Filters
total: 439
filtered: 377
-
Catalog
Chosen catalog filters
Search results for: MATERIAL PARAMETERS
-
Material Parameters Identification of Historic Lighthouse Based on Operational Modal Analysis
PublicationIn the present paper, the identification of the material parameters of a masonry lighthouse is discussed. A fully non-invasive method was selected, in which the material properties were determined via numerical model validation applied to the first pair of natural frequencies and their related mode shapes, determined experimentally. The exact structural model was built by means of the finite element method. To obtain experimental...
-
Methods of material parameters identification for isotropic damage in viscoplastic flow conditions
PublicationW pracy zaprezentowano trzy metody identyfikacji parametrów materiałowych dla izotropowego zniszczenia w warunkach lepkoplastycznego płynięcia. Przedstawiono wyniki identyfikacji dla dwóch stopów aluminium, które następnie zweryfikowano porównując wyniki symulacji numerycznych z wynikami eksperymentalnymi.
-
Rapid redesign of multiband antennas with respect to operating conditions and material parameters of substrate
PublicationThis work addresses geometry parameter scaling of multi-band antennas for Internet of Things applications. The presented approach is comprehensive and permits re-design of the structure with respect to both the operating frequencies and material parameters of the dielectric substrate. A two-step procedure is developed with the initial design obtained from an inverse surrogate model constructed using a set of appropriately prepared...
-
Identification and validation of material parameters for isotropic damage model in viscoplastic flow conditions
PublicationW pracy przedstawiono trzy różne sposóby identyfikacji parametrów materiałowych dla izotropowego modelu zniszczenia w warunkach płynięcia lepkoplastycznego. W celu ustalenia który sposób daje najlepsze rezultaty przeprowadzono każdą z identyfikacji dla wybranego materiału, a następnie dokonano ich oceny porównując wyniki symulacji numerycznych z wynikami eksperymentów. W pracy pokazano również praktyczne zastosowanie modelu - przykład...
-
Influence of material properties of charge on electrical parameters of induction heating setup
Publication -
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublicationThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublicationThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Possibilities of Production of New Reference Material ? Preparation of Gaseous Standard Mixtures Using Thermal Decomposition of Immobilized Compounds ? the Effect of Selected Parameters on the Amount of Released Analyte
Publication -
Possibilities of production of new reference material - preparation of gaseous standard mixtures using thermal decomposition of immobilized compounds - the effect of selected parameters on the amount of released analyte.
PublicationW pracy opisano wyniki badań dotyczących wytwarzania nowego typu bezmatrycowych materiałów odniesienia lotnych związków organicznych. Do otrzymywania lotnych analitów wykorzystano technikę termicznego rozkładu związków powierzchniowych. Badano wpływ parametrów prowadzenia reakcji modyfikacji i termicznego rozkładu otrzymanych związków powierzchniowych na ilość otrzymanego analitu. Wyznaczono powtarzalność i oszacowano niepewność...
-
THE INFLUENCE OF PET MECHANICAL PROPERTIES ON SBM PROCESS PARAMETERS – LITERATURE REVIEW
PublicationIn the paper it is said about the influence of PET (polyethylene terephthalate) mechanical properties on SBM (stretch blow molding) process output parameters changes. The below paper mentions also about the influence of PET orientation and crystallization processes on mechanical and thermal properties of PET material during SBM process. All mechanical data of PET material and SBM process output parameters changes are from collected...
-
Application of spectroscopy to the measurement of blood parameters
PublicationSpectroscopy is the study of formation and interpretation of the spectra arising from the interactions of all types of radiation on matter, understood as a collection of atoms and molecules. This is a very important department of optics which gives us many opportunities to measure various parameters such as material blood parameters. Among the diseases that are associated significantly with changes in rheological properties of...
-
Experimentation, material modelling and simulation of bonded joints with a flexible adhesive
PublicationThe paper deals with material parameters identification of a flexible adhesive and the numerical simulation of its behaviour in a single lap bonded joint. The material modelling was based on the simple shear and tensile-shear laboratory tests of the bonded joints made of thin aluminium and polyurethane plates with the flexible adhesive Terostat MS 9360 manufactured by Henkel AG & Co. The adhesive was considered as a hyperelastic...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublicationThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Material Identification of the Human Abdominal Wall Based On the Isogeometric Shell Model
PublicationThe human abdominal wall is an object of interest to the research community in the context of ventral hernia repair. Computer models require a priori knowledge of constitutive parameters in order to establish its mechanical response. In this work, the Finite Element Model Updating (FEMU) method is used to identify an heterogeneous shear modulus distribution for a human abdominal wall model, which is based on nonlinear isogeometric...
-
Elastoplastic material law in 6-parameter nonlinear shell theory
PublicationWe develop the elastoplastic constitutive relations for nonlinear exact 6-parameter shell theory. A J2-type theory with strain hardening is formulated that takes into account asymmetric membrane strain measures. The incremental equations are solved using implicit Euler scheme with closest point projection algorithm. The presented test example shows the correctness of the proposed approach. Influence of micropolar material parameters...
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublicationLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Influence of service ageing on polyester-reinforced polyvinyl chloride-coated fabrics reported through mathematical material models
PublicationIn this paper the coupled service (constructional tension) and environmental (sunlight, rainfalls, temperature variations) ageing influence on the polyester-reinforced polyvinyl chloride (PVC)-coated fabric VALMEX is studied. Two cases of the same fabric have been analyzed: one USED for 20 years on the real construction of the Forest Opera in Sopot (Poland), and one kept as a spare material (NOT USED). The following tests have...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublicationDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....