Filtry
wszystkich: 701
-
Katalog
Wyniki wyszukiwania dla: ŻÓŁTOWSKI
-
Selected aspects of performance of organic Rankine cycles incorporated into bioenergy with carbon capture and storage using gasification of sewage sludge
PublikacjaThe study aims to investigate the application of the Organic Rankine Cycle (ORC) in the bioenergy with carbon capture and storage (BECCS) using gasification of sewage sludge. The tool used in the investigation is the Aspen Plus software with REFPROP property methods for calculating fluid properties. The reason for this study is that a detailed analysis of the proposed BECCS process flow diagram indicates that a certain amount of...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublikacjaThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...
-
Energy conversion in systems-contained laser irradiated metallic nanoparticles - comparison of results from analytical solutions and numerical methods
PublikacjaThis work introduces the theoretical method of metallic nanoparticles’ (NPs’) heat and mass transfer where the particles are coated on a surface (base), together with considering the case wherein nanoparticles move freely in a pipe. In order to simulate the heat transfer, energy and radiative transfer equations are adjusted to the considered issue. NPs’ properties are determined following the nanofluidic theories, whereas absorption...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublikacjaThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Deterioration of masonry structure investigated by a thermal camera with a qualitative assessment of thermal image processing
PublikacjaThermal imaging is contemporary remote sensing measurement technique, which provides an image of the temperature distribution in the measured object. The method is widely used, due to its mobility as well as the non-destructive character of the measurement. Infrared thermography is especially relevant in the inspection of insulation, what is more, it is a suitable device for detecting thermal bridges and structural changes, which...
-
Deformation Analysis of a Composite Bridge during Proof Loading Using Point Cloud Processing
PublikacjaRemote sensing in structural diagnostics has recently been gaining attention. These techniques allow the creation of three-dimensional projections of the measured objects, and are relatively easy to use. One of the most popular branches of remote sensing is terrestrial laser scanning. Laser scanners are fast and efficient, gathering up to one million points per second. However, the weakness of terrestrial laser scanning is the...
-
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublikacjaMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
Błędy projektowe zewnetrznego szybu dźwigu osobowego oraz ich negatywny wpływ na eksploatację budynku przychodni
PublikacjaPo 25 latach eksploatacji budynku przychodni podjęto decyzję o jego przystosowaniu dla potrzeb osób niepełnosprawnych. W związku z tym opracowano projekt budowlany zewnętrznego, dostawianego do ściany szczytowej szybu widnowego. Szyb zaprojektowany został jako murowany z pustaków ceramicznych z poziomymi przewiązkami w poziomie stropów budynku przychodni, posadowiony na żelbetowej monolitycznej płycie fundamentowej o grubości 25...
-
Błedy projektowe oraz wykonawcze przyczyną uszkodzeń podłogi w pomieszczeniach nad tunelem
PublikacjaPrzedmiotem artykułu jest podłoga w pomieszczeniach znajdujących się nad tunelem kolejowym w wielkopowierzchniowym Centrum Handlowym. W wyniku błędów projektowych oraz wykonawczych podłoga nie spełniała warunków bezpieczeństwa konstrukcji oraz bezpieczeństwa użytkowania. Popełnione błędy były przyczyną awarii, a w przyszłości doprowadzić mogły do katastrofy budowlanej.
-
Assessment of Failure Occurrence Rate for Concrete Machine Foundations Used in Gas and Oil Industry by Machine Learning
PublikacjaConcrete machine foundations are structures that transfer loads from machines in operation to the ground. The design of such foundations requires a careful analysis of the static and dynamic effects caused by machine exploitation. There are also other substantial differences between ordinary concrete foundations and machine foundations, of which the main one is that machine foundations are separated from the building structure....
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublikacjaThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Computational Fluid Dynamics Simulation of Gas–Liquid Multiphase Flow in T-junction for CO2 Separation
PublikacjaThe article presents the results of a computational fluid dynamics (CFD) analysis of gas-liquid multiphase flow. The simulation was conducted using CFD code and the Euler–Euler approach. The presented study relates to the non–reactive, steady-state, turbulent flow of water and carbon dioxide mixture in a 3D pipe. Separation phenomenon between phases is observed. The solution was obtained using a mixture model. Different values...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Novel staphylococci nucH taxonomical marker used in identification of human-associated Staphylococcus succinus subsp. casei
PublikacjaThe aim of our study was to assess the sequencing of unique nucH gene fragment based on performed bioinformatics analysis as a novel diagnostic method for the identification of difficult to identify staphylococcal human pathogenic strains. Initially, PCR-RFLP-rrn analysis specific to the spacers between 16SrDNA and 23SrDNA followed by HhaI restriction analysis was performed. Further, sequencing of nucH and 16S rDNA genes fragments...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Carbon Dioxide Recovery Skid
PublikacjaIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Category-Based Workload Modeling for Hardware Load Prediction in Heterogeneous IaaS Cloud
PublikacjaThe paper presents a method of hardware load prediction using workload models based on application categories and high-level characteristics. Application of the method to the problem of optimization of virtual machine scheduling in a heterogeneous Infrastructure as a Service (IaaS) computing cloud is described.
-
POPRAWY ELASTYCZNOŚCI PRACY BLOKÓW PAROWYCH I GAZOWO-PAROWYCH PRZEZ ZASTOSOWANIE MAGAZYNU PARY
PublikacjaCelem niniejszej pracy jest krótki przegląd sposobów magazynowania energii i odniesienie się do sposobu, który byłby najdogodniejszy dla bloków zawodowych parowych i gazowo-parowych. W niniejszej pracy zaproponowano innowacyjny magazyn pary, który jest integralną częścią obiegu parowego, bądź gazowo-parowego i dzięki temu szybko odpowiada na zmiany zapotrzebowania na energię elektryczną, a zatem może usprawniać świadczenia usługi...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublikacjaThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
Lizostafyna - źródła otrzymywania i zastosowanie
PublikacjaW pracy przedstawiono ogólną charakterystykę liostafyny: budowę, właściwości biochemiczne, źródła otrzymywania enzymu. Przedstawiono także możliwości wykorzystania tego białka w medycynie i weterynarii jako alternatywny chemioterapeutyk przeciw infekcjom wywoływanym przez gronkowce oraz w przemyśle żywnościowym do poprawy mikrobiologicznej jakości produktów.
-
Modele 1D i 2D przepływu w pompie diagonalnej
PublikacjaW pracy przedstawiono nowe podejście do rozwiązania zadania konstrukcyjnego pompy w ramach modelu osiowo-symetrycznego typu 2D. Przykład obliczeniowy cytowany w artykule przedstawia wirnik pompy diagonalnej poddanej obliczeniom 3D.Przedstawiono także nowy sposób prezentacji procesu tłoczenia w pompie diagonalnej w ramach modelu 1D w postaci wykresu energia - straty energii.
-
Two dimensional inverse solution for diagonal pumps
PublikacjaW pracy przedstawiono rozwiązanie zadania odwrotnego dla wirnika i kierownicy pompy diagonalnej. Dla założonego kształtu powierzchni prądu wyznaczono kształt łopatek obu palisad. Geometria kanałów łopatkowych została wyznaczona w wyniku rozwiązania układu równań zapisanych w krzywoliniowym układzie współrzędnych. W pracy przedstawiono fotografie wirnika wykonanego techniką Rapid Prototyping.
-
System ratownictwa drogowego - stan obecny i konieczność rozwoju
PublikacjaW referacie przedstawiono zadania i projekty, które należy przygotować w celu usprawnienia systemu ratownictwa drogowego i systemu pomocy ofiarom wypadków drogowych.
-
Active carbons from waste biochars
Publikacja -
Effect of biochar activation by different methods on toxicity of soil contaminated by industrial activity
Publikacja -
Obiekty mostowe obwodnicy miasta Wolin w świetle badań podczas próbnego obciążenia.
Publikacja02 grudnia 2003r. oddano do eksploatacji obwodnicę miasta Wolin w ciągu drogi krajowej nr 3. Droga ta odgrywa ważną rolę w tranzytowym ruchu międzynarodowym (kraje skandynawskie - południe Europy) oraz krajowym (północ - południe). Obsługuje ona również port i bazy promowe w Świnoujściu. Nowa droga zlokalizowana w sąsiedztwie toru kolejowego, umożliwia bezkolizyjny przejazd przez miasto. Całkowita długość wybudowanego odcinka wynosi...
-
Wojciech Żółtowski
Osoby -
Bogdan Żółtowski
Osoby -
Enhanced energy conversion as a result of fluid-solid interaction in micro- and nanoscale
PublikacjaIt is known that nano- and micromechanics require new approaches to right describing of surface-like phenomena which lead to an enhanced energy conversion. In this work, a general form of surface forces that consist of a contribution from both the friction and mobility components has been extended to collect the effects of bulk and surface motion of a fluid. Quite similar impact can be observed for a solid-fluid mixture, where...
-
Maksymalna elastyczność pracy bloków parowych
PublikacjaW artykule przedstawiono propozycję przyspieszenia startów turbiny parowej poprzez właściwe doprowadzanie pary w trakcie stanów niestacjonarnych. Badano najbardziej wytężone miejsca w urządzeniu, przy uwzględnieniu tradycyjnej hipotezy Hubera-Missesa-Hencky, jak i hipotezy Burzyńskiego. W przypadku licznych startów coraz większe znaczenie odgrywają naprężenia termiczne, dla których najważniejsze są składowe normalne naprężeń, w...
-
Konstrukcje Betonowe II - BOs7 - N - 2022/23
Kursy Online -
Podstawy Konstrukcji Medycznych - IMM
Kursy OnlinePodstawy Konstrukcji Maszyn dotyczą metod projektowania i obliczania typowych elementów, z których składają się wszystkie maszyny i ich połączeń
-
Konstrukcje Betonowe 2 - KB2_BOs7_N_2023/24
Kursy Online -
Wpływ składu chemicznego na właściwości mechaniczne okrętowych pędników śrubowych z brązu BA1055
PublikacjaPrzedstawiono wyniki badań mikrostruktury oraz właściwości mechanicznych odlewów piaskowych z brązu BA1055 stosowanego do wyrobu pędników okrętowych. Przeanalizowano zależności właściwości mechanicznych od struktury i składu chemicznego brązu. Stwierdzono, iż optymalne właściwości mechaniczne uzyskują odlewy, w których stosunek ilości pierwiastków stopowych żelaza do niklu wynosi ok. 1,0.
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublikacjaThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublikacjaPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Accuracy improvement of the prestressed concrete structures precise geometry assessment by use of bubble micro-sampling algorithm
PublikacjaPrestressed concrete structures are well-known technology for a vast period, but nevertheless, this very technology is a leading solution, currently used in construction industry. Prestressed concrete structures have a huge advantage over conventional methods because it uses the properties of concrete in a very efficient way. The main idea behind this technology is to introduce into the cross-section of the structure, the internal...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublikacjaThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Method of selective fading as a educational tool to study the behaviour of prestressed concrete elements under excess loading
PublikacjaPrestressed structures are a key to realization of the boldest architectural ideas, characteristic feature of prestressed structure is better use of concrete material properties by insertion of internal forces. Learning about pre-stressed reinforced concrete structures is an integral part of Graduate Studies Program in construction engineering. Know-how of geometry change patterns in prestressed concrete elements under certain...
-
Исследование дистанционного зондирования железобетонных структурных элементов с помощью наземного лазерного сканирования
PublikacjaСовременная технология наземного лазерного сканирования (TLS) с помощью геодезических сканеров с диапазоном более 50 метров, способная измерять геометрию структурных элементов с точностью, близкой к 1 мм. Авторы, на основании лабораторных испытаний и собственного опыта, представляют способ, который позваляет оценить, первоначально, железобетонные балки как основной структурный элемент типа наведения мостов, путепроводов, коммерческих...
-
Исследование дистанционного зондирования железобетонных структурных элементов с помощью наземного лазерного сканирования
PublikacjaСовременная технология наземного лазерного сканирования (TLS) с помощью геодезических сканеров с диапазоном более 50 метров, способная измерять геометрию структурных элементов с точностью, близкой к 1 мм. Авторы, на основании лабораторных испытаний и собственного опыта, представляют способ, который позваляет оценить, первоначально, железобетонные балки как основной структурный элемент типа наведения мостов, путепроводов, коммерческих...
-
Zastosowanie naziemnego skaningu laserowego i przetwarzanie danych : Elementy żelbetowe
PublikacjaMonografia prezentuje wyniki badań nad wykorzystaniem naziemnego skaningu laserowego w pomiarach belek żelbetowych poddawanych niszczeniu. Publikacja składa się z 6 rozdziałów: Rozdział I: Wstęp do zagadnienia. Rozdział II: Zginane belki żelbetowe i mechanizm ich niszczenia. Rozdział III: Technologia naziemnego skaningu laserowego. Rozdział IV: Badania nad naziemnym skaningiem laserowym przy niszczeniu belek żelbetowych. Rozdział...
-
Model-Based Adaptive Machine Learning Approach in Concrete Mix Design
PublikacjaConcrete mix design is one of the most critical issues in concrete technology. This process aims to create a concrete mix which helps deliver concrete with desired features and quality. Contemporary requirements for concrete concern not only its structural properties, but also increasingly its production process and environmental friendliness, forcing concrete producers to use both chemically and technologically complex concrete...
-
Adaptation of the arbitrary Lagrange–Euler approach to fluid–solid interaction on an example of high velocity flow over thin platelet
PublikacjaThe aim of this study is to analyse the behaviour of a thin plate with air flow velocities of 0.3–0.9 Ma. Data from the experiment and numerical tools were used for the analysis. For fluid–solid interaction calculations, the arbitrary Lagrange–Euler approach was used. The results of the measurements are twofold. The first one is the measurement of the flow before and after vibrating plate, i.e. pure flow plate, and the second consists...
-
Analysis of electricity generation variability in 2019 with special consideration of electrical energy generation from wind sources.
PublikacjaThis article presents issues related to the broadly understood development of wind energy. The state of the art of wind energy in the world has been discussed. This paper also shows issues related to factors affecting the development of renewable energy sources and their impact on the natural environment on the basis of available research. The focus is, however, on the critical analysis of phenomena in the data of the Transmission...
-
Discrimination of hospital isolates of Acinetobacter baumannii using repeated sequences and whole genome alignment differential analysis
PublikacjaAn optimized method for bacterial strain differentiation, based on combination of Repeated Sequences and Whole Genome Alignment Differential Analysis (RS&WGADA), is presented in this report. In this analysis, 51 Acinetobacter baumannii multidrug-resistance strains from one hospital environment and patients from 14 hospital wards were classified on the basis of polymorphisms of repeated sequences located in CRISPR region, variation...
-
Framework for Structural Health Monitoring of Steel Bridges by Computer Vision
PublikacjaThe monitoring of a structural condition of steel bridges is an important issue. Good condition of infrastructure facilities ensures the safety and economic well-being of society. At the same time, due to the continuous development, rising wealth of the society and socio-economic integration of countries, the number of infrastructural objects is growing. Therefore, there is a need to introduce an easy-to-use and relatively low-cost...