wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: automatic system, optical measurements, measurements of biological tissues
-
Electron diffision coefficients in triatomic gases measurements and model
PublikacjaPraca zawiera porównanie współczynników dyfuzji elektronów w gazach trójatomowych (N2O, C2O) zmierzonych w doświadczeniu ze współczynnikami wyznaczonymi numerycznie z wykorzystaniem równania Boltzmanna oraz z zastosowaniem metody Monte Carlo. Przedstawiona procedura pozwala zweryfikować przekroje czynne na zderzenia elektronów z drobinami gazów.
-
On accurracy of polarization resistance estimation by electrochemical noise measurements
PublikacjaPrzedstawiono sposób estymacji rezystancji polaryzacji, wykorzystywanej do oceny szybkości procesów korozji. Zaproponowano formułę określającą błąd losowy estymacji rezystancji polaryzacji. Przytoczono i przedyskutowano eksperymentalne wyniki estymacji rezystancji polaryzacji na podstawie pomiarów szumów elektrochemicznych w układzie trzech elektrod pomiarowych.
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublikacjaThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Measurements of the mechanical system properties of "SpeedLine magnetic" ultra-fast robot prototype for IML labeling
Dane BadawczeThe mechanical system tests of the high-speed IML labeling robot "SpeedLine Magnetic" were carried out in order to analyze the effects of the drive system's operating parameters on vibration and noise.
-
The results of the nitrogen adsorption/desorption measurements of CPMD and CPMH
Dane BadawczeThe results of the nitrogen adsorption/desorption measurements of CPMD and CPMH. The adsorption/desorption isothermswere carried out at 77 K using a Quantachrome Autosorb-1C-MS instrument. Sample abbreviations (CPMD, CPMH) are in agreement with the markings used in the linked publication.
-
Automatic system of constructions corrosion risk assessment
PublikacjaPrzedstawiony został system pomiaru szybkości korozji pracujący w przemysłowej instalacji wodnej. Mierzone wartości szybkości korozji przesyłane są za pomocą telefonii komórkowej (GPRS) co umożliwia obserwację wyników on-line. Zastosowanie tego rodzaju systemu pozwala na wykonywanie pomiarów korozyjnych umożliwiających kontrolę instalacji w sposób ciągły.
-
Internet-based automatic hearing assessment system
PublikacjaCelem referatu jest prezentacja systemu przesiewowego badania słuchu w oparciu o Internet. Wady słuchu stanowią jedną z najszybciej postępujących chorób we współczesnym społeczeństwie. W tym kontekście ważne staje się umożliwienie przeprowadzania masowych testów wykrywających ubytki słuchu. Przedstawiona aplikacja zawiera audiometryczny test tonalny, test ilustrowany dla dzieci oraz test rozumienia mowy w szumie. Po zakończeniu...
-
Results of electrical voltage measurements in reactors - part 1
Dane BadawczeResults of electric voltage measurements in six reactors using various plantings. These are the results of the project: Integrated approach 3M (Macrophytes-Microbiome-Modelling) to elucidate mechanisms of bioenergy production and micropollutants transformation in Floating Treatment Wetlands combined with Microbial Fuel Cells.
-
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublikacjaIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Stationary underwater channel experiment: Acoustic measurements and characteristics in the Bornholm area for model validations
PublikacjaThe underwater acoustical channel is time-variant, and even on small time scales there is often existing no ‘acoustical frozen ocean’. Popular is the use of WSSUS-channel transmission modeling (Wide-Sense Stationary Uncorrelated Scattering) for the stochastic description of bandpass signals in GSM mobile phones with moving participants; since this results in a halved number of model parameters. For underwater sound applications...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublikacjaThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Measurements of raising of 160EC pantograph type
Dane BadawczeIn this description the results of the experiment and also simulation performed on the total assembly of the 160 EC pantograph type is given. Multibody dynamics of pantograph rising due to external torque and forces are measured for parameter validation of the pantograph model.
-
XPS measurements of the iron elements covered by chromium
Dane BadawczeAnticorrosive coatings are an important issue in modern materials engineering. One of the most commonly used, for that coating materials, is chrome. Three metal elements were measured, named as Turcja, WB Tech and Nomet. Names were given according to producer of elements. XPS measurements of the Cr 2p region give an ansver concering on surface chemical...
-
GNSS INVENTORY OF HISTORIC NARROW-GAUGE RAILWAY LINE IN KOSZALIN UNDER EXTREMELY UNFAVORABLE MEASUREMENTS CONDITIONS FROM THE POINT OF VIEW OF SATELLITE SIGNALS AVAILABILITY
PublikacjaA team of academic researchers from the Gdańsk University of Technology, Gdynia Maritime University and the Polish Naval Academy have been working since 2009 on the methodology of using active GNSS geodetic networks for geodetic inventory of railways and on adapting this measurement technique for designing geometric layouts of railway and tram lines. Over the years, the team tested a variety of configurations of receivers and settings...
-
Measurements of no-load and short-circuit parameters of power transformers with taps
Dane Badawcze1) The Laboratory LINTE^2 is a large research infrastructure operated by the Faculty of Electrical and Control Engineering at Gdańsk University of Technology, to be found in Gdańsk, Poland (54.3690 N, 18.6130 E).
-
Performance measurements and optimization of visualization of routes traveled in the distributed dispatcher and teleinformation system for visualization of multimedia data for the Border Guard
PublikacjaMonitoring of country maritime border is an important task of the Border Guard. This activity can be enhanced with the use of the technology enabling gathering information from distributed sources, processing of that information and its visualization. The system presented in the paper is an advancement of the previously developed distributed map data exchange system. The added functionality allows to supplement the map data with...
-
Paweł Burdziakowski dr inż.
Osobydr inż. Paweł Burdziakowski jest specjalista w zakresie fotogrametrii i teledetekcji lotniczej niskiego pułapu, nawigacji morskiej i lotniczej. Jest również licencjonowanym instruktorem lotniczym oraz programistą. Głównymi obszarami zainteresowania jest fotogrametria cyfrowa, nawigacja platform bezzałogowych oraz systemy bezzałogowe, w tym lotnicze, nawodne, podwodne. Prowadzi badania w zakresie algorytmów i metod poprawiających...
-
Isolation of the relative decrease in magnetic permeability contribution to reluctance of an open magnetic circuit based on stray field measurements
PublikacjaThe goal of the study was to evaluate a relative decrease in magnetic permeability in open magnetic circuits based on stray magnetic field measurements. The boundary element method was used to simulate magnetic circuits with variable geometry and variable magnetic permeability. The simulated magnetic circuits were rectangular or bone-shaped flat samples. Reluctance was increased in the middle of the samples resulting in leakage...
-
Multiregional PI control strategy for dissolved oxygen and aeration system control at biological wastewater treatment plant
PublikacjaThe dissolved oxygen is a key parameter for biological processes at wastewater treatment plant. The dissolved oxygen tracking problem is one of the most complex and fundamental issue of biological processes. The paper proposes a new multiregional control strategy for dissolved oxygen tracking problem. The aeration system is included in overall control structure. The control mechanism within the operating point area is based on...
-
AeroSense Measurements: Wind Tunnel Ecole Centrale Lyon
Dane BadawczeData from wind tunnel tests of Aerosesne measurement system installed on NACA 63418 aerfoil in the anechoic wind tunnel at the Ecole Centrale Lyon.
-
The Concept of Accuracy Analysis of the Vertical Displacements Gained from the Hydrostatic Levelling Systems’ Measurements
PublikacjaAbstract: Nowadays, hydrostatic levelling is a widely used method for the vertical displacements’ determinations of objects such as bridges, viaducts, wharfs, tunnels, high buildings, historical buildings, special engineering objects (e.g., synchrotron), sports and entertainment halls. The measurements’ sensors implemented in the hydrostatic levelling systems (HLSs) consist of the reference sensor (RS) and sensors located on the...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublikacjaThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Correction of far-field measurements obtained in non-anechoic test site
Dane BadawczeThe dataset contains raw and processed measurements of radiation pattern characteristics performed in non-anechoic regime for two geometrically small antenna structures: a spline-parameterized Vivaldi structure and a compact spline-based monopole. The responses have been obtained at the selected frequencies of interest as a function of mentioned structures...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublikacjaPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Artur Gańcza dr inż.
OsobyI received the M.Sc. degree from the Gdańsk University of Technology (GUT), Gdańsk, Poland, in 2019. I am currently a Ph.D. student at GUT, with the Department of Automatic Control, Faculty of Electronics, Telecommunications and Informatics. My professional interests include speech recognition, system identification, adaptive signal processing and linear algebra.
-
DISPLACEMENT MEASUREMENTS DURING LOAD TESTING OF THE RAILWAY ARCH BRIDGE
Publikacja -
Optimization of impedance measurements using ‘chirp’ type perturbation signal
Publikacja -
The application of impedance measurements for the determination of the probability of the course of corrosion processes
Publikacja -
Corrosion rate measurements by non-linear electrochemical impedance spectroscopy
Publikacja -
Electromagnetic Field Measurements of Bow Thruster Drive with Frequency Converter
Publikacja -
Radiated emissions measurements of a portable power bank in a GTEM cell
Publikacja -
Use of a Virtual Instrument for Measurements of Direct Voltages in the Presence of Interferences
Publikacja -
Lattice dynamics of HgSe: Neutron scattering measurements andab initiostudies
Publikacja -
Thermal Transitions in P3HT:PC60BM Films Based on Electrical Resistance Measurements
Publikacja -
Correction of determined coordinates of railway tracks in mobile satellite measurements
Publikacja -
Measurements and numerical simulations of laser hardening and remelting thermal cycles
Publikacja -
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublikacjaArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Badania wykonano przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Analysis of Turbulent Flow Measurements in a Flume with Induced Upward Seepage
Publikacja -
Optimization of impedance measurements using ''chirp'' type perturbation signal
PublikacjaW pracy przedstawiono innowacyjny sposób pomiaru impedancji przy użyciu sygnału niestacjonarnego "chirp". W procesie akwizycji pobudzenia i odpowiedzi prądowej zastosowano zmienną częstotliwość próbkowania. Podejście takie pozwala zarówno na wielokrotne zmniejszenie ilości niezbędnych do otrzymania widma impedancyjnego rejestrowanych danych jak również upraszcza i przyspiesza proces obliczeniowy. Stwierdzono iż dokładność wyników...
-
Pitting corrosion characterization by electrochemical noise measurements on asymmetric electrodes
PublikacjaKorozja wżerowa stali nierdzewnych może być wykryta za pomocą obserwacji charakterystycznych sygnałów prądowych, jakie płyną między dwiema elektrodami metalowymi. W artykule proponuje się wyznaczanie funkcji bispektrum dla układu dwóch elektrod o istotnie różnej powierzchni narażonej na występowanie korozji. Proponowana metoda została zastosowana do analizy korozji wżerowej stali 0H18N9 powstającej pod wpływem 1M roztworu FeCl3...
-
Monitoring of CRT by means of impedance multiple measurements - simulation studies
PublikacjaCardiac resynchronization therapy (CRT) is a very promising treatment for patients with congestive heart failure. An Impedance Cardiography (ICG) is used for evaluation of heart mechanical activity. A simulation study with the use of a FEM model was performed. The developed realistic model of the thorax, based on CT data obtained from examination of a 68-year-old man, consisted of 212 000 tetrahedral elements. Different configurations...
-
Mechanism of Butanol Adsorption from Solution. 1. Calorimetric Measurements
Publikacja -
Absolute total cross-section measurements for electron collision with tetrahydrofuran
PublikacjaZmierzono absolutny, całkowity przekrój czynny na rozpraszanie elektronów na drobinach tetrahydrofuranu (C4H8O) w zakresie energii zderzenia 1-370 eV. Otrzymane wyniki pozostają w dobrej zgodności z sumą obliczonych przekrojów elestycznych i jonizacyjnych. Przeprowadzono porównananie z innymi dostępnymi przekrojami czynnymi.
-
A new OSS design based on parameter sensitivity tochanges in measurements
PublikacjaW wyniku istniejących silnych ograniczeń praktycznych i etycznych nałożonych na eksperymenty medyczne, procedura estymacji parametrów w diagnozie i terapii jest często zagadnieniem skomplikowanym. Jeśli dane pomiarowe pobierane są w postaci próbek krwi, liczba tych próbek, a także czas obserwacji powinny być zminimalizowane. Optymalizacja eksperymentu polega na optymalizacji odpowiedniego sformułowanego kryterium będącego funkcją...
-
Measurements of head surfaces of endoprostheses = Pomiary powierzchni głów endoprotez
PublikacjaW niniejszej pracy rozpatrywane są połowicze i całkowite endoprotezy. Rezultaty badań koncentrują się na wynikach pomiarów chropowatości powierzchni głów połowiczych i całkowitych endoprotez stawu biodrowego. Pomiary dokonane zostały dla połowiczych endoprotez z głową przyspawaną do trzpienia oraz endoprotez Frankobala z dwuczęściową głową osadzoną na sworzniu. Pomiary powierzchni dla próbek powierzchni głowy, całkowitej i połowiczej...
-
Measurements of Path Loss in Off-Body Channels in Indoor Environments
PublikacjaThe main goal of the paper is to investigate the influence of body orientation and on-body antenna placement on the path loss in off-body communications. In addition, the influence of different bodies is analysed.
-
Scattering of electrons by a 1,2-butadiene (C4H6) molecule: measurements and calculations
PublikacjaWe present the results of experimental and theoretical study on electron collisions with a 1,2-butadiene (H2C=C=CHCH3) molecule. Absolute grand-total cross sections (TCSs) were measured using a linear electron-transmission method for collision energies in the 0.5–300 eV range. Two distinct features in the TCS energy curve were detected: a narrow peak located at 2.3 eV and a broad enhancement centered around 9 eV. We attributed...
-
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublikacjaArtykuł dotyczy badań eksperymentalnych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. W badaniach zastosowano termografię ciekłokrystaliczną i cyfrową anemometrię obrazową.
-
On the power systems performance control starting from disturbances measurements
PublikacjaReferat przedstawia badanie działania układu sterowania w systemie elektroenergetycznym oparte na oszacowanie parametrów. Na podstawie pomiarów wykonanych w stanie zakłóconiowym, parametry te są oszacowane minimizując uchyb pomiędzy wartościami wielkości uzyskanych z pomiarów i wartościami wielkości wyjściowych modelu systemu elektroenergetycznego. W celu zmniejszenia tego uchybu, proponowano dwie metody: klasyczna oparta na czułości...