Search
Filters
total: 478
filtered: 391
-
Catalog
Chosen catalog filters
Search results for: OPERATING CONDITIONS
-
Inspection of rubber linings operating in flue gas desulphurisation units
Publication -
FAILURE OF MAGNETIC FLUID SEALS OPERATING IN WATER: PRELIMINARY CONCLUSIONS
PublicationThe article analyses properties of magnetic fluid seals installed in rotary sealing no des which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals expo sed to long - term utility water loads, at different water pressures and shaft revolutions....
-
Influence of the operating frequency on DC-DC converters for HVDC grids
Publication -
Performance of vibration surveillance in order to improve operating parameters of manipulators
PublicationPrzedstawiono nadzorowanie drgań układu nośnego manipulatora robota IRb-6. Do nadzorowania drgań zastosowano algorytm sterowania modalnego przy energetycznym wskaźniku jakości. Celem proponowanego algorytmu jest minimalizacja poziomu drgań końcówek manipulatora, i tym samym - zwiększenie możliwości nowoczesnych linii zrobotyzowanych, jak również dokładności i powtarzalności pozycjonowania robota.
-
Chapter 8 : Possibilities of operating fuel consumption estimation of vehicles
PublicationPrzedstawiona w pracy metoda umożliwia ocenę eksploatacyjnego zużycia paliwa pojazdu samochodowego dzięki porównaniu zarejestrowanego zużycia paliwa z referencyjnym dla tych samych warunków eksploatacji. Warunki te mogą wynikać zarówno z lokalnej specyfiki ruchu pojazdów jak również ze sposobu prowadzenia auta przez kierowcę. Zgodnie z przyjętą metodą warunki te mogą zostać w bardzo prosty sposób zarejestrowane w czasie codziennej...
-
Experimental investigations of DAC Systems operating in VAV Control mode
PublicationPraca przedstawia techniczne aspekty wykorzystania ciepła sieciowego w bezsprężarkowych, adsorpcyjnych systemach klimatyzacyjnych na przykładzie zrealizowanej instalacji w EC Gdansk.Zaprezentowano również stanowisko oraz wyniki badań eksperymentalnych doyczących wpływu zmian parametrów przepływowych powietrza wilgotnego na efektywność pracy regeneratorów ciepła.
-
Numerical Simulation of Operating Parameters of the Ground Source Heat Pump
Publication -
Design and numerical study of turbines operating with MDM as working fluid
Publication -
Audio-visual surveillance system for application in bank operating room
PublicationAn audio-visual surveillance system able to detect, classify and to localize acoustic events in a bank operating room is presented. Algorithms for detection and classification of abnormal acoustic events, such as screams or gunshots are introduced. Two types of detectors are employed to detect impulsive sounds and vocal activity. A Support Vector Machine (SVM) classifier is used to discern between the different classes of acoustic...
-
Modelling of sequencing batch reactor operating at various aeration modes
PublicationThe presented study involved designing a computer model of a sequencing batch reactor (SBR) at laboratory scale. The data pertaining to the technical aspects of the bioreactor and quality indicators of wastewater constituted the input for the employed simulation tool, i.e. GPS-X software package. The results of a simulation involving a 12-hour operation cycle are presented in this work; each cycle included 6 phases: filling, mixing,...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublicationSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Shallow-Water Acoustic Communications in Strong Multipath Propagation Conditions
PublicationA phenomenon that has a strong impact on signal transmission conditions in Underwater Acoustic Communication (UAC) systems is multipath propagation. As a result of multipath propagation, the transmitted signal undergoes time dispersion which results in inter-symbol interference observed on the receiving side. Time dispersion is large, especially in horizontal channels in shallow waters which significantly limits the transmission...
-
Identification and non-integer order modelling of synchronous machines operating as generator
PublicationThis paper presents an original mathematical model of a synchronous generator using derivatives of fractional order. In contrast to classical models composed of a large number of R-L ladders, it comprises half-order impedances, which enable the accurate description of the electromagnetic induction phenomena in a wide frequency range, while minimizing the order and number of model parameters. The proposed model takes into account...
-
Problems in designing and operating the functional safety solutions of higher integriity levels
PublicationThe aim of this article is to identify and discuss some problems that have been encountered in designing and operating the functional safety solutions of higher safety integrity levels (SIL 3 and SIL 4) in the light of analyses outlined in a new version of the international standard IEC 61508:2010. Examples of such solutions are the electric / electronic / programmable electronic systems (E/E/PESs) and the safety instrumented systems...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublicationA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
Processing of acoustical data in a multimodal bank operating room surveillance system
PublicationAn automatic surveillance system capable of detecting, classifying and localizing acoustic events in a bank operating room is presented. Algorithms for detection and classification of abnormal acoustic events, such as screams or gunshots are introduced. Two types of detectors are employed to detect impulsive sounds and vocal activity. A Support Vector Machine (SVM) classifier is used to discern between the different classes of...
-
Comparative analysis of earthships and conventional buildings in terms of investment and operating costs
PublicationThe aim of the master's thesis is to present the idea of earthships and compare them with conventional buildings in terms of investment and operating costs. Earthships are buildings erected from tires and other wastes whose characteristic feature is their self-sufficiency. The first part of the master's thesis is to discuss the basic issues related to the earthship building. The beginnings of tire homes and their development are...
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublicationThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publicationequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublicationBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Advantageous conditions of saccharification of lignocellulosic biomass for biofuels generation via fermentation processes
PublicationProcessing of lignocellulosic biomass includes four major unit operations: pre-treatment, hydrolysis, fermentation and product purifcation prior to biofuel generation via anaerobic digestion. The microorganisms involved in the fermentation metabolize only simple molecules, i.e., monosugars which can be obtained by carrying out the degradation of complex polymers, the main component of lignocellulosic biomass. The object of this...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublicationThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
An optimization approach to coexistence of Bluetooth and Wi-Fi networks operating in ISM environment
PublicationW artykule rozważono problem wzajemnych interferencji pomiedzy urządzeniami standardów IEEE 802.11b oraz Bluetooth (BT). Zaproponowano model optymalizacyjny bazujący na podejściu programowania liniowego. Uzyskano znaczącą porawę wykorzystania pasma ISM w przypadku koegzystencji sieci rozważanych standardów.
-
Measurement of the earth fault loop impedance in a low voltage network with operating loads
PublicationW artykule przedstawiono problematykę dokładności pomiaru impedancji pętli zwarciowej w sieciach z obciążeniami roboczymi. Klasyczne metody pomiarowe i mierniki mogą powodować błędy pomiaru przekraczające dopuszczalną wartość. Z tego powodu może wystąpić ryzyko porażenia prądem elektrycznym, ponieważ przy doziemieniu nie będzie spełniony warunek samoczynnego wyłączenia zasilania. Błędy pomiaru w sieci z obciążeniami roboczymi można...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublicationIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
a rule for vibration surveillance of manipulators in order to improve operating parameters of industrial robots
PublicationPrzedmiotem rozważań są drgania układu nośnego manipulatora IRb-6. Proponowane podejście ma na celu minimalizację poziomu drgań końcówki manipulatora. Dla niestacjonarnego układu sterowanego, którego zachowanie opisano we współrzędnych uogólnionych, zdefiniowano energetyczny wskaźnik jakości uwzględniający energię kinetyczną i potencjalną układu, a także - chwilową energię sygnału sterującego. Dalsze rozważania dotyczą tymczasowego...
-
A XAS study of a highly diluted Pt electrocatalyst operating in PEM fuel cells
PublicationWe present an X-ray absorption spectroscopy (XAS) study of a low Pt content catalyst layer(Pt loading 0.1 mg c2) operating at the cathode of a proton exchange membrane fuel cell(PEMFC). This catalyst is based on the use of a mesoporous inorganic matrix as a support forthe catalyst Pt nanoparticles. Due to the high Pt dilution, in situ measurements of itsstructural properties by XAS are challenging and suitable experimental strategies...
-
Reliability and Operating Analysis of Transmission of Alarm Signals of Distributed Fire Signaling System
Publication -
The Issue of Operating Security Systems in Terms of the Impact of Electromagnetic Interference Generated Unintentionally
Publication -
Galvanic isolation circuit for measuring systems operating in environments with strong electromagnetic disturbances
Publication -
Operating system security by integrity checking and recovery using write-protected storage
PublicationThe paper presents an Integrity Checking and Recovery (ICAR) system which protects file system integrity and automatically restores modified files. The system enables files cryptographic hashes generation and verification, as well as configuration of security constraints. All of the crucial data, including ICAR system binaries, file backups and hashes database are stored in a physically write protected storage to eliminate the...
-
Polish DGPS System: 1995-2018 – Studies of Reference Station Operating Zones
Publication -
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
The excitation controller with gain scheduling mechanism for synchronous generator control
PublicationThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublicationThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Modeling sequencing batch reactor operational conditions depending on oxygen concentration
PublicationSequencing batch reactors (SBR) can be used as a fill-and draw activated sludge system for wastewater treatment with considerable operating flexibility and the possibility to conduct experiments under standard conditions and extreme case scenarios. Mathematical modeling and computer simulations provide an opportunity to implement existing wastewater processes in modeling software and evaluate different modifications at low costs...
-
Selected Issues of Hybrid Outboard Motors
PublicationThe aim of the research reported in the article was designing a hybrid drive system based on an outboard internal combustion engine offered by a selected producer and testing its operating characteristics. The article presents different designs of this type of drive which can be found in the literature and are available in the market. The designed hybrid outboard drive system was tested both on the laboratory test rig and in real...
-
Assessment of the Resistance Value of Trash Racks at a Small Hydropower Plant Operating at Low Temperature
Publication -
1.2V low-power four-quadrant CMOS transconductance multiplier operating in saturation region.
PublicationW pracy opisano niskomocową strukturę układową liniowego transkonduktancyjnego mnożnika czteroćwiartkowego pracującego w zakresie nasycenia. Układ analizowano z uwzględnieniem standardowego 0,35-mikrometrowego procesu CMOS. Przeprowadzone symulacje przy pomocy programu SPICE wykazały wysoką liniowość w odniesieniu do obu wejść sterujących X, Y. Np. dla sygnału harmonicznego 1 MHz; 0,3Vp-p na wejściu Y uzyskano zniekształcenia...
-
Semi-Markow Processes as Models of Devices´ Operating Process of Ship Pro-pulsion System
PublicationReferat zawiera formalny opis procesu eksploatacji urządzeń.
-
The modal control vibration surveillance of manipulators as a mean of improving operating parameters of industrial robots.
PublicationNowe zastosowania robotów, a przede wszystkim - operacje szybkiego montażu, technika kosmiczna oraz operacje manipulacyjne dużymi masami (niekiedy przekraczającymi masę własną manipulatora), stawiają przed robotami coraz to większe wymagania dotyczące m.in. dużej dokładności i powtarzalności pozycjonowania. Spełnienie powyższych wymagań, bez redukcji poziomu drgań występujących w układzie nośnym manipulatora, jest trudne do uzyskania....
-
High power, zero ripples active filtering system with power modules operating in parallel
Publication -
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part I)
PublicationW artykule przestawnie są problemy rozruchu i działania zespołów i układów hydraulicznych w niskich temperaturach otoczenia. Z tych powodów autor przebadał hydrauliczne zespoły i układy w warunkach szoku termicznego (oziębione zespoły zasilano gorącym czynnikiem roboczym). Określono parametry rozruchu w tych warunkach kilku zespołów oraz układów hydraulicznych, przy których ich eksploatacja jest bezpieczna. Badania eksperymentalne...
-
Effect of Hybrid Modulation on Performance of Wireless Battery Charger Operating in CC/CV Mode
Publication -
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part II)
PublicationPodczas rozruchu zespołów hydraulicznych w warunkach szoku termicznego dochodzi do dynamicznej zmiany wymiarów elementów tych zespołów. Odkształcenia elementów powodują zmianę efektywnego luzu między współpracującymi elementami. Na zmiany luzu ma pływ między innymi: różnica temperatur pomiędzy gorącym olejem a zimnym zespołem hydraulicznym, natężeniem przepływu czynnika roboczego, konstrukcji zespołu, rodzaju materiału i kształtu...
-
Reliability and operating properties of the electronic safety system used for unintended electromagnetic radiation sources
Publication -
Investigation of catalytic layers on anode for solid oxide fuel cells operating with synthetic biogas
PublicationIn this paper solid oxide fuel cells operating with dry synthetic biogas have been examined. In order to increase their stability the layers of CuO-CeO2, Cu1.3Mn1.7O4 and Y0.08Sr0.92Ti0.8Fe0.2O3 -δ have been deposited on the Ni-YSZ anode site. These layers should catalyze the internal biogas reforming and prevent the carbon deposition on the anode site. It has been found that CuO-CeO2 and Cu1.3Mn1.7O4 catalysts led to an increase...