Wyniki wyszukiwania dla: AMPHIBIOUS CRAFT, RESCUE, DESIGN, OPERATION
-
Low-cost 3D Printed Circularly Polarized Lens Antenna for 5.9 GHz V2X Applications
PublikacjaThis paper presents design and realization of a circularly polarized antenna consisting of a linearly polarized patch antenna and a 3D printed lens, at the same time performing the functions of wave collimator and a polarizer. The antenna is dedicated for 802.11p systems, as a part of road infrastructure, with operation bandwidth 5.85 - 5.925 GHz. Its realised gain and axial ratio at center frequency 5.9 GHz are 14.3 dBi and 2.17...
-
Softly Switched Robustly Feasible Model Predictive Control for Nonlinear Network Systems
PublikacjaIt is common that an efficient constrained plant operation under full range of disturbance inputs require meeting different sets of control objectives. This calls for application of model predictive controllers each of them being best fit into specific operating conditions. It further requires that not only designing robustly feasible model predictive controllers is needed to satisfy the real plant state/output constraints, but...
-
Compact satellite hydraulic unit
PublikacjaThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Prospects of ionic liquids application in electronic and bioelectronic nose instruments
PublikacjaThis paper addresses the problem of application of ionic liquids to chemical sensors and biosensors being an integral part of the electronic and bioelectronic-type instruments. The design and principle of operation of the electronic and bioelectronic noses are compared. Both the benefits and shortcomings of the application of ionic liquids in these type of instruments are described. The prospects of the development and application...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublikacjaIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
Local response surface approximations and variable-fidelity electromagnetic simulations for computationally efficient microwave design optimisation
PublikacjaIn this study, the authors propose a robust and computationally efficient algorithm for simulation-driven design optimisation of microwave structures. Our technique exploits variable-fidelity electromagnetic models of the structure under consideration. The low-fidelity model is optimised using its local response surface approximation surrogates. The high-fidelity model is refined by space mapping with polynomial interpolation of...
-
On Design Optimization of Miniaturized Microscrip Dual-Band Rat-Race Coupler with Enhanced Bandwidth
PublikacjaIn the paper, a novel topology of a miniaturized wideband dual-band rat-race coupler has been presented. Small size of the circuit has been obtained by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased in order to secure sufficient circuit flexibility in the context of its design optimization for dual-band operation. Optimum dimensions of...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
The impact of environmentally friendly refrigerants on heat pump efficiency
PublikacjaThis paper discusses the issue of heat pump simulation. Lower operating costs can be achieved through good equipment design and appropriate operation. Detailed technical and economic analysis inform the selection of system components with the highest possible efficiency and lower energy demand. The use of systems based on environmentally friendly refrigerants can deliver long product life, which is associated with a shorter payback...
-
Multi-objective design optimization of antennas for reflection, size, and gain variability using kriging surrogates and generalized domain segmentation
PublikacjaCost-efficient multi-objective design optimization of antennas is presented. The framework exploits auxiliary data-driven surrogates, a multi-objective evolutionary algorithm for initial Pareto front identification, response correction techniques for design refinement, as well as generalized domain segmentation. The purpose of this last mechanism is to reduce the volume of the design space region that needs to be sampled in order...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
A New Geodetic Method of Examination of Geometrical Conditions of a Crane Bridge
PublikacjaSafety is one of the key aspects related to crane-based material transport. In order to ensure safe crane operation and material transport, it is necessary to meet certain geometrical conditions. The authors addressed the geometrical conditions of a crane bridge, a substantial crane component. The paper presents the method to compute displacement components of points on the top of a bridge crane relative to their design position....
-
Novel Family of Single-Phase Modified Impedance-Source Buck-Boost Multilevel Inverters With Reduced Switch Count
Publikacjahis paper describes novel single-phase solutions with increased inverter voltage levels derived by means of a nonstandard inverter configuration and impedance source networks. Operation principles based on special modulation techniques are presented. Detailed component design guidelines along with simulation and experimental verification are also provided. Possible application fields are discussed, as well as advantages and disadvantages....
-
Miniaturized uniplanar triple-band slot dipole antenna with folded radiator
PublikacjaA miniaturized uniplanar slot dipole for triple-frequency operation is presented. The antenna consists of a folded slot radiator with an increased number of degrees of freedom that allow for efficient size reduction. Rigorous electromagnetic (EM)-driven design optimization is applied in order to achieve the smallest possible size while maintaining acceptable levels of antenna reflection at the required operating frequencies. The...
-
Rapid design closure of microwave components by means of feature-based optimization and adjoint sensitivities
PublikacjaIn this article, fast design closure of microwave components using feature-based optimization (FBO) and adjoint sensitivities is discussed. FBO is one of the most recent optimization techniques that exploits a particular structure of the system response to “flatten” the functional landscape handled during the optimization process, which leads to reducing its computational complexity. When combined with gradient-based search involving...
-
NEW DESIGNS OF CENTRIFUGAL MAGNETIC FLUID SEALS FOR ROTATING SHAFTS IN MARINE TECHNOLOGY
PublikacjaThe centrifugal magnetic fluid seals have important advantage over the conventional centrifugal seals. They maintain very good sealing capacity at static, medium and high speeds of shaft rotation, with the increased seal lifetime, and minimum torque and static friction. These seals are particularly useful in cases when the angular shaft velocity varies and sometimes decreases to nearly or exactly zero, such as in flywheel applications,...
-
Current risk analysis and management issues in technical systems.
PublikacjaDealing with the reliability and safety of industrial hazardous plants requires taking into account relevant interdisciplinary scientific knowledge and some existing approaches based on so-called good engineering practice, also those included in the international standards and guidelines. In this article an approach is proposed how to integrate the functional safety concept with information security aspects in the design and management...
-
A structure and design optimization of novel compact microscrip dual-band rat-race coupler with enhanced bandwidth
PublikacjaIn the letter, a topology of a novel compact wideband dual-band rat-race coupler has been presented along with its computationally efficient design optimization procedure. Reduction of the circuit size has been achieved by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased so as to secure sufficient flexibility of the circuit, necessary in...
-
Multi-Fidelity Local Surrogate Model for Computationally Efficient Microwave Component Design Optimization
PublikacjaIn order to minimize the number of evaluations of high-fidelity (“fine”) model in the optimization process, to increase the optimization speed, and to improve optimal solution accuracy, a robust and computational-efficient multi-fidelity local surrogate-model optimization method is proposed. Based on the principle of response surface approximation, the proposed method exploits the multi-fidelity coarse models and polynomial interpolation...
-
Innovative method for utilization of wastewater for security and safety in rural areas
PublikacjaIn the rural areas building of sewerage systems and central wastewater treatment plants (WWTPs) often brings too high costs, due to high distances from one farm to another and terrain configuration. Individual treatment systems for each farm are a good solution. The teratment wetlands for nine individual farms were constructed in Kaszubian Lake District in summer and autumn 2009. Three configurations of reed beds were chosen. In...
-
Redesign of the Research Platform for Monitoring, Control and Security of Critical Infrastructure Systems
PublikacjaCritical Infrastructure Systems (CISs) play a key role in modern societies. Their sustainable operation depends heavily on the performance of dedicated structures and algorithms targeting monitoring, control and security aspects. In previous work a Research Platform (RP) for the design and simulation of such systems was presented. This works updates the information on the RP through the description of major hardware and software...
-
Designing control strategies of aeration system in biological WWTP
PublikacjaThe paper presents the complete design processes of a novel aeration control systems in the SBR (Sequencing Batch Reactor) wastewater treatment plant (WWTP). Due to large energy expense and high influence on biological processes, the aeration system plays a key role in WWTP operation. The paper considers the aeration system for a biological WWTP located in the northeast of Poland. This system consists of blowers, the main collector...
-
Low-Loss Mechanically Tunable Resonator and Phase Shifters in Groove Gap Waveguide Technology
PublikacjaThis research is focused on the design and realization of high-performance high-power variable phase shifters in groove gap waveguide technology. Specifically, it is shown that the unique characteristic of groove gap waveguides, which is its proper operation without the need for electrical connection between the top and bottom sections of the waveguide, can be used to design mechanically tunable devices. Using the proposed method,...
-
Identification of ship’s hull mathematical model with numerical methods
PublikacjaThe modern maritime industry is moving toward the development of technology that will allow for full or partial autonomy of ship operation. This innovation places high demands on ship performance prediction techniques at the design stage. The researchwork presented in the article is related to the design stage of the ship and concerns methods for prognosis and evaluation of the specific operational condition of the ship, namely...
-
Analytical design method of reverse curves
PublikacjaThe paper deals with a new approach relating to the design of the region of railway track direction alteration adapted to Mobile Satellite Measurements technique. The method may be particularly useful in situations when both the straights of the route directions cannot be connected in an elementary way using a circular arc with transition curves; this also refers to the application of a compound curve. Thus the only solution becomes...
-
Numerical analysis of chip removing system operation in circular sawing machine using CFD software
PublikacjaPaper presents the analysis of the results of numerical simulations of the air flow process of wood chips removing system in the circular sawing machine. The attention is focused on the upper cover and bottom shelter of the chip removing system. Within the framework of the work a systematic numerical modeling of the air flow distribution in the cover and shelter during operation of the selected rotational speed of saw blade with...
-
Wpływ ekologicznych czynników roboczych na efektywność układu sprężarkowej pompy ciepła (The impact of environmentally friendly refrigerants on heat pump efficiency)
PublikacjaArtykuł poświęcony jest zagadnieniu symulacji pracy układu sprężarkowej pompy ciepła. Prawidłowe zaprojektowanie instalacji oraz jej właściwe użytkowanie pozwala na zmniejszenie kosztów eksploatacji. Dokładna analiza techniczno-ekonomiczna umożliwia natomiast dobór elementów systemu o możliwie największej sprawności, a zatem niskim zapotrzebowaniu na energię. Zastosowanie układów opartych o perspektywiczne, proekologiczne czynniki...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Assessment of performance of unmanned maritime vehicles (USV, UUV, AUV) by CFD and MES investigation, PG_00053662
Kursy OnlineThe course entitled "Assessment of Performance of Unmanned Maritime Vehicles" consists of the following problems to be discussed during the lectures (W): - major areas of application of UMV unmanned maritime vehicles, - sea environment, - types of UMV vehicles, - parameters, characteristics and features of UMV vehicles, - research, design, construction, implementation and operation of UMV vehicles, - systems of UMV vehicles...
-
The analytical design method of railway route’s main directions intersection area
PublikacjaThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Integrated safety and security analysis of hazardous plants and systems of critical infrastructure
PublikacjaThis article addresses an integrated safety and security analysis approach of hazardous industrial plants and systems of critical infrastructure. Nowadays due to new hazards that emerge there are opinions among experts that these issues require an integrated approach in life cycle, from the design concept, through the design and operation of the plant, to its decommissioning. It is proposed to start from an interesting methodology...
-
Designing issues of the alarm system in context of functional safety and human factors
PublikacjaThis article addresses selected aspects of the alarm system and human factors that should be evaluated during the design and operation of an industrial hazardous installation. In such installations the layer of protection analysis (LOPA) methodology is often applied for simplified risk analysis based on defined accident scenarios. To reduce and control the risks the safety instrumented functions (SIFs) are identified and their...
-
Sewage gardens - constructed wetlands for single family households
PublikacjaDuring the last 30 years the increase of interest in low-cost decentralized and small wastewater treatment plants (WWTP) is observed in Europe. For this purpose sand filters, stabilization ponds, mini reactors with activated sludge, trickling filters and treatment wetlands are used. Among the listed facilities treatment wetlands (TWs) offer effective and reliable treatment efficiency, being at the same time low-cost and simple...
-
Pareto Ranking Bisection Algorithm for Expedited Multi-Objective Optimization of Antenna Structures
PublikacjaThe purpose of this letter is introduction of a novel methodology for expedited multi-objective design of antenna structures. The key component of the presented approach is fast identification of the initial representation of the Pareto front (i.e., a set of design representing the best possible trade-offs between conflicting objectives) using a Pareto-ranking bisection algorithm. The algorithm finds a discrete set of Pareto-optimal...
-
Hybrid use of the building as a method supporting epidemic safety
PublikacjaThe COVID-19 pandemic has resulted in changing organisational and technical requirements in the operation of treatment facilities. This paper summarises the available knowledge on the principles of hybrid design of the architecture of treatment units to ensure that different levels of sanitary and hygienic safeguards can be implemented. The basis of this narrative overview is an analysis of the existing Polish legislation on required...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Expedited optimization of antenna input characteristics with adaptive Broyden updates
PublikacjaSimulation-driven adjustment of geometry and/or material parameters is a necessary step in the design of contemporary antenna structures. Due to their topological complexity, other means, such as supervised parameter sweeping, does not usually lead to satisfactory results. On the other hand, rigorous numerical optimization is computationally expensive due to a high cost of underlying full-wave electromagnetic (EM) analyses, otherwise...
-
Fast Design Closure of Compact Microwave Components by Means of Feature-Based Metamodels
PublikacjaPrecise tuning of geometry parameters is an important consideration in the design of modern microwave passive components. It is mandatory due to limitations of theoretical design methods unable to quantify certain phenomena that are important for the operation and performance of the devices (e.g., strong cross-coupling effects in miniaturized layouts). Consequently, the initial designs obtained using analytical or equivalent network...
-
Fault-tolerant performance of the novel five-phase doubly-fed induction generator
PublikacjaThe article presents the concept of a new design of a multi-phase doubly-fed induction generator (DFIG). The innovative design approach uses a five-phase power supply from the rotor side of the generator with a three-phase classic stator power supply. Modern three-phase doubly-fed induction generators are the dominant choice for Wind Energy Conversion Systems (WECS). Solutions of this type are sensitive to the loss of at least...
-
A High-Efficient Low-Voltage Rectifier for CMOS Technology
PublikacjaA new configuration of rectifier suiting CMOS technology is presented. The rectifier consists of only two nchannel MOS transistors, two capacitors and two resistors; for this reason it is very favourable in manufacturing in CMOS technology. With these features the rectifier is easy to design and cheap in production. Despite its simplicity, the rectifier has relatively good characteristics, the voltage and power efficiency, and...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
FEA analysis of the multicell piezoelectric motor
PublikacjaThe presented paper concerns a design, modeling and chosen tests of the prototype multicell piezoelectric motor (MPM). The principle of operation based on three independent traveling wave actuators is presented. The main materials and technologies used in the fabrication process are described. The structure of the motor is modeled using static and modal FEM analysis. The process of traveling wave generation in the MPM structure...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublikacjaThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
Nonlinear secondary arc model use for evaluation of single pole auto-reclosing effectiveness
PublikacjaPurpose – The purpose of this paper is to discuss two evaluation methods of single pole autoreclosing process effectiveness in HV transmission lines. Secondary arc current and recovery voltage results obtained by load flow calculation are compared to the results obtained by the time domain simulations. Moreover, a nonlinear secondary arc implementation is presented. Design/methodology/approach – A computer simulation studies were...
-
Vehicle dynamics
Kursy Online(W) Vehicle dynamics (W-Lecture) - DAPE - WIMiO The course entitled "Vehicle dynamcs" (VD) is conducted for the DAPE WIMiO Students. The VD course is to discuss the following problems: - major problems of vehicle dynamics from the application point of view, - definition of working environment, - types of vehicles, - parameters and characteristics of vehicles, - assessment of performance of vehicles towards design, - vehicle...
-
Technical monitoring system for a new part of Gdańsk Deepwater Container Terminal
PublikacjaDevelopment strategy for the port of Gdańsk assumes that , up to 2027, it will become the main transport centre in the Baltic Sea region. To this end , for many years work has been carried out to facilitate access to the port both by sea and land. One of the elements of extension of the port is the building of another terminal of Deepwater Container Terminal , Gdańsk. In this task, geotechnical operations aimed at appropriate...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublikacjaIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
SiC-based T-type modules for multi-pulse inverter with coupled inductors
PublikacjaThe paper presents SiC-based three-level T-type modules designed for a high-performance 30kVA DC/AC inverter operating at high frequency 85 kHz with low THD of the output voltage. This inverter system consists of two integrated parts. The first part is active and contains three parallelconnected three-phase T-type modules built with fast-switching SiC power transistors. The second, passive part of the system is a set of inductors...
-
Rectangular Waveguide Filters Based on Deformed Dual-Mode Cavity Resonators
PublikacjaIn this paper, a novel design for rectangular waveguide filters with deformed dual-mode (DM) cavity resonators is demonstrated. The new resonant cavity shape is a result of applying shape deformation to the basic rectangular cavity to enable its dual-mode operation. Internal coupling between the two orthogonal cavity modes is realized by geometry deformation, eliminating the need for additional coupling elements. The designs are...
-
A Wideband Corrugated Ridged Horn Antenna with Enhanced Gain and Stable Phase Center for X- and Ku-Band Applications
PublikacjaIn this letter, a structure and design procedure of a novel double-flared conical horn antenna with an improved gain and a stable phase center is presented. The antenna incorporates a hybrid ridged and corrugated structure. A double-ridged section is responsible for ensuring a wideband operation, whereas the corrugated section supports the hybrid mode. The antenna impedance bandwidth (VSWR < 2) is 6 GHz to 20 GHz. Excellent performance...