Filters
total: 1101
filtered: 742
Search results for: ship
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublicationThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
Cargo ships heat demand - operational experiment
PublicationThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
A numerical model to simulate the motion of a lifesaving module during its launching from the ship’s stern ramp
PublicationThe article presents a numerical model of object motion in six degrees of freedom (DoF) which is intended to be used to simulate 3D motion of a lifesaving module during its launching from a ship using a stern ramp in rough sea. The model, of relatively high complexity, takes into account both the motion of the ship on water in changing sea conditions, and the relative motion of the ramp with respect to the ship. The motion of the...
-
A risk comparison framework for autonomous ships navigation
PublicationMaritime autonomous surface ships (MASS) may operate in three predefined operational modes (OM): manual, remote, or autonomous control. Determining the appropriate OM for MASS is important for operators and competent authorities that monitor and regulate maritime traffic in given areas. However, a science-based approach to this respect is currently unavailable. To assist the selection of the proper OM, this study presents a risk-based...
-
Modeling of Accidental Bunker Oil Spills as a Result of Ship's Bunker Tanks Rupture - a Case Study
PublicationAIS (Automatic Identification System) data analysis is used to define ship domain for grounding scenarios. The domain has been divided into two areas as inner and outer domains. Inner domain has clear border, which is based on ship dynamic characteristics. Violation of inner domain makes the grounding accident unavoidable. Outer domain area is defined with AIS data analyzing. Outer domain shows the situation of own ship in compare...
-
Spectral analysis of nonstationary low-frequency magnetic-field emissions from ship's power
Publication -
CBR methodology application in an expert system for aided design ship's engine room automation
PublicationW artykule przedstawiono metody obliczania podobieństwa na podstawie przypadków, zastosowane w opracowanym systemie ekspertowym do wspomagania projektowania siłowni okrętowej. Do realizacji metody na przykładzie automatyki napędu głównego zastosowano oprogramowanie bazy danych i system ekspertowy. Uzyskane wyniki wyszukiwania w bazie danych statków podobnych zostały porównane i przeanalizowane. Do weryfikacji zastosowanych w bazie...
-
Measurement Of The Dynamics Of The Sheave Block Of Shipyard Crane With 1000 T Lifting Capacity For Verification Of The Laboratory Stand
Publication -
Interdisciplinary research as a form of monument protection and preparation for the investment process on the example of the former Gdańsk Shipyard complex
PublicationThe multi-layered heritage of many industrial plants operating until the end of the 20th century creates a particular challenge for conservators, designers and investors. In the process of protecting its values, displaying qualities and managing the property, it is necessary to recognize a wider transformation of technology of the entire plant and the individual functions of its buildings, as well as the context of intangible...
-
Minimization of a ship's magnetic signature under external field conditions using a multi-dipole model
PublicationThe paper addresses the innovative issue of minimizing the ship's magnetic signature under any external field conditions, i.e., for arbitrary values of ambient field modulus and magnetic inclination. Varying values of the external field, depending on the current geographical location, affect only the induced part of ship's magnetization. A practical problem in minimizing the ship signature is separating permanent magnetization...
-
A parametric method for evaluation of resistance of swath ships
PublicationArtykuł zawiera sformułowania metody parametrycznej służącej do wyznaczania oporu kadłuba statku o konfiguracji swath. Metodę opracowano opierając się na rezultatach obliczeń numerycznych, uzyskanych metodami strukturalnymi, wywiedzionymi ze sformułowań teoretycznej hydromechaniki okrętu, wykonanych na dostatecznie licznej serii kształtów kadłuba, o systematycznie uzmiennianych parametrach kształtu. Następnie przedstawiono rezultaty...
-
A model of risk for assessment of ships in damaged conditions
PublicationW pracy omówiono problemy związane z modelowaniem zagrożeń, konsekwencji i ryzyka, w metodzie oceny bezpieczeństwa statków w stanie uszkodzonym. W celu dokonania oceny bezpieczeństwa statku, w metodzie zastosowano podejścia oparte na ocenie zachowania się statku i ocenie ryzyka. Podejście oparte na ocenie zachowania się statku związane jest z oceną charakterystyk hydromechanicznych statku w stanie uszkodzonych w warunkach zbliżonych...
-
Optical Fibre, Local Measurement Systems For Ships
Publication -
Estimating operability of ships in ridged ice fields
Publication -
Investigations of transverse stability of semi-displacement ships
PublicationPrzedstawiono wyniki eksperymentalnych badań modelowych poprzecznej stateczności jednostek półślizgowych, których celem było określenie wpływu prędkości oraz parametrów kształtu kadłuba na stateczność poprzeczną. Na podstawie wyników badań opracowano algorytmy, uwzględniające zmiany ramienia prostującego w funkcji prędkości, kąta przechyłu i parametrów geometrycznych kadłuba które mogą być wykorzystane do oceny stateczności poprzecznej...
-
METHOD OF ROUTING SHIPS SAILING IN DEDICATED ENVIRONMENT
PublicationThe method for determining the suboptimal route of sailing vessels operating in a restricted area of the sea are proposed in the paper. The dynamics of the environment including weather conditions and speed characteristics of ships sailing are considered. As optimiza-tion criterion, measure sailing time T, and the number of maneuvers performed ω, are taken into account. An heuristic algorithm, and the appropriate application routing...
-
Revitalization of the Narrow-Gauge Żuławy Commuter Railway and its effect on shipping conditions in the Vistula delta
PublicationThe article presents the Żuławy Access Railway and the effect of its revitalization on the change of navigational conditions in the Vistula delta. One of the problems analyzed in the article is the intersection of two different transport branches - the inland waterway and rail transport branches. A solution to the problem of their functioning is presented, without any major restrictions. Possible changes in navigational conditions...
-
Impact of thermal loading into the structural performance of ships: A review
PublicationThe presented study reviews the recent advances done regarding the impact of thermal loading on the structural performance of ships. Firstly, the studies related to the mechanical and thermal properties of typical materials used in shipbuilding are outlined. Secondly, a brief introduction to the heat transfer analysis, Finite Element modelling and thermal stresses is provided. Finally, the review of papers dealing with the structural...
-
Modelling of Ship’s Heeling and Rolling for the Purpose of Gantry Control Improvement in the Course of Cargo Handling Operations in Sea Ports
PublicationThe paper presents two proposals of models of interaction between a ship and cargo being loaded or discharged by a gantry in port, in terms of heeling and rolling of the vessel. The main purpose of such modelling is the need for improvement of gantry control with regard to faster operations thanks to more accurate estimation of level and moment of cargo release from a gantry hook or spreader. The study may be the contribution to...
-
A hybrid model of flooding of the ro-ro ships in damaged conditions
PublicationThe paper presents some results on investigations concerning development of a hybrid model for assessment of performance of the ro‐ro ships in damaged conditions. The model is devoted towards assessing the performance of the damaged ro‐ro ships at the preliminary stage of design. The key problems associated with preparing of such the model are associated with working out a method of assessment of the damaged roro ships performance,...
-
Waterjet propulsion of small-draught inland waterways ships
PublicationPrzedstawiono aspekty napędu strugowodnego z punktu widzenia jego zastosowania na statkach żeglugi śródlądowej, zarówno zalety jak i wady (ograniczenia). Oceniono możliwości takiego zastosowania napędu strugowodnego.
-
Preliminary analysis of diesel electric ships propulsion solution
PublicationArtykuł zawiera opis wytwarzania i transmisji mocy układów disel-elektrycznych. Referat zwraca uwagę na problemy dotyczące zastosowania tych układów na statkach oraz pokazuje rozwój napędów disel-elektrycznych w ostatnim czasie.
-
A Model of Risk for Assessment of Safety of Ships in Damaged Conditions
Publication -
Stability criteria as constraints in a fleet of ships optimisation problem
PublicationRozwiązano problem dotyczący matematycznej optymalizacji floty statków wielozadaniowych typu rzeka-morze, przeznaczonych dla europejskiej żeglugi przybrzeżnej i eksploatowanych w obszarze Mórz Północnego i Bałtyckiego, na poziomie zadania transportowego za pomocą metod programowania nieliniowego z ograniczeniami. Zaproponowano metodę włączenia istniejących kryteriów skuteczności statków jako ograniczeń w ogólnym modelu optymalizacji...
-
Ships Shore Service Optimization Using the Queueing Theory
Publication -
Review of Autonomous and Remotely Controlled Ships in Maritime Sector
Publication -
The application of ultrafiltration for treatment of ships generated oily wastewater
Publication -
APPLICATION OF QUANTITATIVE RISK ASSESSMENT TO SHIPS IN EMERGENCY CONDITIONS
PublicationThe paper is devoted to safety of ships in emergency conditions. The currently valid prescriptive method of safety assessment of ships in damage conditions is included in the SOLAS 2009 Part B-2 Ch.II-1 regulations. It is devoted to the design stage and difficult to apply in operation. A possible alternative described in this paper is a method based on assessment of performance of ships and risk assessment. Type of risk evaluation...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublicationIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
A decision-making system supporting selection of commanded outputs for a ship's propulsion system with a controllable pitch propeller
PublicationThe ship's operators have to make decisions regarding the values of commanded outputs (commanded engine speed and pitch ratio) which ensure maximum vessel speed and minimum fuel consumption. Obviously, the presented decision problems are opposed. Therefore, there is a need for a compromise solution that enables more flexible vessel voyage planning. This paper deals with development of a computer-aided system supporting selection...
-
Effect of crystallization process at cryogenic conditions on the functional properties of the SUPERSTON alloy used in production the ship's propellers
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the SUPERSTON alloy used for ship's propellers. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. During the laser remelting at cryogenic conditions the microstructure changes significantly. This is related to synergistic effects of the solidification rate, phase transformations...
-
Application of the IMO standard manoeuvres procedure for pod-driven ships
PublicationInternational Maritime Organisation (IMO) in the resolution MSC.137(76) Standards for Ship manoeuvrability presents the manoeuvring criteria that has to be satisfied by majority of seagoing ships. Together with the criteria, procedures for carrying out the manoeuvring tests are also presented. They however do not correspond directly to ships with non-conventional steering-propulsion devices, like pod drives. IMO is aware of this...
-
An innovative method of measuring the extension of the piston rod in hydraulic cylinders, especially large ones used in the shipbuilding and offshore industry
PublicationThe article presents the results of selected works related to the wider subject of research conducted at the Faculty of Mechanical Engineering and Shipbuilding at the Gdańsk University of Technology, regarding designing various on board devices with hydraulic drive for ships and other offshore facilities. One of the commonly used these mechanisms are hydraulic actuators with the measurement of the piston rod extension. The issue...
-
Technological solutions for boosting hydrogen role in decarbonization strategies and net-zero goals of world shipping: Challenges and perspectives
PublicationFacing the problems concerning greenhouse gas (GHG) emissions from international ocean shipping has meant that the latest regulations of the International Maritime Organization, issued on 1st January 2023, have come into force, with the aim of reducing GHG emissions from maritime activities. Hydrogen has been suggested as an alternative fuel to achieve decarbonization ambitions in the near future. Although hydrogen has been investigated...
-
Improvement of ships seakeeping performance by application of the full-scale cfd simulations
PublicationThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflect very difficult operational conditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft, B-bow...
-
Towards a method for detecting large roll motions suitable for oceangoing ships
PublicationThe concept of autonomous merchant ships is quite recent. The increasing interest in autonomous vessels is nowadays calling for smart technologies that are supposed to replace the human actions on board. This involves troublesome issues related to ship safety. In the future, decision-making processes that are conventionally performed by human beings on board ship will be moved ashore to the control centre and maybe even completely...
-
Application of advanced CFD simulations in seakeeping analysis of ships (case study)
PublicationThe novel design process of many types of ships needs estimation of seakeeping properties. Especially ships like Offshore Supply Vessels, Wind Farm Support Vessels, Research Vessels, ferries, military vessels, rescue vessels require extended analysis of ship behavior on rough sea. The main reason for improving ships operability in different sea conditions is need of rising efficiency of propulsion system, reducing hull added resistance,...
-
Power efficient thrust allocation algorithms in design of dynamically positioned ships
PublicationAssessment of power consumption on a Dynamically Positioned (DP) ship in the early design stage can assist crucial design choices. The study presents a comparison between two algorithms of optimal thrust allocation in a propulsion system for an over-actuated DP ship. Applied algorithms were Quadratic Programming (QP) and Non- dominated Sorting Genetic Algorithm II (NSGAII). Based on both approaches, tools were developed for ship...
-
A method for assessing hazards, risks and safety of damaged ships at sea
PublicationPrzedstawiono wybrane problemy związane z metodą oceny bezpieczeństwa statków, opartej na ocenie zachowania się statku i ocenie ryzyka, w warunkach eksploatacyjnych. Omówiono zakres oceny bezpieczeństwa i analizy ryzyka w odniesieniu do zagadnienia zachowania się statku uszkodzonego na morzu. Analiza ryzyka oparta jest na zastosowaniu elementów Formalnej Oceny Bezpieczeństwa FSA. Opisano główne kroki analizy ryzyka. Podano podstawowe...
-
Investigation of the underwater noise produced by ships by means of intensity method
Publication -
A performance-oriented risk-based method for safety assessment of ships
PublicationW pracy przedstawiono wybrane informacje na temat metody oceny bezpieczeństwa statków w warunkach krytycznych. Metoda łączy podejście oparte na ocenie osiągów statku z podejściem opartym o ocenę ryzyka wypadku. Analiza ryzyka w metodzie oparta jest na zastosowaniu elementów Formalnej Oceny Bezpieczeństwa FSA. Analiza ryzyka w metodzie dotyczy: identyfikacji zagrożeń, oceny zagrożeń, identyfikacji scenariuszy wypadku, oceny ryzyka,...
-
Hydroacoustic ships berthing aid systems in Gdańsk north harbour
PublicationManewry dobijania statków do nabrzeży portowych są trudnymi operacjami, przy których należy uwzględniać m. in. na pływy, wiatry, widzialność, prędkość, masę statku, odległość od pirsu. Ewentualna kolizja z pirsem niesie poważne konsekwencje, szczególnie groźne dla wielkich statków a zwłaszcza tankowców. Referat prezentuje hydroakustyczne systemy kontroli manewrów statków wykonane przez zespół pracowników Katedry Systemów Elektroniki...
-
Influence of pitting corrosion on strength of steel ships and offshore structures
PublicationPraca dotyczy wpływu korozji wżerowej na własności mechaniczne stali o zwykłej i podwyższonej wytrzymałości oraz na wytrzymałość stalowych konstrukcji przy obciążeniach statycznych i quasi- statycznych. Artykuł oparty jest głównie na japońskich publikacjach. W próbie rozciągania, korozja wżerowa obniża nieznacznie obciążenie odpowiadające granicy plastyczności Re(nieznacznie) i wytrzymałości na rozciąganie Rm (silniej, redukuje...
-
Hydrodynamic aspects of unconventional propulsor design for small fast ships.
PublicationArtykuł przedstawia przegląd niekonwencjonalnych pędników dla małych, szybkich okrętów. Przegląd ten obejmuje pędniki strugowodne, śruby superkawitacyjne, śruby częściowo zanurzone oraz śruby kawitujące. Charakterystyczne cechy hydrodynamiczne tych pędników wymieniono i przedyskutowano, ze wskazaniem wad i zalet. Pokrótce przedstawiono dostępne metody projektowania i przedyskutowano ich oczekiwaną dokładność. Przegląd zilustrowano...
-
Automatic control systems for ships fitted with podded propulsion drive (POD).
PublicationW artykule ukazano celowość i możliwości automatyzacji układów napędowych, zwłaszcza typu POD, przewidzianych do zastosowania na projektowanych w ramach projektu Eureka BALTECOLOGICAL SHIP czterech statkach bałtyckich: kontenerowca, pojazdowa i tankowca oraz statku rzeczno - morskiego. Zawarte w artykule informacje ułatwiają dokonanie wyboru właściwych założeń projektowanego układu sterowania napędem wymienionych wyżej statków.
-
Potential and Use of the Googlenet Ann for the Purposes of Inland Water Ships Classification
PublicationThis article presents an analysis of the possibilities of using the pre-degraded GoogLeNet artificial neural network to classify inland vessels. Inland water authorities monitor the intensity of the vessels via CCTV. Such classification seems to be an improvement in their statutory tasks. The automatic classification of the inland vessels from video recording is a one of the main objectives of the Automatic Ship Recognition and...
-
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublicationModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...
-
A model of occurrence of the situations endangering inland waterways passanger ships and the environment
PublicationZaproponowano czterostanowy semimarkowski model pojawiania się sytuacji zagrażających pasażerskim statkom śródlądowym. Model ten został opracowany w formie semimarkowskiego procesu dyskretnego w stanach i ciągłego w czasie, którego wartościami są rodzaje stanów, interpretowanych jako sytuacje: normalna, skomplikowana, niebezpieczna oraz awaryjna. Zobrazowano przykładową realizację procesu zmian sytuacji, jakie mogą pojawić się...
-
Stochastic model of the load spectrum for main engines of sea-going ships
PublicationW artykule przedstawiono możliwość zastosowania procesów semimarkowskich do probabilistycznego opisu widma obciążeń silników o zapłonie samoczynnym, zastosowanych do napędu statków - czyli silników głównych. W rozważaniach uwzględnione zostały charakterystyki zewnętrzne mocy tego rodzaju silników. Umożliwiły one sformułowanie czteroelementowego zbioru stanów procesu obciążeń tego rodzaju silników. Do opisu rzeczywistego procesu...