Filtry
wszystkich: 977
Wyniki wyszukiwania dla: CONTROLLABLE BEARINGS
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublikacjaWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
Application of the Optimization Methods to the Search of Marine Propulsion Shafting Global Equilibrium in Running Condition
PublikacjaFull film hydrodynamic lubrication of marine propulsion shafting journal bearings in running condition is discussed. Considerable computational difficulties in non-linear determining the quasi-static equilibrium of the shafting are highlighted. The approach using two optimization methods (the particle swarm method and the interior point method) in combination with the specially developed relaxation technique is proposed to overcome...
-
STUDY IN MECHANICAL FAULT ELEMENT THERMOGRAPHY THROUGH THE MACHINE: The case of deep groove ball bearings of a career without screen.
Publikacja -
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublikacjaHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Stability and bearing capacity of arch-shaped corrugated shell elements: experimental and numerical study
Publikacja -
Correction to Aromatic Dendrimers Bearing 2,4,6-Triphenyl-1,3,5-triazine Cores and Their Photocatalytic Performance
Publikacja -
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublikacjaResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublikacjaBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Methods of deep modification of low-bearing soil for the foundation of new and spare air runways
PublikacjaAfter analyzing the impact of aircraft on the airport pavement (parking spaces, runways, startways), it was considered advisable to consider the problem of deep improvement or strengthening of its subsoil. This is especially true for low-bearing soil. The paper presents a quick and effective method of strengthening the subsoil intended for the construction of engineering structures used for civil...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublikacjaIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
STABILITY AND LOAD BEARING CAPACITY OF A BARS WITH BUILT UP CROSS SECTION AND ELASTIC SUPPORTS
PublikacjaThe present paper is devoted to the numerical analysis and experimental tests of compressed bars with built–up cross section which are commonly used as a top chord of the roof trusses. The significant impact on carrying capacity for that kind of elements in case of out-of-plane buckling is appropriate choice of battens which are used to provide interaction between separate members. Linear buckling analysis results and nonlinear static...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Bearing Capacity of aluminum bars with built-up cross section and glued or welded connections
PublikacjaThe paper is focused on numerical analysis and experimental test of aluminum bars with glued and welded connections between separate members. The connection properties were tested experimentally. The numerical analysis were conducted for the beam and shell model of the structure. The shape and magnitude of initial geometric imperfection was taken into account
-
IN VITRO PROPAGATION OF RHODODENDRON TOMENTOSUM - AN ENDANGERED ESSENTIAL OIL BEARING PLANT FROM PEATLAND
PublikacjaRhododendron tomentosum Harmaja (formerly Ledum palustre L.) is a medicinal peat bog plant native to northern Europe, Asia and North America. This plant has a distinctive aroma thanks to the presence of essential oil, to which it also owes its anti-inflammatory, analgesic, antimicrobial and insecticidal properties. However, in Europe R. tomentosum is classified as an endangered species, mainly due to degradation of peatlands. In...
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublikacjaThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublikacjaOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
Current-based higher-order spectral covariance as a bearing diagnostic feature for induction motors
PublikacjaConducting the diagnosis of induction motors remotely by analyzing the supply current is an attractive prospect with the lack of access to the engine. Currently, there is no solution, based on analysis of the current, the credibility of which would allow its use in industry. The statistics of bearing failures in induction motors indicate that they constitute more than 40% of induction motor damage, therefore, bearing diagnosis...
-
Investigation of Noise Threats and Their Impact on Hearing in Selected Schools
PublikacjaNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
Multimedia services applied to noise and hearing monitoring and measuring
PublikacjaThe goal of this chapter is to show a research study related to processing of data acquired by the multimedia services engineered at the multimedia systems department (MSD) of the Gdansk University of Technology. This concerns a survey on noise threat employing the multimedia noise monitoring system (MNMS) and hearing tests performed by the "I can hear. . . " system. The obtained results of the noise measurements revealed that...
-
Computer simulations of hearing aid acoustical system performance
Publikacja -
Audiovisual speech recognition for training hearing impaired patients
PublikacjaPraca przedstawia system rozpoznawania izolowanych głosek mowy wykorzystujący dane wizualne i akustyczne. Modele Active Shape Models zostały wykorzystane do wyznaczania parametrów wizualnych na podstawie analizy kształtu i ruchu ust w nagraniach wideo. Parametry akustyczne bazują na współczynnikach melcepstralnych. Sieć neuronowa została użyta do rozpoznawania wymawianych głosek na podstawie wektora cech zawierającego oba typy...
-
Fitting the mobile device characteristics to the user's hearing preferences
PublikacjaA method for fitting the mobile computer audio characteristics to the user's hearing preferences is proposed. The process consists of two stages: calibration and dynamics processing. During the calibration phase the user performs a loudness scaling test giving their response regarding the perceived loudness. The dynamics processing made on above basis sets the loudness to the most comfortable level. The processing accounts both...
-
Virtual hearing aid - the computer application for education purposes.
PublikacjaZrealizowano aplikację komputerową demonstrującą zasady działania aparatów słuchowych. Osoba z dobrym słuchem ma możliwość zapoznania się z problemem niedosłuchu i działaniem aparatu. Aplikacja wyposażona jest w intuicyjny interfejs, który przedstawia elementy aparatu słuchowego na schemacie blokowym z opcjami dotyczącymi źródła dźwięku, typu szumu oraz ustawień aparatu. Aplikacja wzbogacona jest o materiały dydaktyczne, opisujące...
-
Application of hybrid signals processors to speech and hearing aids
PublikacjaDzięki postępowi w technice Cyfrowych Procesorów Sygnałowych (ang. DSP) stało się możliwe budowanie miniaturowych protez słuchu i mowy. Mimo niewielkich wymiarów procesory te są w stanie wykonywać złożone algorytmy. Ich dodatkową zaletą jest łatwość zmiany oprogramowania, a co za tym idzie łatwość zmiany dziedziny zastosowań. W pracy skupiono się na zagadnieniach związanych z projektowanie i implementacją algorytmów mających zastosowanie...
-
Application of Intelligent Conversational Agents in E-learing Environments
PublikacjaThe paper concerns intelligent tutoring systems and concentrates on apliaction of virtual mentors in distance learning environments. Different educational agent types are described. The prototype of an agent developed at Gdansk University of Technology is also presented, as well as its internal representation and construction. Benefits of virtual mentors applied in distance learning are also pointed out.
-
A study on signal processing methods applied to hearing aids
PublikacjaThis paper presents a short survey on current technology available in hearing aids with a focus on digital signal processing techniques used. First, factors influencing the hearing aid effectiveness are introduced. Then, examples of the present DSP methods and strategies are provided. Also, a description of current limitations of hearing aids and future trends of development are shown. Finally, the notion of computational auditory...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Model and laboratory simulation of a induction motor for diagnostic purposes
PublikacjaStatistics say that bearings are this part of induction motors which is most susceptible to damage. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. A faulty bearing results in additional motor vibrations. They are reflected in the harmonic content of stator currents. In certain operating conditions the current signal is the sole source of information...
-
Journal of Essential Oil Bearing Plants
Czasopisma -
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublikacjaA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
EXPERIMENTAL STUDY OF DIFFERENT SUPPLY DESIGNS IN HYDRODYNAMIC THRUST BEARINGS = Badania doświadczalne różnych sposobów smarowania wzdłużnych łożysk ślizgowych
PublikacjaHydrodynamiczne łożyska wzdłużne charakteryzują się znacznymi stratami tarcia, które przyczyniają się do wzrostu temperatury łożyska i obniżenia jego nośności. Obecnie olej smarujący jest zazwyczaj chłodzony w zewnętrznych układach chłodzenia. Po schłodzeniu olej jest dostarczany z powrotem do korpusu łożyska, z reguły do przestrzeni między klockami łożyska. Skuteczność dostarczania schłodzonego oleju w pobliże wlotu do szczeliny...
-
First tests of water lubricated propeller shaft bearings = Wstępne badania zespołu smarowanych wodą łożysk okrętowego wału śrubowego
PublikacjaW pierwszej części referatu zaprezentowano nowe stanowsko badawcze przy pomocy którego można badać smarowane wodą łożyska wału śrubowego. W drugiej części pracy przedstawiono uzyskane wyniki pomiarów oporów ruchu i trajektorii osi wału.
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine
Publikacja -
Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data
Publikacja -
The influence of strain on the Verwey transition as a function of dopant concentration: towards a geobarometer for magnetite-bearing rocks
Publikacja -
Vibration-Based Diagnostics of Radial Clearances and Bolts Loosening in the Bearing Supports of the Heavy-Duty Gearboxes
Publikacja -
Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data.
PublikacjaW pracy przedstawiono analizę konstrukcji łożyska wzdłużnego turbiny wodnej. Łożysko zostało skonstruowane około 50 lat temu, a jego konstrukcja przewiduje kompensację termicznych odkształceń klocków. W analizie uwzględniono odkształcenia łożyska i wymianę ciepła w filmie smarowym i klockach łożyskowych. Poza obecną konstrukcją łożyska przeprowadzono również studium wpływu podstawowych parametrów konstrukcyjnych: grubości klocka...
-
Influence of hydrostatic pump operation period on performance of a thrust bearing of a 125 MW pump-turbine.
PublikacjaW pracy przedstawiono wyniki badań eksploatacyjnych łożysk wzdłużnych pompoturbin 125 MW elektrowni szczytowo pompowej (esp) Żar. W celu oceny warunków pracy łożysk wyposażono je w segmenty pomiarowe umożliwiające pomiary temperatury i położenia segmentu. W pracy omówiono konstrukcję i wyposażenie segmentu badawczego, metodykę wyznaczania charakterystycznych wielkości. Omówiono także wyniki badań wpływu czasu pracy pompy hydrostatycznego...
-
Justifying the prolongation of the service life of the bearing structure of a tank car when using Y25 bogies
PublikacjaThis paper substantiates the use of Y25 bogies under tank cars in order to prolong their service life. The reported study has been carried out for a tank car with rated parameters, as well as the actual ones, registered during full-scale research. Mathematical modeling was performed to determine the basic indicators of the tank car dynamics. The differential equations of motion were solved by a Runge-Kutta method using the Mathcad...
-
Assessment of possible application of water lubricated sintered brass slide bearing for marine propeller shaft
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych smarowanego wodą łożyska poprzecznego z panwią wykonaną ze spieku brązu.Przedstawiono wyniki pomiarów rozkładu ciśnienia w filmie smarnym, trajektorie osi wału oraz oporów ruchu.Przeprowadzono ocenę przydatności tego typu łożyska do łożyskowania okrętowych wałów śrubowych.
-
Comparison of induction motor bearing diagnostic test results through vibration and stator current measurement
PublikacjaThe paper discusses results of tests performed by authors, related to the angine bearings diagnostic using vibration and stator current measurements. The paper contains the description of an automatic measurement system, developed for measurement of those harmonics and processing that to obtain bearing diagnostic information. System was tested on objects with intentionally made defects in bearings, results of this test was also...