Filtry
wszystkich: 2416
wybranych: 1453
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL PILES
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publikacja -
Corrosion degradation impact on mechanical properties of structural steel
PublikacjaRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublikacjaThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Heat tint colours on stainless steel and welded joints
PublikacjaSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Selected problems on application of steel sandwich panels to marine
PublikacjaW pracy przedstawiono wybrane problemy stosowania stalowych laserowo spawanych paneli w konstrukcji statku. Problemy te wynikają ze specyfiki cienkiej, spawanej laserowo konstrukcji stalowej i obejmują szerokie spektrum zagadnień począwszy od własności wytrzymałościowychy elementarnego połączenia teowego spawanego laserowo poprzez łączenie paneli ze sobą a skończywszy na integracji paneli z konstrukcją tradycyjną.
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Fatigue properties of laser welded steel sandwich panel.
PublikacjaPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
Modification of cement-ash composites with steel fibre addition
PublikacjaPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Experimental tests of steel double-type balcony connections
PublikacjaThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublikacjaGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Modeling the application of steel slag in stabilizing expansive soil
PublikacjaThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublikacjaW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
Inline Waveguide Filter With Compact Frequency-Dependent Coupling Producing Two Additional Poles and Three Transmission Zeros
PublikacjaThis work reports a compact frequency-dependent coupling (FDC) structure introduced in a rectangular waveguide, which allows to generate two additional in-band transmission poles and three transmission zeros (TZs). This serves to increase the order/selectivity of the waveguide bandpass filter in a compact inline topology, thus without the need for any additional space/volume or cross coupling. The proposed FDC consists of a partial-height...
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublikacjaIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublikacjaUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublikacjaThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Experimental and numerical studies of double corrugated steel arch panels
Publikacja -
Estimation of the parameters of the discrete model of a steel–concrete composite beam
Publikacja -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publikacja -
Search for optimum geometry of selected steel sandwich panel joints
PublikacjaZastosowanie stalowych paneli typu sandwich w konstrukcjach okrętowych wymaga rozwiązania wielu problemów. Jednymi z trudniejszych zagadnień związanych z tymi nowymi strukturami są połączenia pomiędzy panelami oraz między panelami i konstrukcją innego typu. Artykuł przedstawia poszukiwanie optymalnej geometrii połączenia typu panel-panel w układzie wzdłużnym, przy użyciu parametrycznego modelu w programie ANSYS. Poszukiwano konfiguracji...
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublikacjaNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Fatigue life tests of steel laser-welded sandwich structures
PublikacjaW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
Tests of local strains in steel laser - welded sandwich structure
PublikacjaW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
Efect of ageing on microstructure and impact properties of 9Cr-1Mo steel
PublikacjaBadano wpływ długotrwałego starzenia na mikrostrukturę i właściwości udarnościowe trzech przemysłowych wytopów stali typu 9Cr-1Mo. Wczesniejsze badania wykazały, że w stali 9Cr-1Mo starzonej w 550C przez 10 000 godzin występuje kruchość odpuszczania, a przy dłuższych czasach ekspozycji tworzy się krucha faza Lavesa (FeCr)2Mo na granicach ziaren. Powoduje to wzrost teperatury przejściowej kruchości oraz spadek energii łamania powyżej...
-
Mechanical properties and corrosion resistance of dissimilar stainless steel welds
PublikacjaW artykule przedstawiono właściwości mechaniczne oraz odporność korozyjną doczołowych złączy różnoimiennych stali odpornych na korozję, austenitycznej 316L oraz duplex 2205. Blachy o grubości 15 mm spawano automatycznie łukiem krytyn z różnymi energiami liniowymi. Wykazano, że właściwości mechaniczne złączy spełniają wymagania okrętowych towarzystw klasyfikacyjnych, natomiast najbardziej narażoną strefą złącza na działanie korozji...
-
Experimental research of the stability of steel cylindricalshell subjected to circumferential compression
PublikacjaAt the Department of Metal Structures Gdańsk University of Technology, experiments have been performed on the stability of shell of steel cylindrical models. The experiments have been carried on a test bench built at the Department. The design based on other test benches which were created in the past by other scientists, where modernized by the courtesy of companies that offer modern solutions. The test bench enables to generate...
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publikacja -
Thermal Fatigue Influence of Laser Treated Tool Steel Surface
Publikacja -
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublikacjaConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Underwater wet welding of S1300 ultra-high strength steel
PublikacjaMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Numerical modal analysis of a vertical rising steel water gate
PublikacjaVertical rising steel water gates are very common not only in Poland and Germany but also in other countries of the world. Their popularity is mainly attributed to their simplicity of construction, which makes their production process cheaper and faster when compared to other solutions. The aim of this paper is to conduct a numerical modal analysis to examine the eigenvalues and eigenmodes of a vertical rising steel gate. Two cases...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublikacjaThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublikacjaThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
THE INTERACTION BETWEEN STEEL COLUMN CHORD AND CLOSELY SPACED REINFORCEMENT.
PublikacjaNowadays, more often than before, civil engineering designers are willing to use steel build-up members composed of single or doubled cold-formed chords interconnected using different mechanical connectors. This paper subject is an analysis of cooperation of a closely spaced built-up cold-formed chord interconnected with series of bolts that are located along the length of the member in a specific spacing. This distance along the...
-
Framework for Structural Health Monitoring of Steel Bridges by Computer Vision
PublikacjaThe monitoring of a structural condition of steel bridges is an important issue. Good condition of infrastructure facilities ensures the safety and economic well-being of society. At the same time, due to the continuous development, rising wealth of the society and socio-economic integration of countries, the number of infrastructural objects is growing. Therefore, there is a need to introduce an easy-to-use and relatively low-cost...
-
The degradation mechanisms of a nanobainitic steel under cavitation erosion conditions
Publikacja -
Evaluation of recycled tyre steel fibres adhesion to cement matrix
Publikacja -
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublikacjaUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
Surface treatment of C80U steel by long CO2 laser pulses
PublikacjaThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublikacjaEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Poli-optimization of selected variants of steel sandwich panels connections
PublikacjaPanele kompozytowe odgrywają coraz większą role w różnorodnych zastosowaniach inżynierskich. Jednym z zagadnień kluczowych dla możliwości aplikacyjnych są połączenia między cienkościennymi formami w układzie wzdłużnym i poprzecznym. Praca prezentuje wyniki polioptymalizacji numerycznej wybranych połączeń stalowych paneli typu sandwich.