Filtry
wszystkich: 684
wybranych: 564
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: ŁOPATKI TURBINOWE
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublikacjaThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Startegie podmiotów rynku masowych towarów rolnych zawierających transakcje terminowe na giełach towarowych
PublikacjaW opracowaniu przedstawiono strategie podmiotów rynku masowych towarów rolnych zdecydowanych zawierać transakcje terminowe.
-
Two dimensional inverse method of turbomachinery stage design
PublikacjaW artykule przedstawion rys historyczny dotyczący modelu osiowo-symetrycznego w zastosowaniu do maszyn wirnikowych. Została sformułowana metoda rozwiązywania zadania odwrotnego polegaająca na znajdywaniu powierzchni będfącej obrazem łopatki w osiowo symetrycznym modelu maszyny wirnikowej. Zaprezentowano przykłady zastosowania tej metody w odniesieniu do łopatki kierowniczej turbiny, spreżarki promieniowej oraz pompo-turbiny.
-
Steam turbine as the main ship propulsion. More than a hundred years at sea.
PublikacjaPrzedstawiono rys historyczny rozwoju okrętowych turbin parowych. Omówiono główne rozwiązania konstrukcyjne podstawowych elementów parowych siłowni turbinowych i współczesne tendencje i perspektywy rozwoju tego napędu.
-
Influence of the steam within seals and glands of the turbine on its rotor motion stability.
PublikacjaPrzedstawiono metodę obliczania charakterystyk dynamicznych wpływu parowych uszczelnień turbin na ich dynamikę i stateczność ruchu wirników. Zarysowano model ''masowy'' uszczelnienia. Podano przykłady zastosowań.
-
Optimization of an axial turbine for a small scale ORC waste heat recovery system
Publikacja -
Identification of inertia, damping and stiffness parameters for low pressure steam turbine framework.
PublikacjaW pracy przedstawiono metodę identyfikacji masy tłumienia i sztywności kadłuba części niskoprężnej turbiny parowej 200MW.
-
Aerodynamic excitations generated in turbine shroud clearance determined bymeans of neural networks
PublikacjaSiły aerodynamiczne generowane w uszczelnieniach turbinowych z reguły opisywane są modelem liniowym. Przy dużych drganiach wirnika sposób ten daje niezbyt dokładne wyniki. Zaproponowano wykorzystanie sieci neuronowych do określania sił ciśnieniowych powstających w uszczelnieniu. Wyniki porównano z badaniami eksperymentalnymi.
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublikacjaThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Application of spatial neural simulators of turbine blade rows to fluid flow diagnostics
PublikacjaThis chapter presents the results of neural modelling of fluid flow in steam turbine row. In modelling working conditions of the flow channel varied, thus the aim of the work was to reconstruct the reference state - distributions of velocity, pressure, and losses in flow channel - with high accuracy for fluid flow diagnostics.
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublikacjaPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublikacjaThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublikacjaThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublikacjaThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Experimental Validation of Numerical Model within a Flow Configuration of the Model Kaplan Turbine
PublikacjaThis paper investigates validation of flow within a model Kaplan turbine. This includes comparison of various turbulence models and their influence on torque and power generated by the turbine. Numerical results were compared with experimental data.
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublikacjaIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Low speed permanent magnet synchronous generator for vertical axis wind turbine
PublikacjaThe paper presents design process and tests of a prototype low speed permanent magnet synchronous generator (PMSG) dedicated for the innovative vertical-axis wind turbine. The rated data of the designed generator are following: power - 15 kVA, voltage - 400 V (Y), rotation speed - 93.75 rpm. The design assumptions, chosen results of the design process and experimental tests of the prototype PMSG are presented. The considered PMSG...
-
The QDMC Model Predictive Controller for the Nuclear Power Plant Steam Turbine Control
PublikacjaThere are typically two main control loops with PI con trollers operating at each turbo-generator set. In this paper a model predictive controller QDMC for the steam turbine is proposed - instead of a typical PI controller. The QDMC controller utilize a step-response model for the controlled system. This model parameters are determined, based on the simplified and linear model of turbo-generator set, which parameters are identified...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublikacjaThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
Assessment of damage causes of a 17 m long wind turbine blade model
PublikacjaThe subject matter is to verify the stiffness of the steel supporting structure and assess the causes of cracks in the 17 m long wind turbine blade model
-
Nuclear Power Plant Steam Turbine - Modeling for Model Based Control Purposes
PublikacjaThe nature of the processes taking place in a nuclear power plant (NPP) steam turbine is the reason why their modeling is very difficult, especially when the model is intended to be used for on-line optimal model based process control over a wide range of operating conditions, caused by changing electrical power demand e.g. when combined heat and power mode of work is utilized. The paper presents three nonlinear models of NPP steam...
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublikacjaThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublikacjaThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublikacjaThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Numbers, Please: Power- and Voltage-Related Indices in Control of a Turbine-Generator Set
PublikacjaThis paper discusses the proper selection and interpretation of aggregated control performance indices values mirroring the quality of electrical energy generation by a turbine-generator set cooperating with a power system. Typically, a set of basic/classical and individual indices is used in energy engineering to ensure the mirroring feature and is related to voltage, frequency and active or reactive power deviations from their...
-
Recovering Sound Produced by Wind Turbine Structures Employing Video Motion Magnification
PublikacjaThe recordings were made with a fast video camera and with a microphone. Using fast cameras allowed for observation of the micro vibrations of the object structure. Motion-magnified video recordings of wind turbines on a wind farm were made for the purpose of building a damage prediction system. An idea was to use video to recover sound & vibrations in order to obtain a contactless diagnostic method for wind turbines. The recovered signals...
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublikacjaThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
Diagnosing wind turbine condition employing a neural network to the analysis of vibroacoustic signals
PublikacjaIt is important from the economic point of view to detect damage early in the wind turbines before failures occur. For this purpose, a monitoring device was built that analyzes both acoustic signals acquired from the built-in non-contact acoustic intensity probe, as well as from the accelerometers, mounted on the internal devices in the nacelle. The signals collected in this way are used for long-term training of the autoencoder...
-
Real-time hybrid model of a wind turbine with doubly fed induction generator
PublikacjaIn recent years renewable sources have been dominating power system. The share of wind power in energy production increases year by year, which meets the need to protect the environment. Possibility of conducting, not only computer simulation, but also laboratory studies of wind turbine operation and impact on the power system and other power devices in laboratory conditions would be very useful. This article presents a method...
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy.
PublikacjaW referacie przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonane zostały w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podstawie określono...
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy
PublikacjaW artykule przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonano w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podsatwie określono zmianę sprawności...
-
ZASTOSOWANIE METOD SZTUCZNYCH SIECI NEURONOWYCH DO PROJEKTOWANIA WIEŃCÓW ŁOPATKOWYCH W STOPNIACH TURBINOWYCH
PublikacjaPalisady łopatek turbinowych (zarówno kierownicze, jak i turbinowe) dla potrzeb badań i analiz projektowych charakteryzuje się poprzez wybrane zestawy parametrów geometrycznych i przepływowych. Przykłady takiego podejścia do opisu palisady kierowniczej i wirnikowej przedstawiono w tym rozdziale. Dane dla tych zakresów posłużyły do zbudowania bazy danych charakterystyk geometrycznych i związanych z nimi charakterystyk przepływowych...
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publikacja -
Some problems of self-excited vibrations of turbine rotors. Part I: The theoretical method
PublikacjaPrzedstawiono teoretyczną metodę określania uszczelnienia nadbandażowego lub dławicy zupełnej, które odgrywa największą rolę w generowaniu samowzbudnych drgań typu aerodynamicznego wirników turbinowych. Drgania harmoniczne układu wirnika turbiny opisane są macierzowym równaniem, a wymuszenia aerodynamiczne określane metodą współczynników wpływu.
-
Research into flows in turbine blade seals. Part III: Numerical calculations versus experiment
PublikacjaPrzedstawiono wyniki badań doświadczalnych przepływów w uszczelnieniu nadbandażowym stopnia turbinowego, przeprowadzonych na powietrznej turbinie modelowej. Rezultaty te porównano z wynikami badań numerycznych z zastosowaniem programu Fluent.
-
Wind resource assessment and energy yield prediction for the small wind turbine on the Szubieniczne Hill
PublikacjaThe goal of this study is to preliminary assess the wind resources on the Szubieniczne Hill in order to predict the annual energy production for planned small wind turbine. The analyzed site is located close to the Gdańsk University of Technology campus, in complex urban environment additionally surrendered by forested hills. The assessment is based on Computational Fluid Dynamics simulations which allow to evaluate the wind energy potential...
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublikacjaThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
Spectral Finite Element Method for Propagation of Elastic Waves in Wind Turbine Blades for SHM
PublikacjaW pracy przedstawiono model łopaty turbiny wiatrowej zbudowany z wykorzystaniem spektralnych elementów skończonych. Omówiono wyniki symulacji propagacji fal sprężystych i ich interakcji z uszkodzeniami w formie pęknięcia i delaminacji.
-
Changing the Ship Propulsion System Performances Induced by Variation in Reaction Degree of Turbocharger Turbine
PublikacjaArtykuł przedstawia szczegółowy model matematyczny układu napędu statku obejmującego: wolnoobrotowy silnik spalinowy okrętowy, śruba okrętowa oraz regulator prędkości kątowej. Model ten, następnie jest wykorzystany do badania symulacyjnego zachowania układu zarówno w stanach ustalonych jak i nieustalonych. Model jest zweryfikowany z wynikami eksperymentalnymi. Przedstawienie oryginalnej metody oceny wrażliwości układu względem...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublikacjaOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublikacjaCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublikacjaThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...