Filtry
wszystkich: 6646
-
Katalog
- Publikacje 4908 wyników po odfiltrowaniu
- Czasopisma 51 wyników po odfiltrowaniu
- Konferencje 7 wyników po odfiltrowaniu
- Wydawnictwa 1 wyników po odfiltrowaniu
- Osoby 68 wyników po odfiltrowaniu
- Wynalazki 14 wyników po odfiltrowaniu
- Projekty 6 wyników po odfiltrowaniu
- Laboratoria 3 wyników po odfiltrowaniu
- Zespoły Badawcze 2 wyników po odfiltrowaniu
- Aparatura Badawcza 3 wyników po odfiltrowaniu
- Kursy Online 32 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 1550 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: temperature%20measurement
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublikacjaIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
EXHAUST TEMPERATURE MEASUREMENTS OF THE MARINE TURBOCHARGED DIESEL ENGINES IN OPERATION
PublikacjaThe article presents the selected metrology issues concerning the exhaust temperature of the turbocharged marine engines during operation. The special concern has been paid on existing disturbances as well as thermodynamical interpretation of the recorded measurement signal. A diagnostic informativeness of the standard exhaust temperature’s measurements has worked out while the engine runs in steady states has been also considered...
-
Local properties of organic coatings close to glass transition temperature
PublikacjaAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
The Influence of Abrasive Machine on Temperature During One Side Lapping
PublikacjaPrzedstawiono wyniki badań temperatury układu wykonawczego docierarki jednotarczowej. Analizowano temperaturę trzech pierścieni prowadzących separatory przy wykorzystaniu kamery termograficznej V-20 II firmy VIGO System S.A.
-
Coatings for improvement of high temperature corrosion resistance of porous alloys
PublikacjaPorowate stopy metaliczne są potencjalnymi podłożami nośnymi dla tlenkowych ogniw paliwo. Ich stosowanie obniża cenę ogniw paliwowych, co zaowocuje ich szybszą komercjalizacą. Jednak są one podatne na korozję w wysokich temperaturach. Dotychczas brak jest metod, które mogą poprawić rezystancję korozyjną porotawych stopów w wysokich temperaturach porowatych stopy do zastosowań SOFC. W tym artykule zaproponowano sposób na poprawę...
-
Changes in bacterial cells induced by high pressure at subzero temperature
PublikacjaW publikacji przedstawiono wyniki badań dotyczące zmian jakie zachodzą w komórkach bakterii Escherichia coli po działaniu wysokiego ciśnienia w ujemnej temperaturze. Stwierdzono, że w wyniku działania ciśnienia 193 MPa zachodzącą zmiany w błonie cytoplazmatycznej i ścianie komórkowej bakterii. W tych warunkach następowała prawie całkowita utrata wewnątrzkomórkowego ATP z komórek badanych szczepów znajdujących się w fazie logarytmicznej....
-
Proton Conducting Ceramic Powder Synthesis by a Low Temperature Method
PublikacjaMolten salt synthesis (MSS) is a simple method for the preparation of ceramic powders with specific morphology. The main role of the molten salts is to increase the reaction rate and lower the reaction temperature. It occurs because of much higher mobility of reactants in the liquid medium than in the solid state. In this work the molten salt synthesis was applied to produce ceramic powders of La0995Ca0005NbO4 and BaCe09−xZrxY01O3....
-
Electrochemical capacitor temperature fluctuations during charging/discharging processes
PublikacjaThepaperpresentsaproposalofusingadditionalstatisticalparameterssuchas:standarddeviation,variance, maximum and minimum increases of the observed value that were determined during measurements of temperature fields created on the surface of the tested electrochemical capacitor. The measurements were carriedoutusingthermographicmethodsinordertosupportassessmentoftheconditionofelectrochemical capacitorunderclassicdurabilitytestsbasedonmethodsofdeterminationofcapacityandequivalentseries...
-
Investigation of the temperature modulation parameters on semiconductor gas sensor response
PublikacjaIn this work we present the results of the investigation of the sensing properties of semiconductor gas sensors with a sinusoidally modulated temperature in the presence of synthetic air (SA) and three volatile air pollutants, i.e. NH3, NO2 and SO2. The measurements were performed for different average sensor heater temperatures and the amplitude of the modulation signal. In addition, the extraction of features from the sensor...
-
Wavelet Transform Analysis of Temperature Modulated Gas Sensor Response
PublikacjaThe aim of the study was to evaluate whether it is possible to extract the information about the gas concentration despite the influence of humidity. Commercial semiconductor sensor response was examined under the application of a periodic temperature change. The data was collected using measurement protocol for different concentrations of ammonia at specified levels of relative humidity. In this work we focused on the evaluation...
-
Photovoltaic module temperature stabilization with the use of phase change materials
PublikacjaThe worldwide growth of photovoltaics (PVs) has formed an exponential curve for more than four decades. During this period of time, PVs have evolved from a pure niche market of small-scale applications towards becoming a mainstream electricity source. The influence of temperature on the electrical parameters of crystalline silicon solar cells and solar modules is well described in the literature. In order to diminish these effects,...
-
Hyaluronan-Chondroitin Sulfate Anomalous Crosslinking Due to Temperature Changes
PublikacjaGlycosaminoglycans are a wide class of biopolymers showing great lubricating properties due to their structure and high affinity to water. Two of them, hyaluronic acid and chondroitin sulfate, play an important role in articular cartilage lubrication. In this work, we present results of the all-atom molecular dynamics simulations of both molecules placed in water-based solution. To mimic changes of the physiological conditions,...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Molecular Strategy for Survival at a Critical High Temperature in Eschierichia coli
PublikacjaThe molecular mechanism supporting survival at a critical high temperature (CHT) in Escherichia coli was investigated. Genome-wide screening with a single-gene knockout library provided a list of genes indispensable for growth at 47°C, called thermotolerant genes. Genes for which expression was affected by exposure to CHT were identified by DNA chip analysis. Unexpectedly, the former contents did not overlap with the latter except...
-
CaO-based high temperature CO2 sorbents – Literature review
PublikacjaThe use of CaO-based adsorbents has a high potential to capture CO2 from various systems due to its high reactivity with CO2, high capacity, and low cost of naturally derived CaO. The application of CaO-based sorbents to remove carbon dioxide is based on a reversible reaction between CaO and CO2. However, multiple carbonation/calcination cycles lead to a rapid reduction in the sorption capacity of natural CaO, and therefore efforts...
-
Performance of acicular grindable thermocouples for temperature measurements at sliding contacts
PublikacjaThe present study investigates the performance of acicular grindable thermocouples based on a constantan wire / steel hollow cylinder construction. The experiments showed that the measuring junction electrical resistance, temperature–voltage characteristic, measuring junction rise time and signal noise standard deviation of the acicular thermocouples are comparable to those of conventional J-type thermocouples with bare wire diameter...
-
On the differential effect of temperature on the Nusselt-Rayleigh relationship in free convection
PublikacjaThe aim of and inspiration behind this paper was to explain the reasons, also observed by other researchers, of the discrepancy in the results of experimental free convection, which for small Rayleigh and Nusselt numbers in the initial phase of research can sometimes reach several hundred percent. These discrepancies decrease with increasing heating power and plate surface temperature, in proportion to the increase in Ra and Nu,...
-
ZnO ALD-Coated Microsphere-Based Sensors for Temperature Measurements
PublikacjaIn this paper, the application of a microsphere-based fiber-optic sensor with a 200 nm zinc oxide (ZnO) coating, deposited by the Atomic Layer Deposition (ALD) method, for temperature measurements between 100 and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor head in real-time, which allows for higher accuracy during...
-
Multi-Channel Virtual Instrument for Measuring Temperature—A Case Study
PublikacjaThe article presents the hardware and software configuration of the developed multi-channel temperature measurement system as well as calibration procedures and measurement results verifying the properties of measurement channels. The system has been developed and dedicated primarily for measuring the temperature distribution in a laboratory model simulating underground power lines. With the adopted configuration of the analog...
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublikacjaBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Temperature influences on shear stability of a nanosize plate with piezoelectricity effect
PublikacjaPurpose The purpose of this paper is to predict the mechanical behavior of a piezoelectric nanoplate under shear stability by taking electric voltage into account in thermal environment. Design/methodology/approach Simplified first-order shear deformation theory has been used as a displacement field. Modified couple stress theory has been applied for considering small-size effects. An analytical solution has been taken into account...
-
Sum of Effective Temperatures in Colorado Beetle Control
Publikacja -
Wpływ temperatury na skład produktów pirolizy
PublikacjaPraca prezentuje wyniki badań pirolizy biomasy przy różnych temperaturach maksymalnych prowadzenia pro- cesu. Biomasą użytą w eksperymentach były zrębki brzozowe. Analizowano udziały masowe pięciu frakcji pro- duktów: karbonizatu, smół lekkich, smół ciężkich, wody oraz gazu pirolitycznego. Wykonano także analizy ciepła spalania poszczególnych frakcji w zależności od temperatury prowadzenia procesu. Eksperymenty wykonano przy pomocy...
-
Monitorowanie temperatury podczas gładzenia długich otworów
PublikacjaW rozdziale przedstawiono wyniki badań temperatury podczas gładzenia otworów w elementach stalowych. Badano otwory o średnicach 75H7, 75H10 i 150H7 mm. Do analiz zastosowano metodę termowizyjną. Otrzymane wyniki badań pozwolą uzyskać wysoką dokładność wymiarową otworów w częściach metalowych, a także właściwie zaplanować miejsce i czas kontroli końcowej.
-
Monitorowanie temperatury elementów wykonawczych docierarki jednotarczowej
PublikacjaW rozdziale przedstawiono badania monitorowania temperatury elementów układu kinematycznego docierarki jednotarczowej przy użyciu metody termowizyjnej. Badano temperaturę tarczy docierającej podczas jej wyrównywania, temperaturę pierścieni i rolek prowadzących, separatorów oraz przedmiotów obrabianych z miedzi i żeliwa. W badaniach stosowano różne wartości prędkości obrotowych tarcz docierających oraz ziarnistości ścierniw.
-
Pomiary temperatury podczas gładzenia długich otworów
PublikacjaW referacie przedstawiono wyniki badań temperatury podczas gładzenia długich otworów na obrabiarce poziomej ze sterowaniem CNC. W badaniach wykorzystano metodę termowizyjną. Analizowano wpływ rodzaju osełek oraz podstawowych parametrów technologicznych gładzenia na ubytek materiału obrabianego oraz przyrost temperatury na powierzchni przedmiotu.
-
Pomiary temperatury podczas gładzenia długich otworów
PublikacjaW artykule przedstawiono wyniki badań temperatury podczas gładzenia otworów w elementach stalowych. Badano otwory o średnicach 75H7 i 150H7 mm. Do analiz zastosowano metodę termowizyjną. Otrzymane wyniki badań pozwolą uzyskać wysoką dokładność wymiarową otworów w częściach metalowych, a także właściwie zaplanować miejsce i czas kontroli końcowej.
-
Reducing the Uncertainty of the Moving Object Location Measurement with the Method of Quasi-Multiple Measurement in GNSS Technology in Symmetrical Arrangement
Publikacja -
Reducing the Uncertainty of the Moving Object Location Measurement with the Method of Quasi-Multiple Measurement in GNSS Technology in Symmetrical Arrangement
PublikacjaThe article presents a solution to the problem of limited accuracy of dynamic measurements performed with GNSS receivers. The proposed measurement method is a response to the needs related to the assessment of the measurement uncertainty of the position of the track axis of the rail transport line. However, the problem of reducing the measurement uncertainty is universal for many different situations where high accuracy of positioning...
-
USE OF LANGMUIR PROBE IN DIESEL ENGINE DIAGNOSTIC RESEARCH Part I MEASUREMENT TECHNOLOGY. - Part 1 : MEASUREMENT TECHNOLOGY
PublikacjaIn the paper, the basic assumptions of diesel engine cylinder system's diagnosing method, based on observation of emerging and moving electric charges of ionized gas in the combustion workspaces, using Langmuir's probe. In the first part of the paper, only the technology of the measurement and results of the preliminary diagnostic tests of laboratory engine Farymann Diesel D10 were presented. The primary purpose of the research...
-
<title>Temperature sensor based on double-core optical fiber</title>
Publikacja -
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
High temperature corrosion of stainless steels for Solid Oxide Fuel Cells
PublikacjaW pracy przedstawiono wyniki korozyjności wysokotemperaturowej stali litych i porowatych stosowanych w tlenkowych ogniwach paliwowych.
-
Field investigation on seawater temperature variability in relation to horizontal optical gradient
Publikacja -
<title>White-light interferometric temperature sensor for biomedical diagnostic</title>
Publikacja -
Performance evaluation of temperature effect on hot in-place recycling asphalt mixtures
Publikacja -
Finding Temperature Distribution at Heat Recovery Unit Using Genetic Algorithms
Publikacja -
Normalized Method for Land Surface Temperature Monitoring on Coastal Reclaimed Areas
Publikacja -
Contribution of PsbS Function and Stomatal Conductance to Foliar Temperature in Higher Plants
Publikacja -
Regulation of replication of λ phage and λ plasmid DNAs at low temperature
Publikacja -
An Experimental Study on the Effect of Temperature on Acoustic Emission Characteristics in Metallic Structures
Publikacja -
The Influence of Magnetron Sputtering Process Temperature on ZnO Thin-Film Properties
Publikacja -
Verification of the exponential model of body temperature decrease after death in pigs
Publikacja -
Novel catalysts for low temperature synthesis of single wall carbon nanotubes
Publikacja -
Metal Oxides and Low Temperature SWCNT Synthesis via Laser Evaporation
Publikacja -
Temperature-dependent interactions in the chitosan/cyclosporine A system at liquid–air interface
Publikacja -
Numerical analysis of the influence of combustible material on the temperature field during fire
Publikacja -
Low-temperature air plasma modification of chitosan-coated PEEK biomaterials
Publikacja -
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publikacja