Publikacje
Filtry
wszystkich: 146
Katalog Publikacji
Rok 2023
-
Energy conversion in systems-contained laser irradiated metallic nanoparticles - comparison of results from analytical solutions and numerical methods
PublikacjaThis work introduces the theoretical method of metallic nanoparticles’ (NPs’) heat and mass transfer where the particles are coated on a surface (base), together with considering the case wherein nanoparticles move freely in a pipe. In order to simulate the heat transfer, energy and radiative transfer equations are adjusted to the considered issue. NPs’ properties are determined following the nanofluidic theories, whereas absorption...
-
Estimation of the Regenerative Braking Process Efficiency in Electric Vehicles
PublikacjaIn electric and hybrid vehicles, it is possible to recover energy from the braking process and reuse it to drive the vehicle using the batteries installed on-board. In the conditions of city traffic, the energy dissipated in the braking process constitutes a very large share of the total resistance to vehicle motion. Efficient use of the energy from the braking process enables a significant reduction of fuel and electricity consumption...
-
Evaluation of the energy efficiency of electric vehicle drivetrains under urban operating conditions
PublikacjaIn electric vehicles, as in hybrids vehicles, a very important factor affecting the energy efficiency of the powertrain is the ability to use the regenerative braking energy. Depending on the settings available in electric vehicles, the driver can choose different modes of operation: switch off the regenerative braking mode altogether, select the intensity of regenerative braking, or leave the control system in automatic mode....
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublikacjaAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublikacjaA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublikacjaThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Experimental Investigation of the Performance of an Innovative Implantable Left Ventricular Assist Device—Proof of Concept
PublikacjaThis paper presents the results of experimental performance of an innovative left ventricular assist device working on a specially designed test stand. The introduced invention is mainly applied for supporting the heart in patients with end-stage heart failure accompanied by mitral valve regurgitation and pulmonary hypertension. Moreover, the developed device has the form of a flexible balloon forming an intracardiac inert gas-filled...
-
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Experimental Study of Polish Sausage Drying Kinetics and Contraction by Image Data Analysis
PublikacjaThe goal of this paper has been to add an experimental data set for drying a meat product and provide a comparison with well-established thin-layer drying models. This article presented experimental investigations on the convective drying of Polish sausage slices at a temperature of 40°C. Slices have been in the thickness of 3 to 8mm. Measurements of mass loss and size change were performed. The data have been presented in the...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Flow Maps and Flow Patterns of R1233zd(E) in a Circular Minichannel at Low, Medium and High Values of Saturation Pressure
PublikacjaThere is a gap in knowledge regarding the flow pattern of low-boiling working fluids in the range of high saturation temperatures (above 120°C) and medium and high reduced pressures (0.5-0.9). Data are present in the literature for similar values of reduced pressures, but for lower values of saturation temperature. This is due to the existing refrigeration applications of these working fluids. At high values of reduced pressure,...
-
FORECASTING BIOGAS FORMATION IN LANDFILLS
Publikacja: The aim of the present research was to develop a mathematical model for estimating the amount of viscous gas generated as a function of weather conditions. Due to the lack of models for predicting gas formation caused by sudden changes in weather conditions in the literature, such a model was developed in this study using the parameters of landfills recorded for over a year. The effect of temperature on landfill gas production...
-
Fuel systems of high power stationary engine
PublikacjaThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublikacjaThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublikacjaThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
Innovative Implantable Left Ventricular Assist Device—Performance under Various Resistances and Operating Frequency Conditions
PublikacjaThis paper presents the operation of an innovative left ventricular assist device under various resistances and operating frequencies. The operating principle of the device is based on pulsatile blood flow, which is forced by a suction–discharge device pumping helium into a set of intra-cardiac balloons. In this way, the ejection fraction of the left ventricle is increased, and the mitral valve is additionally occluded. What is...
-
Metoda diagnostyki cieplno-przepływowej turbin parowych wykorzystująca elementy algorytmów genetycznych
PublikacjaRozprawa doktorska poświęcona jest opisowi budowania metody diagnostyki cieplno-przepływowej z wykorzystaniem elementów algorytmów genetycznych. Do tworzenia założeń i algorytmów metody posłużono się przykładem funkcjonowania bloku elektrowni kondensacyjnej ze szczególnym uwzględnieniem układu łopatkowego turbiny parowej. Celem pracy jest zbudowanie metody diagnostyki cieplno-przepływowej. Zadaniem metody jest przeprowadzenie procesu...
-
Modeling of entrained flow steam gasification of sewage sludge
PublikacjaProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublikacjaThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublikacjaDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublikacjaOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Numerical analysis of the ostiomeatal complex aeration using the CFD method
PublikacjaWe aimed to analyse ostiomeatal complex (OMC) aeration using the computational fluid dynamics (CFD) method of simulation based on human craniofacial computed tomography (CT) scans. The analysis was based on CT images of 2 patients: one with normal nose anatomy and one with nasal septal deviation (NSD). The Reynolds-Average Simulation approach and turbulence model based on linear eddy viscosity supplemented with the two-equation...
Rok 2022
-
Entrained Flow Plasma Gasification of Sewage Sludge–Proof-of-Concept and Fate of Inorganics
PublikacjaSewage sludge is a residue of wastewater processing that is biologically active and consists of water, organic matter, including dead and living pathogens, polycyclic aromatic hydrocarbons, and heavy metals, as well as organic and inorganic pollutants. Landfilling is on the decline, giving way to more environmentally friendly utilisation routes. This paper presents the results of a two-stage gasification–vitrification system, using...
-
Experiments on compression ignition engine powered by nano-fuels
PublikacjaThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
From fluid mechanics backgrounds to modern field theory
PublikacjaOur presentation keeps a historical line of reasoning, since we start from old concepts of fluid mechanics and finish on concepts of modern field theory. We want to show that some facts from the nature phenomena, which have firstly been discovered on the ground of fluid mechanics, were next incorporated into physics and later become the important pattern for whole mathematical physics. Especially, well-known continuum models, which...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Mathematical modelling of gasification process of sewage sludge in reactor of negative CO2 emission power plant
PublikacjaSewage sludge is a residue of wastewater processing that is biologically active and consists of water,organic matter, including dead and alive pathogens, as well as organic and inorganic contaminants suchas polycyclic aromatic hydrocarbons (PAHs) and heavy metals. Due to the nature of sewage sludge and itspossible influence on human health and wellbeing, it is a subject of various regulations. Currently,sewage sludge is considered...
-
Maxillary sinus aeration analysis using computational fluid dynamics
PublikacjaThe maxillary sinus aeration using the computational fluid dynamics (CFD) method based on individual adult patients’ computed tomography (CT) scans were analyzed. The analysis was based on CT images of 4 patients: one with normal nose anatomy and three with nasal septal deviation (NSD) and concha bullosa (CB). The CFD simulation was performed using the Reynolds-Average Simulation approach and turbulence closure based on linear...
-
Method of reconstructing two-dimensional velocity fields on the basis of temperature field values measured with a thermal imaging camera
PublikacjaThis paper describes a novel numerical reconstruction procedure (NRP) of the velocity field during natural convective heat transfer from a two-sided, isothermal, heated vertical plate based only on the known temperature field obtained, e.g. with a thermal imaging camera. It has been demonstrated that with a knowledge of temperature distributions, the NRP enables the reconstruction of velocity fields by solving the Navier-Stokes...
-
Metoda neuronowego wyznaczania przestrzennych pól przepływów w przydźwiękowych i naddźwiękowych kanałach łopatkowych turbin parowych
PublikacjaNiniejsza rozprawa doktorska została poświęcona opracowaniu metody neuronowego wyznaczania przestrzennych pól przepływów w okołodźwiękowych kanałach łopatkowych turbin parowych. Obiektem badań naukowych przedstawionych w kolejnych rozdziałach są dwa ostatnie stopnie części niskoprężnej turbozespołu 18K370 z wylotem ND-37. Pierwszym etapem badań była budowa numerycznego modelu przepływu pary mokrej przez analizowany układ łopatkowy....
-
Modelowanie wymiany ciepła przy wrzeniu w przepływie w warunkach podwyższonego ciśnienia zredukowanego dla R1233zd(E) jako potencjalnego czynnika w układach ORC [w:] Postępy w badaniach wymiany ciepła i masy
PublikacjaProces wrzenia w wysokotemperaturowych pompach ciepła oraz układach ORC zachodzi przy temperaturach wyższych niż 80˚C. W literaturze występuje luka w wiedzy dla podwyższonych temperatur nasycenia oraz korespondujących wysokich ciśnień zredukowanych. Większość istniejących danych doświadczalnych dotyczy temperatur niższych niż 40 ˚C, co związane jest z zastosowaniami chłodniczymi czynników niskowrzących. Dla temperatur wyższych...
-
Monitoring the gas turbine start-up phase on the platform using a hierarchical model based on Multi-Layer Perceptron networks
PublikacjaVery often, the operation of diagnostic systems is related to the evaluation of process functionality, where the diagnostics is carried out using reference models prepared on the basis of the process description in the nominal state. The main goal of the work is to develop a hierarchical gas turbine reference model for the estimation of start-up parameters based on multi-layer perceptron neural networks. A functional decomposition...
-
Multiple jets impingement – numerical analysis by the ζ-f and hybrid VLES turbulence models
PublikacjaPresented paper summarizes the Authors findings referring to the numerical analyses of the jet impinging phenomena in the case of complex jets configurations in various applications e.g. in the heat exchangers. Multiple jets interference resulting in the cross-flow and the surface curvature are the factors which impose the need of advanced turbulence models utilization. The outcome of the research based on the ζ-f turbulence model...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
Rok 2021
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Gasification of Densified Biomass (DB) and Municipal Solid Wastes (MSW) Using HTA/SG Technology
PublikacjaThe necessity of economical and rational use of natural energy sources caused a rapid development of research on the possibilities of using non‐conventional energy resources. Taking the above into account, a new technological process of thermochemical conversion of biomass and communal waste, commonly known as High Temperature Air/Steam Gasification (HTA/SG) and Multi‐Staged Enthalpy Extraction Technology (HTAG‐MEET), was developed....
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublikacjaThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
Minichannel and minigap classification criteria based on the aspect ratio of the minigeometry: A numerical study
PublikacjaA detailed numerical investigation has been carried out to analyze the diabatic flow distribution and velocity profile in 18 minigeometries with various aspect ratios for V-type and I-type flow configurations (for 36 cases) assuming ethanol as a working fluid. The aim of the study is to distinguish the value of the aspect ratio for which the flow in minigeometry starts to be two-dimensional (minigap). Cases with a constant Reynolds...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublikacjaWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
Rok 2024
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublikacjaThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Impacts of Using Exhaust Gas Recirculation and Various Amount of Dimethyl Ether Premixed Ratios on Combustion and Emissions on a Dual-Fuel Compression Ignition Engine
PublikacjaIn the presented research, the authors dealt with the specific properties of the combustion process of dimethyl ether (DME) in a combustion car (Volkswagen Golf IV) engine AJM 1.9 TDI PDE made by Volkswagen factory. Dimethyl ether is an alternative fuel produced most often from natural gas, which can be used in compression ignition engines as a single fuel or co-burned with diesel oil. This work describes the impacts of using exhaust...
Rok 2019
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublikacjaThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublikacjaThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
Rok 2012
-
Maszyny Hydrotechniczne Kanału Elblaskiego cz. 2.
PublikacjaPierwszy projekt kanału z 1827 roku, autorstwa Tajnego Radcy Budowlanego Severina z Kwidzyna, zakładał wyrównanie poziomów luster wody w jeziorach. Jezioro Jeziorak, koło Iławy, było największym jeziorem regionu, liczyło ponad 30 km długości, zatem uznano, że jego poziom wody będzie bazowym dla pozostałych jezior. Uznano również, że Miejscowość Miłomłyn, będzie głównym węzłem komunikacyjnym na kanale, stąd bowiem będą rozchodziły...
-
Maszyny hydrotechniczne Kanału Elbląskiego cz. 1.
PublikacjaHistoria ta zdarzyła się wiele lat temu. W czasach, gdy jeszcze na świecie nie było komputerów, elektryczności, silników spalinowych i tego wszystkiego bez czego teraz nie potrafimy żyć i egzystować. Wydawało by się, że tym bardziej ludzie żyjący wiele lad przed nami, nie mogli sobie poradzić z przeciwnościami natury, nie mając tych wszystkich dobrodziejstw techniki, którymi my tak łatwo na co dzień się posługujemy. Ale czy...