations play important role in the modern engineering practice. Contemporary CAD environments combined with FEM solvers, along with computer power of modern processors, give the engineer fast and efficient tool. Ultimately, however it is the user alone who is responsible for the correctness of the results. As long as the FEM calculations remain in the sphere of academic exercise, the inevitable...
-
Comparison of single microjet cooling with water, ethanol and HFE7100 as test fluids
PublikacjaThe paper presents the investigation of a single microjet cooling forming an thin liquid film on the impingement surface of specially designed rig. The basis of microjet technology is to produce laminar jets, which when impinging the surface have a very high kinetic energy at the stagnation point. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm in width....
-
A Test-Bed Analysis of Simultaneous PMIPv6 Handover in 802.11 WLANs Environment
PublikacjaProviding mobility in access networks is a challenge that we have to deal with. Due to networks’ convergence and migration to all-IP networks, mobility management at the network layer is required. However, there is a need for cooperation mechanisms between the network layer and lower layers to support multimedia services and make handover more efficient. This paper presents experimental research on simultaneous handover performance...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublikacjaThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
The relationships between asphalt mix rutting resistance and MSCR test results
PublikacjaW publikacji przedstawiono badania wpływu rodzaju asfaltu na odporność i deformacje. Wykazano, że w przypadku betonów asfaltowych jest lepsza korelacja pomiędzy cechami asfaltów a odpornością na deformacje niż w przypadku mieszanek mineralno-asfaltowych o nieciągłym uziarnieniu.
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublikacjaThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublikacjaA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
A method of Functional Test interval selection with regards to Machinery and Economical aspects
PublikacjaThis paper discusses the problem of choosing the optimal frequency of functional test, including the reliability calculations and production efficiency, but also the effect of company risk management. The proof test as a part of the functional test interval is well described for the process industry. Unfortunately, this situation is not the case for the machinery safety functions with low demand mode. Afterwards, it is presented...
-
The role of low-energy electrons in the charging process of LISA test masses
PublikacjaThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Neurochemical changes underlying cognitive impairment in olfactory bulbectomized rats and the impact of the mGlu5-positive allosteric modulator CDPPB
PublikacjaThe olfactory bulbectomized (OBX) rat model is a well-established model of depression in which antidepressant drugs reverse deficits in the passive avoidance test 14 days after administration. Recently, the olfactory bulbectomized rat model has been proposed to be a model of Alzheimer’s disease (AD), and the available data indicate similarities between the changes that typically occur in AD and those observed in OBX animals. In...
-
The Impact of Thermal Stresses on Volume Resistivity: Performance Comparison between TR-XLPE and XLPE Cables
PublikacjaMost failures in electric power cables are attributed to the development of water trees inside the insulating materials. Thus, the development and utilization of Tree Retardant Cross-Linked Polyethylene (TR-XLPE) based cables have recently been given great attention to overcome the treeing issues. TR-XLPE cables use low-density polyethylene compounds suppressing the formation of water trees while retaining excellent electrical,...
-
Mechanical properties of VL E27 steel for shipbuilding – fracture documentation (test in -20°C)
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture documentation (test in +20°C)
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture documentation (test in 0°C)
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublikacjaThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
Assessment of the Bulgarian Wastewater Treatment Plants’ Impact on the Receiving Water Bodies
PublikacjaDeterioration of water quality is a major problem world widely according to many international non-governmental organizations (NGO). As one of the European Union (EU) countries, Bulgaria is also obliged by EU legislation to maintain best practices in assessing surface water quality and the efficiency of wastewater treatment processes. For these reasons studies were undertaken to utilize ecotoxicological (Microtox®, Phytotoxkit...
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in 0°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in 20°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in -20°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....