wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STAINLESS%20STEEL
-
Multiaxial Fatigue Behaviour of SLM 18Ni300 Steel
PublikacjaFatigue behaviour of SLM 18Ni300 steel under proportional bending-torsion loading is studied. The fatigue tests are conducted under pulsating loading conditions using tubular specimens with a transversal circular hole. Three ratios of the normal stress to shear stress are considered, namely σ/τ=4,σ/τ=2 and σ/τ = 4/3. Crack initiation sites were found for two diametrically opposite points around the hole, whose locations are governed...
-
Underwater Local Cavity Welding of S460N Steel
PublikacjaIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
ENGINEERING JOURNAL-AMERICAN INSTITUTE OF STEEL CONSTRUCTION INC
Czasopisma -
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN
Czasopisma -
Zagrożenia korozyjne stali nierdzewnych w przemyśle spozywczym
PublikacjaPrzedstawiono przyczyny występowania zagrożeń korozyjnych stali nierdzewnych w przemyśle spożywczym. Szczegółowo omówiono mechanizm oraz sposób zapobiegania korozji wżerowej, szczelinowej oraz pękania korozyjnego. Zaprezentowano dokumentację fotograficzną omówionych typów korozji. Wskazano podstawowe problemy związane z doborem materiałów konstrukcyjnych do budowy instalacji w przemyśle spożywczym.
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublikacjaNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublikacjaThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publikacja -
Application of Numerical Simulations on 10GN2MFA Steel Multilayer Welding
Publikacja -
Numerical Simulations of X22CrMoV12-1 Steel Multilayer Welding
Publikacja -
The influence of dimensional accuracy on steel structures cost calculation
PublikacjaW referacie przedstawiono zależność pomiędzy wartością tolerancji a kosztami wytwarzania budowlanych konstrukcji stalowych. Opisano zasady klasyfikacji tolerancji prętowych konstrukcji stalowych z uwagi na porawny montaż konstrukcji wyrażony równaiem pętli montażowej. Przedstawiono podstawy analizy i syntezy tolerancji oraz zaproponowano nową formułę optymalizacji kosztów wytwarzania. Wskazano metody rozwiązania zadania optymalizacyjnego.
-
The effect of the concentration of steel fibres on the properties of industrial floors
Publikacja -
Practical Application of the Industry 4.0 Concept in a Steel Company
Publikacja -
Modification of cement-ash composites with steel fibre addition
PublikacjaPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Fatigue properties of laser welded steel sandwich panel.
PublikacjaPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublikacjaIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Experimental tests of steel double-type balcony connections
PublikacjaThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
Modeling the application of steel slag in stabilizing expansive soil
PublikacjaThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Selected problems on application of steel sandwich panels to marine
PublikacjaW pracy przedstawiono wybrane problemy stosowania stalowych laserowo spawanych paneli w konstrukcji statku. Problemy te wynikają ze specyfiki cienkiej, spawanej laserowo konstrukcji stalowej i obejmują szerokie spektrum zagadnień począwszy od własności wytrzymałościowychy elementarnego połączenia teowego spawanego laserowo poprzez łączenie paneli ze sobą a skończywszy na integracji paneli z konstrukcją tradycyjną.
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublikacjaGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublikacjaThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Corrosion degradation impact on mechanical properties of structural steel
PublikacjaRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublikacjaThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublikacjaW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublikacjaThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Assesment of (Mn,Co)3O4powders for possible coating material for SOFC/SOEC interconnects
PublikacjaIn this work (Mn,Co)3O4 spinel powders with different Mn:Co ratio (1:1 and 1:2) and from different commercial suppliers are evaluated for possible powder for production of interconnect coatings. Sinterability of the powders is evaluated on pressed pellets sintered in oxidizing and in reducing/oxidizing atmospheres. For selected powder, coatings are then prepared by the electrophoretic deposition method on Crofer 22 APU stainless...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublikacjaUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
R and D: Research and Development Kobe Steel Engineering Reports
Czasopisma -
SEAISI Quarterly (South East Asia Iron and Steel Institute)
Czasopisma -
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Comparative analysis of different numerical models of a steel radial gate
PublikacjaHydrotechnical structures are important components in water management system and general flooding safety. Their reliability should be ensured since potential damage might lead to catastrophic consequences. Weir gates are considered to be highly vulnerable elements of each hydro power plant, with regard to its dynamic resistance. The aim of the paper is to compare different numerical models and their influence on the results of...
-
Temper bead welding of S460N steel in wet welding conditions
PublikacjaWet welding is the most common method of welding in water environment. It is most often used for repairing of underwater parts of offshore structures. However, the water as a welding environment causes an increase of susceptibility of steels to cold cracking. For underwater constructions high strength low alloy (HSLA) steel are widely used. In wet welding condition a HSLA steel is characterized by high susceptibility to cold cracking....
-
Evaluation of recycled tyre steel fibres adhesion to cement matrix
Publikacja -
The degradation mechanisms of a nanobainitic steel under cavitation erosion conditions
Publikacja -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publikacja -
Fatigue life tests of steel laser-welded sandwich structures
PublikacjaW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
Tests of local strains in steel laser - welded sandwich structure
PublikacjaW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
Efect of ageing on microstructure and impact properties of 9Cr-1Mo steel
PublikacjaBadano wpływ długotrwałego starzenia na mikrostrukturę i właściwości udarnościowe trzech przemysłowych wytopów stali typu 9Cr-1Mo. Wczesniejsze badania wykazały, że w stali 9Cr-1Mo starzonej w 550C przez 10 000 godzin występuje kruchość odpuszczania, a przy dłuższych czasach ekspozycji tworzy się krucha faza Lavesa (FeCr)2Mo na granicach ziaren. Powoduje to wzrost teperatury przejściowej kruchości oraz spadek energii łamania powyżej...
-
Thermal Fatigue Influence of Laser Treated Tool Steel Surface
Publikacja -
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publikacja -
Experimental research of the stability of steel cylindricalshell subjected to circumferential compression
PublikacjaAt the Department of Metal Structures Gdańsk University of Technology, experiments have been performed on the stability of shell of steel cylindrical models. The experiments have been carried on a test bench built at the Department. The design based on other test benches which were created in the past by other scientists, where modernized by the courtesy of companies that offer modern solutions. The test bench enables to generate...
-
The influence of plastic deformation on the magnetoelastic properties of the CSN12021 grade steel
PublikacjaWłasności magnetosprężyste materiałów są silnie modyfikowane przez zmiany struktury dyslokacyjnej, które są wynikiem procesów deformacji plastycznej. Zmiany te mogą być wykorzystane jako podstawa do opracowania metody nieniszczącej oceny stopnia deformacji materiału.Jak dotychczas zaproponowane zostały różne metody, oparte na pomiarach pętli histerezy magnetycznej czy też natężenia magnetycznego efektu Barkhausena. Artykuł porównuje...