Filtry
wszystkich: 133
wybranych: 124
Wyniki wyszukiwania dla: STRENGTHENING BURNISHING
-
Problems of Flaking in Strengthening Shaft Burnishing
PublikacjaThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
Roller burnishing
PublikacjaThe paper shows the process of roller burnishing as a method of finishing machine components. Based on own research the author presents the effects of the roller burnishing process to increase the hardness and residual stress as well as the wear and fatigue strength of burnishing components.
-
Smoothing of wood surface by burnishing
PublikacjaW artykule zaprezentowano rozwój bezwiórowych metod obróbki wykańczającej drewna. Przedstawiono wpływ nagniatania ślizgowego na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach wykonanych z drzewa sosnowego toczonych i nagniatanych ślizgowo. Nagniatanie ślizgowe przeprowadzono z wykorzystaniem nagniataka elastycznego o elemencie ślizgowym wykonanym z Karbonado. Wyniki odniesiono do głównych parametrów nagniatania...
-
Strengthening of structures by shock transmission units.
PublikacjaCelem niniejszego artykułu jest analiza możliwości zastosowania tzw. przenośników drgań do wzmacniania konstrukcji budowlanych (w tym mostowych) narażonych na oddziaływania dynamiczne takie jak: wiatr, siły hamowania pojazdów czy trzęsienia ziemi.
-
Mechanical Properties of Aluminium Bracket Strengthening
PublikacjaThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
Analysis of Historic Brick Walls' Strengthening Methods
PublikacjaAnalysis of the behavior of historical brick walls is difficult and complicated. However, computer calculations are being increasingly used in the evaluation of cultural heritage buildings and some of their elements. The aim of this paper is to analyze the historic brick walls reinforcement. Different methods of strengthening are compared and discussed. Numerical analysis, based on finite element method, was conducted on the assumption...
-
Numerical and Analytical Investigation of Aluminium Bracket Strengthening
PublikacjaThis paper focuses on an analytical and numerical investigation of aluminium brackets used to fasten light-weight curtain walls to building facilities. The authors propose a solution to increase the load capacity of aluminium brackets by means of additional cover plates (straps). This paper also includes a short survey of literature and material properties concerning the EN AW-6060 T6 aluminium alloy. This paper suggests an initiation...
-
Formation of wood surface roughness in burnishing process
PublikacjaW publikacji przedstawiono i omówiono rozwój bezwiórowych metod obróbki wykańczającej drewna przez nagniatanie. Przedstawiono wpływ nagniatania na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach toczonych i nagniatanych. Wyniki odniesiono do głównych parametrów nagniatania jak: siła nagniatania oraz promień zaokrąglenia elementu nagniatającego.
-
Sliding burnishing technology of holes in hardened steel
PublikacjaNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Surface vaviness of components machined by burnishing method
PublikacjaPowierzchnię po obróbce wykończeniowej definiuje się zazwyczaj za pomocą parametrów chropowatości. Rosnące wymagania jakościowe w stosunku do wytwarzanych części maszyn powodują rozszerzanie się zakresu parametrów opisujących powierzchnię. W artykule przedstawiono ocenę jakościową powierzchni nagniatanych za pomocą parametrów falistości.
-
Hybrid Processing by Turning and Burnishing of Machine Components
PublikacjaThe paper presents a method of hybrid manufacturing process of long 5 shafts and deep holes by simultaneous turning and burnishing method. The tech- 6 nological results of the research focus on the influence of the basic technological 7 parameters of this process on the surface roughness of piston rods of hydraulic 8 cylinders. Research results are presented in the graphs as well as mathematical 9 formula. Set of samples were made...
-
GPR investigation of the strengthening system of a historic masonry tower
PublikacjaIn this paper the condition assessment of the strengthening system of a masonry tower was carried out by the GPR method. The study provided unique experimental data acquired during measurements of the reinforced concrete frame embedded in masonry walls. Conducted numerical and experimental investigations were focused on the phenomenon of the diffraction-refraction scattering of the electromagnetic energy. A hyperbola resulting...
-
Strengthening the local communities’ competence for engaging in participatory planning
PublikacjaThe article describes the genesis of undertaking the subject of improving the planning competencies in local communities, in order to eliminate communication gaps to strengthen the civil attitudes. It puts forward a thesis that innovation in this issue involves creation of new participatory planning techniques, i.e. the described urban mentoring model. Describing the inclinations for undertaking the subject of the “Quo Vadis Gdansk?...
-
Application of ceramic and composite tools in smoothing burnishing process.
PublikacjaArtykuł zawiera oryginalne konstrukcje narzędzi nagniatających. Elementy nagniatające zostały wykonane z ceramiki i kompozytu ''Karbonado''. Narzędzia te mogą być stosowane na obrabiarkach CNC i centrach obróbkowych, zwłaszcza do obróbki stali hartowanych. Artykuł przedstawia również wyniki badań i przykłady zastosowań tych narzędzi w przemyśle.
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublikacjaThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
The surface contact characteristics after sliding and rolling burnishing.
PublikacjaW pracy przedstawiono zastosowanie nowej metody SCGC i odpowiedniego programu komputerowego JKC do oceny pomierzonej mikrostereometrii powierzchni części maszyn, głównie na potrzeby kontroli jakości. Na przykładzie powierzchni nagniatanych wykazano cechy nowej metody: wizualizację ułatwiającą wyobrażenie pomierzonej sfery chropowatości, położenie w niej najważniejszych parametrów oceny (rozkład geometrycznej powierzchni kontaktu,...
-
New ceramic and composite tools for smoothing burnishing process
PublikacjaW pracy przedstawiono nowe konstrukcje narzędzi ceramicznych i z kompozytu karbonado do nagniatania twardych hartowanych stali. Zamieszczono wyniki badań wpływu parametrów technologicznych nagniatania walcowych próbek ze stali 45 o różnej twardości 23-56HRC na chropowatość powierzchni próbek.
-
Development and importance of burnishing technology in computer integrated manufacturing
PublikacjaPrzedstawiono podstawy odkształcania nierówności powierzchni w wyniku różnych odmian procesu nagniatania. Opisano oryginalne technologie nagniatania i narzędzia dla następujących sposobów nagniatania: krążkowanie z dociskiem sztywnym i elastycznym, toczenie z jednoczesnym nagniataniem powierzchni zewnętrznych walcowych, nagniatanie elektromechaniczne, ślizgowe narzędziem diamentowym i oscylacyjne. Podano zalecane parametry obróbki...
-
Strengthening of thin-walled columns against flexuralbuckling at elevated temperatur.
PublikacjaZa pomocą analizy wrażliwości wyznaczono mmiejsca wzmocnienia słupa stalowego obciążonego działaniem wysokiej temperatury. Wyznaczono przybliżoną wartość siły krytycznej słupa przy zmiennej temperaturze. Zastosowano model stali zgodny z polską normą PN-90/B-03200.
-
The method of strengthening the church building in terms of the planned mining exploitation
Publikacja -
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublikacjaTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublikacjaDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
LOW PLACTICITY BURNISHING PROCESSES. Fundaments, tools and machine tools
PublikacjaW obszernej monografii (530 stron) autor przedstawił w sposób kompleksowy zagadnienia związane z wykończeniową metodą obróbki części maszyn przez powierzchniową obróbkę plastyczną-nagniataniem. Jest to pierwsza książka w języku angielskim poświęcona tej bezwiórowej i ekologicznej metodzie obróbki. W wielu przypadkach w technologii różnorodnych części maszyn i innych urządzeń, nagniatanie może zastąpić operację szlifowania. Ma to...
-
Technological and tribological aspects of milling-burnishing process of complex surfaces
Publikacja -
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublikacjaNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
COMPARATIVE NUMERICAL ANALYSIS OF DIFFERENT STRENGTHENING SYSTEMS OF HISTORICAL BRICK ARCHES
PublikacjaThe article presents a comparative numerical analysis of various ways to strengthen historical brick arches. Five ways of strengthening brick arches with steel tie-rods have been proposed. Two of these involve the use of braces wrapped around pillars supporting the arch connected with a tie-rod; another two ways involve the use of the tie-rods with welded metal sheets of different sizes; the last way involves the use of the tie-rod...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublikacjaHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublikacjaStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublikacjaA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Effects of rapid heating on non-equilibrium microstructure evolution and strengthening mechanisms of titanium alloy
Publikacja -
EVALUATION OF SURFACE ROUGHNESS PARAMETERS OF TURNED GEAR WHEELS HOLES MACHINED BY BALL BURNISHING
PublikacjaW artykule zaprezentowano wyniki z badań eksperymentalnych dotyczących przygotowania powierzchni do obróbki wykończeniowej nagniataniem. Badania dotyczyły obróbki materiałów w stanie utwardzonym po hartowaniu. analizowano wpływ parametrów toczenia na twardo na uzyskiwane wartości parametrów chropowatości powierzchni jako wejściowych przed procesem nagniatania.
-
Matrix Strengthening the Identification of Observations with Split Functional Models in the Squared Msplit(q) Estimation Process
PublikacjaThis article addresses the issue of raising the level of identification of observations with either single or more split functional models in the squared Msplit(q) estimation process. The theoretical part of the study presents the theoretical grounds for the classical method for estimating parameters in a split functional model and proposes a modification of the computational algorithm to increase the quality of the determinations...
-
Matrix Strengthening the Identification of Observations with Split Functional Models in the Squared Msplit(q) Estimation Process
Publikacja -
On the Microstructure, Microhardnessand Wear Behavior of Gray Cast Iron Surface Layer after Laser Strengthening
Publikacja -
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublikacjaThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Strengthening mechanism and precipitate evolution of a multi-application special engineering steel designed based on a hybrid idea
Publikacja -
Elective surgery system strengthening: development, measurement, and validation of the surgical preparedness index across 1632 hospitals in 119 countries
Publikacja -
Joining of tubular elements by internal rolling with use of burnishing tools.Łączenie elementów rurowych przez wewnętrzne rozpęczanie z użyciem nagniataków.
PublikacjaW referacie przedstawiono wyniki prac zmierzających do zastosowania nagniataków do łączenia rur aluminiowych przez ich rozgniatanie. Zaprezentowano analityczny szacunek wytrzymałości złącz i porównano z wynikami prób ich rozłączania na maszynie wytrzymałościowej.
-
Synergistic effect of nanoscale carbon black and ammonium polyphosphate on improving thermal stability and flame retardancy of polypropylene: A reactive network for strengthening carbon layer
Publikacja -
Solid-State Modification of Poly(butylene terephthalate) with a Bio-Based Fatty Acid Dimer Diol Furnishing Copolyesters with Unique Morphologies
PublikacjaCopolyesters based on poly(butylene terephthalate) (PBT) and a bio-based fatty acid dimer diol (FADD) were prepared by solid-state modification (SSM). The chemical incorporation of the FADD into the backbone of the PBT was proven using various techniques. It was clear that the incorporation rate was diffusion-limited rather than reaction-limited. From quantitative 13C NMR a nonrandom chemical microstructure was obtained at all...
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublikacjaPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Wpływ nagniatania ślizgowego na chropowatość zewnętrznych powierzchni obrotowych w częściach maszyn
PublikacjaPodano wyniki badań technologicznych nagniatania ślizgowego wałków ze stali C45.Obróbkę przeprowadzono na tokarce CNC z użyciem nagniataka z tensometrycznym pomiarem siły docisku.Zamieszczono wytyczne dla doboru parametrów obróbki według kryterium wymaganej chropowatości powierzchni obrobianej.
-
A HISTORICAL BUILDING'S RESTORATION IN THE CONSTRUCTIONAL ASPECT ON THE EXAMPLE OF A BUILDING LOCATED IN POLAND
PublikacjaObjects of cultural heritage are an extremely important element in the proper functioning of the social life. They provide information on our ancestors' actions, as well as shape our culture and social awareness. It is important for the historical objects to provide those information accurately, that is without any unnecessary human intervention over the years of the monument's existence. However, it is not always possible due...
-
Methods of deep modification of low-bearing soil for the foundation of new and spare air runways
PublikacjaAfter analyzing the impact of aircraft on the airport pavement (parking spaces, runways, startways), it was considered advisable to consider the problem of deep improvement or strengthening of its subsoil. This is especially true for low-bearing soil. The paper presents a quick and effective method of strengthening the subsoil intended for the construction of engineering structures used for civil...
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublikacjaIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
Improvement of the load capacity of the road overpass as a result of repairs after breakage caused by vehicle impacts
PublikacjaDamage of spans of the overpass caused by impact of underpassing vehicles are a frequent case. Objects that use prefabricated load-bearing elements that are not designed for such impacts are particularly exposed. After impact, such parts suffer extensive damage that need repair. Taking advantages of this recovery actions it is worth to perform strengthening that will protect object against possible future impacts. In this study...
-
Cyclic Behavior of Masonry Shear Walls Retrofitted with Engineered Cementitious Composite and Pseudoelastic Shape Memory Alloy
PublikacjaThe behavior of masonry shear walls reinforced with pseudoelastic Ni–Ti shape memory alloy (SMA) strips and engineered cementitious composite (ECC) sheets is the main focus of this paper. The walls were subjected to quasi-static cyclic in-plane loads and evaluated by using Abaqus. Eight cases of strengthening of masonry walls were investigated. Three masonry walls were strengthened with different thicknesses of ECC sheets using...