Wyszukiwarka
Wyniki wyszukiwania dla: AA2024 ALUMINUM ALLOY
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublikacjaThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Artificial neural network based fatigue life assessment of friction stir welding AA2024-T351 aluminum alloy and multi-objective optimization of welding parameters
PublikacjaIn this paper, the fracture behavior and fatigue crack growth rate of the 2024-T351 aluminum alloy has been investigated. At first, the 2024-T351 aluminum alloys have been welded using friction stir welding procedure and the fracture toughness and fatigue crack growth rate of the CT specimens have been studied experimentally based on ASTM standards. After that, in order to predict fatigue crack growth rate and fracture toughness,...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublikacjaThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
PA32 aluminum alloy - tensile properties
Dane BadawczeIn addition to steel, aluminium alloys are the main building material used in the shipbuilding industry. Due to its undoubted advantages, such as low density (nearly three times lower than in the case of steel for shipbuilding) and high corrosion resistance, it is often used for hulls of yachts and small vessels as well as superstructures. For safety...
-
Cutting forces and temperature measurements in cryogenic assisted turning of AA2024-T351 alloy: An experimentally validated simulation approach
Publikacja -
Local buckling of thin-walled channel member flange made of aluminum alloy
PublikacjaThe paper deals with local stability of the thin-walled compressed flange of channel columns and beams made of aluminum alloy. The aim of paper is to find critical stress of local buckling of the flange member taking into account the web-flange interaction in linear and nonlinear elastic range of the member material. The governing differential equation of the problem is derived with aid of the principle of stationary total potential...
-
Surface Characteristics of Plasma Treated and Titanium Nitride (TiN) Deposited Aluminum Alloy
Publikacja -
Local buckling of compressed flange of cold-formed channel members made of aluminum alloy
PublikacjaThe paper deals with local buckling of a compressed single flange of thin-walled channel cold- formed columns and beams made of aluminum alloy. Material is described by means of the Ramberg-Osgood constitutive equation. Axial compression of the columns and beams undergoing bending is taken into consid- eration. A simple model of the member flange in the form a long beam elastically connected to the web is used to find the critical...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublikacjaThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
The impact of laser surface treatment on the microstructure, wear resistance and hardness of the AlMg5 aluminum alloy
Publikacja -
Passive layer cracking studies performed on A95056 Aluminum Alloy by DEIS and acoustic emission
PublikacjaZbadano proces pękania warstwy pasywnej na stopie aluminium A95056 w warunkach zmiennych naprężeń rozciągających i polaryzacji anodowej z wykorzystaniem techniki DEIS oraz emisji akustycznej (AE), jako metody porównawczej. Określono elektrochemiczne i mechaniczne przyczyny badanego procesu. Wyznaczono progową (krytyczną) wartość naprężeń, przy których zarejestrowano proces pękania warstwy pasywnej na badanym stopie aluminium. Badanemu...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublikacjaThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublikacjaThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
Corrosion Inhibition Mechanism and Efficiency Differentiation of Dihydroxybenzene Isomers Towards Aluminum Alloy 5754 in Alkaline Media
PublikacjaThe selection of efficient corrosion inhibitors requires detailed knowledge regarding the interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. The position of functional groups between different isomers is often overlooked, but is no less important, since factors like steric hinderance may significantly affect the adsorption mechanism. In this study, we have presented how...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublikacjaThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
Fractographical quantitative analysis of EN-AW 2024 aluminum alloy after creep pre-strain and LCF loading
PublikacjaThis paper explores the applicability of a new damage parameter combining both fracture surface topography and loading features to estimate the fatigue lifetime under creep pre-strain and low-cycle fatigue loading. Fractures of EN-AW 2024 aluminum alloy caused by mixed creep and low-cycle fatigue loading are experimentally characterized and quantified via surface topography analysis. The specimens were preliminary damaged in a...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublikacjaThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Tribological Properties of Ni-P/Si3N4 Nanocomposite Layers Deposited by Chemical Reduction Method on Aluminum Alloy AW-7075
PublikacjaThe article presents the results of tribological tests of Ni-P/Si3N4 nanocomposite and Ni-P nickel layers deposited on the AW-7075 aluminum alloy by chemical reduction method, and the AW-7075 alloy without coating. Nanocomposite layers were produced using Si3N4 siliconnitride in the form of a polydisperse powder whose particle sizes ranged from 20 to 25 nm. The influence of the content of the dispersion phase layer material on...
-
Experimental investigations and damage growth modeling of EN‐AW 2024 aluminum alloy under LCF loading accounting creep pre‐deformation
PublikacjaThis article presents the results of experimental tests of creep rupture and of low-cycle fatigue (LCF) of EN-AW 2024 aluminum alloy devoid of damage and having preliminary damage. The preliminary damage was dealt in the process of creep at elevated temperature 100C, 200C, and 300C until achievement of two different strain values at each temperature. Samples with preliminary damage were subjected to fatigue tests at room temperature....
-
Dynamic Behavior of Aluminum Alloy Aw 5005 Undergoing Interfacial Friction and Specimen Configuration in Split Hopkinson Pressure Bar System at High Strain Rates and Temperatures
Publikacja -
Localized impedance measurements of AA2024 and AA2024-T3 performed by means of AFM in contact mode
PublikacjaPurpose: The purpose of this paper is to present the results of an atomic force microscopy (AFM) based approach to local impedance spectroscopy (LIS) measurement performed on AA2024 and AA2024-T3 aluminium alloys. Design/methodology/approach: AFM-LIS measurements were performed ex-situ without the electrolyte environment, so in fact the electrical not electrochemical impedance was obtained. Findings: Relative local impedance values...
-
Effect of native air-formed oxidation on the corrosion behavior of AA7075 aluminum alloys
PublikacjaThe microstructure of aluminum alloys plays a key role in their corrosion resistance. In particular, the presence of intermetallic precipitates differing in the potential from the alloy matrix induces local corrosion. The study presents the effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloy. Various microscopic and spectroscopic techniques were used to examine the changes occurring in the...
-
A comprehensive evaluation of mimosa extract as a corrosion inhibitor on AA6060 alloy in acid rain solution: part I. Electrochemical AC methods
PublikacjaThe inhibition effect of mimosa extract on the corrosion of AA6060 aluminum alloy in acid rain solution was investigated by electrochemical impedance spectroscopy and dynamic electrochemical impedance spectroscopy (DEIS). All the studied electrochemical parameters showed good corrosion inhibitive characteristics with respect to the aluminum alloy in the tested solution. Inhibitor efficiency increased with the concentration and...
-
Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions
PublikacjaInstantaneous impedance changes of 6060 and 6082 type aluminum alloys in pure water, and simulated acid rain poured into the pure water was investigated by dynamic electrochemical impedance spectroscopy (DEIS). In this way, the influence of aluminum content on the corrosion behavior of 6060 and 6082 type aluminum alloys immersed in simulated acid rain was determined. The corrosion rate of the alloy decreased with increasing Al...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
The microstructure of AA5754 alloy under corrosion in alkaline media (pH=11) with 20 mM of various carboxylic acids
Dane BadawczeThis dataset contains scanning electron microscopy (SEM) micrographs taken for polished aluminum AA5754 alloy samples, exposed for 100 min in bicarbonate buffer (pH=11) with the addition of 20 mM of carboxylic acids, namely: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, tricarballylic acid and serine. The goal of this study was...
-
The microstructure of AA5754 alloy under corrosion in alkaline media (pH=11) with 4.5 mM of various carboxylic acids
Dane BadawczeThis dataset contains scanning electron microscopy (SEM) micrographs taken for polished aluminum AA5754 alloy samples, exposed for 100 min in bicarbonate buffer (pH=11) with the addition of 4.5 mM of carboxylic acids, namely: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, tricarballylic acid and serine. The goal of this study was...
-
Acoustic emission studies of the 7075 aluminium alloy pitting corrosion process
Dane BadawczeThe dataset contains the cyclic polarization studies and corresponding acoustic emission measurements, revealing the pitting corrosion process of the passive layer at the surface of the 7075 aluminum alloy in the borate buffer with different chloride ions concentrations, in the range between 0.05 and 25 mM.
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublikacjaThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublikacjaIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublikacjaThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublikacjaComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublikacjaTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Kazimierz Darowicki prof. dr hab. inż.
OsobyStudia wyższe ukończyłem w czerwcu 1981 roku po zdaniu egzaminu dyplomowego i obronie pracy magisterskiej. Opiekunem pracy magisterskiej był dr hab. inż. Tadeusz Szauer. W roku 1991, 27 listopada uzyskałem stopień naukowy broniąc pracę doktorską zatytułowaną „Symulacyjna i korelacyjna analiza widm immitancyjnych inhibitowanej reakcji elektrodowej”. Promotorem pracy był prof. dr hab. inż. Józef Kubicki (Wydział Chemiczny...
-
The microstructure of aluminium alloys AA1050 and AA7075 subjected to anodic polarization at 8V in KOH electrolyte
Dane BadawczeThe dataset contains SEM pictures of the microstructure of aluminum alloy AA1050 and AA7075 exposed in aqueous KOH in the pH range between 14–11. Two sets of samples are presented, revealing the topography of the alloys when exposed to aggressive media under open circuit potential conditions as well as when subjected potentiodynamic polarization ranging...
-
SEM micrographs of aluminium corrosion in alkaline media with various bee products as corrosion inhibitors
Dane BadawczeThis dataset contains various scanning electron microscopy (SEM) micrographs of AA5754 aluminum alloy samples exposed to the corrosive alkaline environment without and with the addition of various bee products to act as green corrosion inhibitors. The products are bee pollen, honey, and putty. They were investigated in bicarbonate buffer (pH =10 or...
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublikacjaThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublikacjaThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
The effect of preliminary creep-strain on material behavior under LCF tension/compression and pure torsion regimes
PublikacjaThis paper presents the results of experimental tests of monotonic tension and torsion, creep-rupture and preliminary creep at 200C and 300C, as well as low-cycle fatigue of 2024 T3511 aluminum alloy. The fatigue process was conducted at room temperature for uniaxial tension/compression and torsion. The as-received material and pre-deformed material were also investigated during creep at elevated temperature. Basic monotonic,...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublikacjaThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublikacjaIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublikacjaThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel Friction Stir Welding Methods
PublikacjaThe present study investigates the effect of two parameters of process type and tool offset on tensile, microhardness, and microstructure properties of AA6061-T6 aluminum alloy joints. Three methods of Friction Stir Welding (FSW), Advancing Parallel-Friction Stir Welding (AP-FSW), and Retreating Parallel-Friction Stir Welding (RP-FSW) were used. In addition, four modes of 0.5, 1, 1.5, and 2 mm of tool offset were used in two welding...
-
Refining of Secondary Pb with Retention of Sn Using Al and Ca Additions
PublikacjaLead grid from spent lead-acid batteries contains significant amounts of tin and antimony. In classical pyro-refining processes of lead, tin oxidizes and is transferred to dross, making its recovery problematic and expensive. This paper presents an innovative method of pyro-refining lead using metallic aluminum and calcium to purify the lead from contaminants while retaining a higher amount of tin than in the traditional process....
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublikacjaThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
Low-Loss 3D-Printed Waveguide Filters Based on Deformed Dual-Mode Cavity Resonators
PublikacjaThis paper introduces a new type of waveguide filter with smooth profile, based on specially designed dual-mode (DM) cavity resonators. The DM cavity design is achieved by applying a shape deformation scheme. The coupling between the two orthogonal cavity modes is implemented by breaking the symmetry of the structure, thus eliminating the need for additional coupling elements. The modes operating in the cavity are carefully analyzed...
-
Localized impedance measurements of AA2024 and AA2024‐T3 performed by means of AFM in contact mode
Publikacja -
Jacek Tomków dr hab. inż.
OsobyWykształcenie:1. 2018 r.Doktor inżynier - Politechnika Gdańska, Wydział Mechaniczny, Inżynieria Materiałowa,rozprawa doktorska: Wpływ warunków spawania pod wodą na skłonność do tworzenia pęknięć zimnych w stalach o podwyższonej wytrzymałości 2. 2012 r.Magister inżynier - Politechnika Gdańska, Wydział Mechaniczny, Mechanika i Budowa Maszyn, specjalność: Technologia Maszyn i Komputerowe Wspomaganie Produkcji,praca magisterska: Badania...
-
Experimental and numerical analysis of an aluminum cantilevered beam with polymer adhesive
PublikacjaIn this paper, experimental and numerical investigation on a composite cantilevered aluminum beam has been conducted. The subject of the study consists of two plain aluminum elements bonded with polymer adhesive of different thickness. It has been proven in the previous study that this kind of material has high damping properties. During an experimental investigation, value of damping ratios have been obtained. The aim of a numerical...