Filters
total: 2590
displaying 1000 best results Help
Search results for: ACTIVE MAGNETIC BEARINGS
-
Magnetic signatures of land vehicles
PublicationThe results of numerical simulations of the magnetic field surrounding of land vehicles' models have been presented in this paper. Vehicle containing of ferromagnetic elements distorts the Earth's magnetic field. This distortion can be measured by magnetometers. It is possible to detect and identify an object on the basis of its magnetic signature.
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Experimental investigation into surface texture effect on journal bearings performance
PublicationThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublicationThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Multidipoles model of ship's magnetic field
PublicationShips made of ferromagnetic metals interfere with Earth's magnetic field in their surrounding. The disturbance of the magnetic field makes possible localization and even identification of the ship, which could determine a threat to the ship. The measurement of the magnetic field around the ship enables to determine its magnetic signature. The paper presents a multidipoles model of the ship magnetic field, which allows to determine...
-
Multidipoles model of ship's magnetic field
PublicationShips made of ferromagnetic metals interfere with Earth's magnetic field in their surrounding. The disturbance of the magnetic field makes possible localization and even identification of the ship, which could determine a threat to the ship. The measurement of the magnetic field around the ship enables to determine its magnetic signature. The paper presents a multidipoles model of the ship magnetic field, which allows to determine...
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Enhancement of the Magnetic Coupling in Exfoliated CrCl 3 Crystals Observed by Low‐Temperature Magnetic Force Microscopy and X‐ray Magnetic Circular Dichroism
PublicationMagnetic crystals formed by 2D layers interacting by weak van der Waals forces are currently a hot research topic. When these crystals are thinned to nanometric size, they can manifest strikingly different magnetic behavior compared to the bulk form. This can be the result of, for example, quantum electronic confinement effects, the presence of defects, or pinning of the crystallographic structure in metastable phases induced by...
-
Isolation of the relative decrease in magnetic permeability contribution to reluctance of an open magnetic circuit based on stray field measurements
PublicationThe goal of the study was to evaluate a relative decrease in magnetic permeability in open magnetic circuits based on stray magnetic field measurements. The boundary element method was used to simulate magnetic circuits with variable geometry and variable magnetic permeability. The simulated magnetic circuits were rectangular or bone-shaped flat samples. Reluctance was increased in the middle of the samples resulting in leakage...
-
Magnetic properties of α-KCoPO4 compound with a chiral polar crystal structure
PublicationWe have obtained polycrystalline samples of a metastable α variant of KCoPO4 by low temperature (350–400 °C) solid state metathesis reaction of potassium oxalate and ammonium cobalt orthophosphate. The material crystallizes in a polar chiral structure (sg. P63, no. 173). Measurements of magnetic properties reveal antiferromagnetic interactions and no ordering observed down to T = 1.9 K, well below the Weiss temperature |Θcw| =...
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Novel condition monitoring of induction motor bearings via motor current signature analysis
PublicationThe paper authors are researching the assessment of bearing conditions in induction motors. The methods developed by the authors are based on measurements and analysis of the motor supply current, which is particularly attractive in the absence of access to the engine. The article provides an overview of selected methods of induction motor bearings diagnostic based on Motor Current Signature Analysis (MCSA). However, there is no...
-
The Dynamic Model of Magnetic Hysteresis
PublicationThis paper presents the scalar dynamic magnetic hysteresis model based on the Preisach theory. The important role in this theory played hysteresis operator states. The changes of these operators` states are not immediate in the dynamic model but they are a function of time and parameter k representing the magnetic properties of the material. In this paper the transient state of the hysteresis operator is defined by the nonlinear...
-
POSSIBILITY OF ASSESSMENT OF OPERATION OF SLIDING BEARINGS IN PISTON-CRANK MECHANISMS OF DIESEL ENGINES WITH REGARD TO LOAD AND TIME OF CORRECT WORK OF THE BEARINGS BY APPLYING ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationAbstract: The paper presents a possibility of determining (assessing) operation of sliding bearings with multilayer bushings in crank-piston mechanisms of diesel engines. Properties of load and wear, particularly fatigue and abrasive, are characterized in general. Acoustic emission as a diagnostic signal was proved to be useful for detection of the wear of sliding and barrier layers. Results of measurements of acoustic emission...
-
Anna Zielińska-Jurek dr hab. inż.
People2018 DSc in technical sciences in the field of chemical technology Chemical Faculty, Gdansk University of Technology, Title: “Functionalized titanium(IV) oxide as a photocatalyst for environmental purification” 2011 Ph. D. in technical sciences in the field of chemical technology Chemical Faculty, Gdansk University of Technology, Title of the dissertation:...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublicationWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
Magnetic Resonance
Journals -
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublicationJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Application of magnetic nanoparticles for magnetic solid-phase extraction in preparing biological, environmental and food samples
PublicationThe need to obtain meaningful results as the basis for determining the content of trace amounts of analytes has become the driving force behind the development of modern analytical techniques, including sample-preparation techniques, such as solid-phase extraction (SPE). Recently, great interest was aroused in the use of magnetic nanoparticles (MNPs) in SPE. These materials exhibit high selectivity, and, in small amounts, can provide...
-
Magnetic nanocomposites for biomedical applications
PublicationTissue engineering and regenerative medicine have solved numerous problems related to the repair and regeneration of damaged organs and tissues arising from aging, illnesses, and injuries. Nanotechnology has further aided tissue regeneration science and has provided outstanding opportunities to help disease diagnosis as well as treat damaged tissues. Based on the most recent findings, magnetic nanostructures (MNSs), in particular,...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
Research of leakage magnetic field in deenergized transformer
PublicationThe article deals with the issue of the numerical analysis of the magnetic field occurring around the transformer after it has been powered down. The main goal of this analysis was to examine if it is possible to identify the residual fluxes in the transformer legs based on this fields’ measurements. It was also intended to determine the type and the location of magnetic sensors. Numerical analysis of the magnetic field was performed....
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Analysis of magnetic field of Helmholtz's coils
PublicationThe 3-axis fluxgate magnetometer requires conducting a precise calibration in the magnetic field whose value is determined and which is characterized by the high uniformity of the distribution of the field, especially along the axis of the sensors. The generation of the magnetostatic field characterized by the high uniformity, can be achieved by using the Helmholtz's coils. The requirements of the uniformity of distribution of...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
TiO2-based magnetic nanocomposites with core-shell structure
PublicationThe main aim of the doctoral dissertation was preparation and characterization of photocatalysts, with particular emphasis on modified titanium (IV) oxide photocatalysts, which can be applied for the degradation of organic pollutants not susceptible to biodegradation. A particularly important aspect of the work was the development of preparation method of nanocomposites with the magnetic core-shell and photocatalyst shell (TiO2)...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Disturbances of magnetic field in surrounding of mobile, metalic plate
PublicationThe uniform magnetic field of the Earth in the surrounding of a mobile, metalic object undergoes deformation by eddy currents. The influence of the moving conducting object on total magnetic field of the Earth depends on the object's shape, position and speed of the changes relative to the magnetic field's vector of the Earth as well as the electric conductivity and the relative magnetic permeability of the material. The disturbances...
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublicationIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
-
Characterization of glucoamylase immobilized on magnetic nanoparticles
PublicationMagnetic support was prepared by precipitation from an alkaline solution of divalent and trivalent iron ions and subsequently was modified with 3-aminopropyltriethoxysilane. FTIR analysis showed existence of a new Si-O-Fe bond in obtained particles. Scanning electronic microscopy images shows that the nanoparticles of all samples have particle size below 30 nm. Glucoamylase AMG 300L was immobilized onto the modified magnetic support...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublicationThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Active Suppression of Nonstationary Narrowband Acoustic Disturbances
PublicationIn this chapter, a new approach to active narrowband noise control is presented. Narrowband acoustic noise may be generated, among others, by rotating parts of electro-mechanical devices, such as motors, turbines, compressors, or fans. Active noise control involves the generation of “antinoise”, i.e., the generation of a sound that has the same amplitude, but the opposite phase, as the unwanted noise, which causes them to interfere...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Active Dynamic Thermography in Medical Diagnostics
PublicationThis is an overview of active thermal imaging methods in medical diagnostics using external thermal stimulation. In this chapter, several clinical cases diagnosed using the active dynamic thermography method, ADT, are presented. Features of this technology are discussed and main advantages underlined. Applications in skin burn diagnostics and quantitative evaluation leading to modern classification of burned patients for further...
-
MAKING OF FERROMAGNETIC ELLIPTICAL SHELL IN TRANSVERSE MAGNETIC
PublicationA ferromagnetic object, located in the Earth’s magnetic field, changes its distribution. Through measuring such disturbances, one can locate the object and destroy it. To conceal the object, a special winding is placed inside its ferromagnetic shell, and its task is to eliminate the disturbances in the distribution of the Earth’s magnetic field.
-
NEW DESIGNS OF MAGNETIC FLUID SEALS FOR RECIPROCATING MOTION
PublicationT he operating conditions of magnetic fluid seals during reciprocating motion are so different from those observed in rotating motion that the use of their conventional structures for reciprocating motion seals yields no good results. The analysis of the sealing mechanism of magnetic fluid seals in reciprocating motion shows that the operation of these seals is affected by the carry-over phenomenon and magnetic fluid...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Low-Dimensional Magnetic Semimetal Cr0.65Al1.35Se3
PublicationWhile exploring novel magnetic semiconductors, the new phase Cr0.65Al1.35Se3 was discovered and characterized by both structural and physical properties. Cr0.65Al1.35Se3 was found to crystallize into orthorhombic CrGeTe3-type structure with space group Pnma (no. 62). Vacancies and mixed occupancies were tested, and the results show that one of the 4c sites accommodates a mixture of Cr and Al atoms, while the other 4c site is fully...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublicationWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Comparison of active proximity radars for the wearable devices
PublicationTwo methods of object position and movement estimation in relation to the user of smart glasses were investigated. An active infrared and ultrasonic methods of the obstacle detection were presented and compared. Application of these methods depend on active transducers type (physical medium used), geometry and surface properties of detected objects and their movement direction and speed. In the article properties of both detectors...
-
Is it possible to predict performance of large thrust bearings on the basis of the results of experiments on smaller bearings?
PublicationTreścią referatu jest analiza możliwości przeniesienia wyników badań modelowych z małych hydrodynamicznych łożysk wzdłużnych do określenia własności łożysk o dużych rozmiarach. Posłużono się analizą wymiarową do określenia wymaganych współczynników skali, których zachowanie podczas badania łożyska modelowego, zapewnia jego podobieństwo do łożyska o dużych rozmiarach. Uzyskane wyniki poddano dyskusji.
-
Finite-difference time-domain analyses of active cloaking for electrically-large objects
PublicationInvisibility cloaking devices constitute a unique and potentially disruptive technology, but only if they can work over broad bandwidths for electrically-large objects. So far, the only known scheme that allows for broadband scattering cancellation from an electrically-large object is based on an active implementation where electric and magnetic sources are deployed over a surface surrounding the object, but whose ‘switching on’...
-
Disturbances of Earth magnetic field caused by eddy currents of airplane
PublicationThe uniform magnetic field of the Earth in the surrounding of a mobile, metallic object undergoes deformation by eddy currents. The influence of the moving, conducting object on the Earth's total magnetic field depends on the object's shape, position and speed of the changes relative to the magnetic field vector of the Earth, as well as the electric conductivity and the relative magnetic permeability of the material. Disturbances...