Filtry
wszystkich: 1984
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CONSECUTIVE COLORING
-
Natural convective heat-transfers from an isothermal horizontal hemispherical cavity
PublikacjaPrzedstawiono rozwiązanie analityczne oraz wyniki badań eksperymentalnych i numerycznych konwekcyjnej wymiany ciepła od poziomej izotermicznej kulistej wklęsłej powierzchni.
-
A theoretical consideration of a free convective boundary layer on an isothermal horizontal conic.
PublikacjaPrzedstawiono rozwiązanie analityczne naturalnej konwekcji swobodnej od izotermicznego, poziomego stożka o kącie przy podstawie alfa. Rozwiązanie przeprowadzono w oparciu o typowe dla konwekcji swobodnej założenia upraszczające. Rozwiązania dla przypadków granicznych (poziomy walec i pionowa płyta kołowa) wykazują dobrą zgodność z danymi literaturowymi.
-
Empirical Relationship Describing Total Convective and Radiative Heat Loss in Buildings
PublikacjaOn the basis of theoretical considerations of convective-radiative heat transfer, a relationship was developed enabling the total convective and radiative heat flux QC+R emitted from any object at tw and its surroundings at t∞ to be calculated from known values of the surface temperature of such an object, i.e., the known temperature difference Δt=tw - t∞ and average air temperature Tav. This relationship is applied to thermal...
-
Equitable colorings of some variation of corona products of cubic graphs
PublikacjaThe problem of determining the value of equitable chromatic number for multicoronas of cubic graphs is studied. We provide some polynomially solvable cases of cubical multicoronas and give simple linear time algorithms for equitable coloring of such graphs which use almost optimal number of colors in the remaining cases.
-
Long-Term Trends in Shooting Performance in the NBA: An Analysis of Two- and Three-Point Shooting across 40 Consecutive Seasons
Publikacja -
Comparison of GPS tropospheric delays derived from two consecutive EPN reprocessing campaigns from the point of view of climate monitoring
PublikacjaThe main purpose of this research was to acquire information about consistency of ZTD (zenith total delay) linear trends and seasonal components between two consecutive GPS reprocessing campaigns. The analysis concerned two sets of the ZTD time series which were estimated during EUREF (Reference Frame Sub-Commission for Europe) EPN (Permanent Network) reprocessing campaigns according to 2008 and 2015 MUT AC (Military University...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Experimental verification of natural convective heat transfer phenomenon from isothermal cuboids
PublikacjaArtykuł przedstawia wyniki badań eksperymentalnych konwekcyjnej wymiany ciepła od powierzchni izotermicznego prostopadłościanu o stosunkowo dużych rozmiarach (t.j. 1.5 m x1 m x 0.5 m). Celem tych badań było otrzymanie wyników, które można by porównać z otrzymanymi dla obiektu w mniejszej skali i prezentowano we wcześniejszych doniesieniach (Int. J. Heat Mass Transfer 46 (2003) 2169-2178). Rozwiązanie eksperymentalne przeprowadzono...
-
The effect of plate size on the natural convective heat transfer intensity of horizontal surfaces
PublikacjaW pracy przedstawiono badania wpływu rozmiarów płyty prostokątnej poziomej na intensywność wymiany ciepła w warunkach konwekcji swobodnej. Zaproponowano dwa zakresy: dla płyt o wymiarze charakterystycznym mniejszym niż 0,1 m - 0,2 m intensywność konwekcyjnej wymiany ciepła jest odwrotnie proporcjonalna do szerokości płyty, dla płyt szerszych niż 0,2 m szerokość płyty nie wpływa znacząco na współczynnik konwekcyjnej wymiany ciepła....
-
Marek Kubale prof. dr hab. inż.
OsobyDetails concerning: Qualifications, Experiences, Editorial boards, Ph.D. theses supervised, Books, and Recent articles can be found at http://eti.pg.edu.pl/katedra-algorytmow-i-modelowania-systemow/Marek_KubaleGoogle ScholarSylwetka prof. Marka Kubalego Prof. Marek Kubale pracuje na Wydziale ETI Politechniki Gdańskiej nieprzerwanie od roku 1969. W tym czasie napisał ponad 150 prac naukowych, w tym ponad 40 z listy JCR. Ponadto...
-
Stem Cells and Cloning-Advances and Applications
Czasopisma -
The new concept of product. Cooling band
PublikacjaThe chapter below presents the innovative solution consist in applying the cooling band to help holding the hot object. The solution was found through substitute inputs analysis and brain storm method. The new product was submitted in Polish Patent Office under the No. W.120905.
-
Study of free convective boundary layer of isothermal lateral surface of axisymmetrical horizontal body
PublikacjaPrzedstawiono rozwiązanie równań Naviera-Stokesa i Fouriera-Kirchhoffa we współrzędnych tau i sigma. Pierwsza jest styczną a druga normalną do konwekcyjnych linii prądu, wzdłuż jakich porusza się ogrzany od powierzchni płyn. Wynik w postaci równania na grubość warstwy przyściennej zweryfikowano dla granicznych przypadków ciała obrotowego o poziomej osi symetrii (stożka poziomego i kołowej pionowej płyty).
-
Free convective heat transfer structures as a function of the width of isothermal horizontal rectangular plates
PublikacjaZaprezentowano rezultaty badań eksperymentalnych konwekcyjnej wymiany ciepła od izotermicznych płyt prostokątnych skierowanych ku górze. Na podstawie przeprowadzonych wizualizacji zaproponowano dwa modele struktur przepływu. Rozwiązania analityczne dla tych modeli przedstawiono w postaci zależności liczb Nusselta Rayleigh'a. Stwierdzono, że przepływ koncentryczny występuje dla małych wartości liczb Ra, szczególnie w przypadku płyt...
-
Natural convective heat transfer from isothermal horizontal, vertical and inclined plates - a review
PublikacjaW artykule przedstawiono przegląd otrzymanych przez różnych badaczy korelacji eksperymentalych, teoretycznych i numerycznych, opisujących wymianę ciepła od izotermicznych płyt o różnym kącie pochylenia. Przedstawiono model matematyczny zjawiska. Opisano stosowane metody badawcze i wskazano przyczyny rozbieżności pomiędzy przedstawionymi przez wielu autorów wynikami.
-
The effect of convective heating and microwave heating on antioxidant enzymes in pooled mature human milk
PublikacjaThe effects of convective and microwave heating at constant temperature (62.5, 66 and 70 °C) on the activity of antioxidant enzymes (superoxide dismutase, SOD; catalase, CAT; glutathione peroxidase, GPx) in pooled mature human milk were compared. Activities of the enzymes were determined using spectrophotometric kits. Activity of GPx decreased significantly in the first stage of heating when milk samples were warmed to pasteurisation...
-
An interval estimator for chlorine monitoring in drinking water distribution systems under uncertain system dynamics, inputs and chlorine concentration measurement errors
PublikacjaThe design of an interval observer for estimation of unmeasured state variables with application to drinking water distribution systems is described. In particular, the design process of such an observer is considered for estimation of the water quality described by the concentration of free chlorine. The interval observer is derived to produce the robust interval bounds on the estimated water quality state variables. The stability...
-
Non-disjoint Decomposition Using r-admissibility and Graph Coloring and Its Application in Index Generation Functions Minimization
Publikacja -
Investigation of electrocatalytic gas sensor properties in presence of chlorine
PublikacjaProperties of sensor based on Nasicon with two round shaped platinum electrodes are investigated. Influence of different chlorine concentrations on the sensor response is presented. Measurements in different temperatures have been performed in order to determine optimal sensor working temperature.
-
The aluminium and polycarbonate covering of the canopy above the stadium in Gdansk
PublikacjaW artykule przestawiono informacje o elementach konstrukcyjnych poszycia zadaszenia stadionu piłkarskiego w Gdańsku zrealizowanego z okazji rozgrywanych w Polsce i Ukrainie mistrzostw Europy w piłce nożnej. Omówione zostały elementy poszycia z poliwęglanu wraz z jego konstrukcją nośną oraz układem odwodnienia. Podano informacje o testach i badaniach przeprowadzonych przed wykonaniem obiektu, które zadecydowały o przyjętych rozwiązaniach...
-
The aluminium and polycarbonate covering to the roof over the stadium in Gdańsk
PublikacjaThis paper presents information about structural elements of the roof covering to the stadium in Gdansk built for the 2012 European Football Championship in Poland and the Ukraine. The paper discusses elements of the polycarbonate covering, the supporting structure and the drainage system. It also provides information about tests and research performed prior to construction, which determined the solutions adopted as well as...
-
Investigation of electrocatalytic gas sensor properties in presence of chlorine
PublikacjaIn this paper performance of an electrocatalytic sensor in presence of chlorine is investigated. Presented studies concern sensor prepared in ceramic technology based on NASICON as a solid electrolyte with two round shaped platinum electrodes. Measurements in different temperatures have been performed in order to determine optimal sensor working temperature.
-
Advanced Macromodel Matrix Structure Cloning for FDTD
PublikacjaWe propose an improved macromodel-based techniquefor efficient analysis of the structures based on PhotonicCrystals (PhC). The technique involves a new structure of thecoupling matrix and advanced cloning of not only the macromodel matrices, but also the coupling matrices SE and SH.The method allows one to shorten considerably the preprocessingtime, the RAM usage and also the iterating speed of performingFDTD. With this...
-
Cooling of electronic equipment by means of jets and microjets
PublikacjaW pracy przedstawiono rozwiązanie sprzężonej wymiany ciepła od uderzającej strugi cieczy oraz przewodzenia ciepła w łytce. Uzyskano proste zależności opisujące rozkład temperatur na płytce. Umożliwia to przeprowadzenie analizy wpływu różnych parametró na wymianę ciepła podczas chłodzenia urządzeń elektronicznych generujących ciepło.
-
Performance of a hybrid microjet – microchannel cooling module
PublikacjaThe paper presents the experimental investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary...
-
New generation cooling systems for car engines
PublikacjaNormy czystości spalin silników samochodowych wymusiły rozwój elektronicznego sterowania pracą silników samochodowych. Do niedawna układy chłodzenia były bardzo tradycyjnymi - niesterowanymi programowo. W artykule przedstawiono możliwości wprowadzenia zaawansowanego sterowania mikroprocesorowego do układów chłodzenia silników spalinowych. Rozważania zilustrowano badaniami z literatury i własnymi pomiarami autora.
-
Some aspects surface cooling by impinging jet
PublikacjaW pracy przedstawiono wyniki badań wymiany ciepła, uskoku hydraulicznego i stabilności podczas napływu strugi na powierzchnię ciała stałego.
-
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Development trends of automotive engine cooling systems
PublikacjaDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Modeling of the internal combustion engine cooling system
PublikacjaThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
ATTEMPTS OF THERMAL IMAGING CAMERA USAGE IN ESTIMATIONS OF THE CONVECTIVE HEAT LOSS FROM A VERTICAL PLATE
PublikacjaIn this paper a new method for determining heat transfer coefficients using a gradient method has been developed. To verify accuracy of the proposed method vertical isothermal heating plate with natural convection mechanism has been examined. This configuration was deliberately chosen, because of the fact that such case is historically the earliest and most thoroughly studied and its rich scientific documentation - the most reliable....
-
Quantitative study of free convective heat losses from thermodynamic partitions using Thermal Imaging
PublikacjaThe following paper presents a simple method of determining the presence, distribution and values of heat losses from external building walls as thermodynamic partitions using a Thermal Imaging Camera (TIC). According to Fourier's equation, the value of heat loss is proportional to the temperature gradient ∂t/∂y|y=0 in air in the y direction perpendicular to the heated surface. Unfortunately, air temperature cannot be measured...
-
The selected roof covering technologies in the aspect of their life cycle costs
PublikacjaIn the article is presented an analysis of the life cycle costs calculation for selected roof coverings. The scope of research includes costs of construction, maintenance and demolition of the roof covering structure for two alternative technologies – the traditional and new generation. On the presented example of an industrial building with a roof area of 1000 m², the above costs are taken to consideration for the roof covering...
-
Rheology of Variable Viscosity‐Based Mixed Convective Inclined Magnetized Cross Nanofluid with Varying Thermal Conductivity
PublikacjaCross nanofluid possesses an extraordinary quality among the various fluidic models to explore the key characteristics of flowing fluid during very low and very high shear rates and its viscosity models depend upon shear rate. The current study establishes the numerical treatment regarding variable viscosity‐based mixed convective inclined magnetized Cross nanofluid with var‐ ying thermal conductivities over the moving permeable...
-
Advancement of Non-Newtonian Fluid with Hybrid Nanoparticles in a Convective Channel and Prabhakar’s Fractional Derivative—Analytical Solution
Publikacja -
Experimental and theoretical investigation of microjet cooling in metalurgical applications
PublikacjaW pracy zaprezentowano model wrzącej strugi uderzającej o powierzchnię i wytwarzającej cienki film cieczowy, w którym tworzą się pęcherzyki pary.
-
The automation of test stand for engine cooling system testing
PublikacjaW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
Active management of equipment cooling in hoteling data centers
PublikacjaHoteling data centers are designated for housing computing and storage units of many, usually small customers, as opposed to traditional data centers supporting own computing and storage resources of a bigger company. One of the services to be provided to consumer’s equipment is cooling. Cooling in data centers is prevalently achieved by circulating air in computer room. Efficient cooling requires delivering cold air from central...
-
Effects of cooking on the bioactivity of lotus roots and white onions
PublikacjaW pracy przedstawiono wyniki badań wpływu obróbki termicznej (gotowanie) na zawartość związków bioaktywnych i potencjału przeciwutleniającego korzenia lotosu i cebuli białej.Wyniki badań jednoznacznie wskazują na fakt, że taki proces obróbki wpływa w znaczącym stopniu na spadek stężenia związków bioaktywnych i potencjału przeciwutleniającego.
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
A System for Cooling Electronic Elements with EHD Coolant Flow
PublikacjaA system for cooling electronic components where the liquid coolant flow is forced with ion-drag type EHD micropumps was tested.
-
The saga of a fish: from a survival guide to closing lemmas
PublikacjaIn the paper by D. Burago, S. Ivanov and A. Novikov, “A survival guide for feeble fish”, it has been shown that a fish with limited velocity can reach any point in the (possibly unbounded) ocean provided that the fluid velocity field is incompressible, bounded and has vanishing mean drift. This result extends some known global controllability theorems though being substantially nonconstructive. We give a fish a different recipe...
-
Theoretical consideration of free convective heat transfer from a round isothermal plate slightly inclined from the vertical
PublikacjaA semi-analytical solution of simplified Navier-Stokes and Fourier-Kirchhoff equations describing free convective heat transfer from a round isothermal surface slightly inclined from the vertical is presented. The solution is based on the assumption, typical for natural convection, that the velocity component normal to the surface is negligibly small in comparison to the tangential one. Next we neglect the nonlinear inertia force...
-
Innovative Turbine Intake Air Cooling Systems and Their Rational Designing
PublikacjaThe improved methodology of the engine intake air cooling system designing based on the annual effect due to cooling was developed. It involves determining the optimal value of cooling capacity, providing the minimum system sizes at maximum rate of annual effect increment, and its rational value, providing a close to maximum annual effect without system oversizing at the second maximum rate of annual effect increment within the...
-
Sodium nitrite as a corrosion inhibitor of copper in simulated cooling water
PublikacjaThe corrosion inhibition behavior of sodium nitrite (NaNO2) towards pure copper (99.95%) in simulated cooling water (SCW) was investigated by means of electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). NaNO2 interferes with metal dissolution and reduce the corrosion rate through the formation or maintenance of inhibitive film on the metal surface. Surface morphologies illustrated...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublikacjaA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Experimental and theoretical study of surface cooling using a single microjet
PublikacjaPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
Anchoring and mooring equipment for a two-segment inland waterways ship
PublikacjaW artykule dokonano przeglądu i analizy wyposażenia kotwiczno-cumowniczego współczesnych statków śródlądowych. Przedstawiono także propozycję takiego wyposażenia dla segmentowego statku pasażerskiego wraz z doborem i rozmieszczeniem na pokładzie poszczególnych urządzeń.