Wyszukiwarka
Filtry
wszystkich: 322
Wyniki wyszukiwania dla: FRICTION MATERIAL
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublikacjaThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublikacjaAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
PublikacjaThis study investigated the influence of the amount of steel and copper fibres in a train brake friction material on the tribological performance, emission intensity and characteristics of airborne wear particles. The particles were generated on a pin-on-disc tribometer under controlled friction and environmental conditions. It was found that the steel fibre results in a more intensive emission of 0.3–10 μm particles compared to...
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublikacjaThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublikacjaThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublikacjaThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublikacjaFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Friction Resistances in Internal Gear Pump with Modified Sickle Made of Plastic
PublikacjaThis paper presents modifications of the sickle insert (constructional and material) made in a gear pump with internal meshing. The introduced design change consists in making an incision in the sickle insert. Due to this treatment, the races of the insert are pressed against the apex wheels of the gears. The introduced compensation causes a smaller drop in pump efficiency with increasing discharge pressure. The article describes...
-
MECHANICAL PROPERTIES OF BOTTOM ASH – DREDGED MATERIAL MIXTURES IN LABORATORY TESTS
PublikacjaBottom ash from EC Gdańsk and dredged material taken from the mouth of The Vistula were mixed to form an engineering material used for dike construction. Mixtures with different bottom ash content were tested in laboratory to determine its basic physical and mechanical properties. The optimum bottom ash–dredged material mixture, built in the corps of the test dike, contains 70% of ash. The optimum bottom ash content in the mixture...
-
A Study on Emission of Airborne Wear Particles from Car Brake Friction Pairs
PublikacjaThe emission of airborne wear particles from friction material / cast iron pairs used in car brakes was investigated, paying special attention to the influence of temperature. Five low-metallic materials and one non-asbestos organic material were tested using a pin-on-disc machine. The machine was placed in a sealed chamber to allow airborne particle collection. The concentration and size distribution of 0.0056 to 10 μm particles...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublikacjaThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Reliability model of the crankshaft-piston assembly
PublikacjaThe laws that govern the durability of crankshaft-piston assembly friction nodes can be proved or at least derived or justified in an intuitive way. Operation of all the friction nodes is disturbed by external factors occurring with randomly changing intensity and also appearing at random. As the crankshaft-piston assembly friction nodes have a series structure and effects of those disturbances accumulate, their fitness for use...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublikacjaThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Contact with coupled adhesion and friction: Computational framework, applications, and new insights
PublikacjaContact involving soft materials often combines dry adhesion, sliding friction, and large deformations. At the local level, these three aspects are rarely captured simultaneously, but included in the theoretical models by Mergel et al., (2019). We here develop a corresponding finite element framework that captures 3D finite-strain contact of two deformable bodies. This framework is suitable to investigate sliding friction even...
-
Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel Friction Stir Welding Methods
PublikacjaThe present study investigates the effect of two parameters of process type and tool offset on tensile, microhardness, and microstructure properties of AA6061-T6 aluminum alloy joints. Three methods of Friction Stir Welding (FSW), Advancing Parallel-Friction Stir Welding (AP-FSW), and Retreating Parallel-Friction Stir Welding (RP-FSW) were used. In addition, four modes of 0.5, 1, 1.5, and 2 mm of tool offset were used in two welding...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublikacjaThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublikacjaThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublikacjaThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublikacjaIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints–Overview
PublikacjaThe modern and eco-friendly friction stir welding (FSW) method allows the combination of even such materials that are considered to be non-weldable. The development of FSW technology in recent years has allowed a rapid increase in the understanding of the mechanism of this process and made it possible to perform the first welding trials of modern polymeric and composite materials, the joining of which was previously a challenge....
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublikacjaDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublikacjaBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublikacjaThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
Portico Farmhouses of the Vistula Delta: Architecture, Current State and Finite Element Modelling of Timber Roof Truss under Material and Cross-section Uncertainty
PublikacjaThe article focuses on the oldest surviving I-type portico houses located in the Vistula Delta, which were built in the 17th and 18th centuries. The study describes the houses’ origins, structure, details of roof structures and technical condition, and it also includes numerical modelling of a roof truss and its mechanical analysis. Numerical models of the roof trusses are defined and analysed by means of the finite element method....
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublikacjaAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...