Search results for: surface flow
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Analysis and interpretation of radiometric signals in a liquid-gas bubble flow
PublicationThe article presents the analysis of signals from a radiometric system consisting of two scintillation probes and two gamma radiation sealed sources. Calculations and interpretation were carried out for the bubble flow of the water-air mixture in the horizontal pipeline. The analysis of the obtained signals was done in time and frequency domain. In the frequency domain, a range of usable frequencies was identified, which were associated...
-
DISTRIBUTION OF FLOWS IN A CHANNEL NETWORK UNDER STEADY FLOW CONDITIONS
PublicationThe article presents an algorithm for calculating the distribution of flow in a junction of open channel network under steady flow conditions. The article presents a simplified calculation algorithm used to estimate the distribution of flow in a network of channels under steady flow conditions. The presented algorithm is based on the continuity equation and a simplified energy equation. To describe the relationship between the...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Hysteresis curves for some periodic and aperiodic perturbations in magnetosonic flow
PublicationA thermodynamic relation between perturbations of pressure and mass density in the magnetohydrodynamic flow is theoretically studied. Planar magnetohydrodynamic perturbations with the wave vector, which forms a constant angle with the equilibrium magnetic field, are under study. The theory considers thermal conduction of a plasma and the deviation from adiabaticity of a flow due to some kind of heating–cooling function. It also...
-
OBTAINING FLUID FLOW PATTERN FOR TURBINE STAGE WITH NEURAL MODEL.
PublicationIn the paper possibility of applying neural model to obtaining patterns of proper operation for fluid flow in turbine stage for fluid-flow diagnostics is discussed. Main differences between Computational Fluid Dynamics (CFD) solvers and neural model is given, also limitations and advantages of both are considered. Time of calculations of both methods was given, also possibilities of shortening that time with preserving the accuracy...
-
Reduction of Computational Complexity in Simulations of the Flow Process in Transmission Pipelines
PublicationThe paper addresses the problem of computational efficiency of the pipe-flow model used in leak detection and identification systems. Analysis of the model brings attention to its specific structure, where all matrices are sparse. With certain rearrangements, the model can be reduced to a set of equations with tridiagonal matrices. Such equations can be solved using the Thomas algorithm. This method provides almost the same values...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Elektrochemiczne magazyny energii - baterie przepływowe typu "redox flow"
PublicationRozwój i wzrost udziału energii odnawialnej, ze względu na kurczące się zasoby konwencjonalnych źródeł energii i ochronę środowiska, jest możliwy tylko dzięki współpracującym z nimi odpowiednim stacjonarnym magazynom energii. Technologia baterii przepływowych (ang. redox flow batteries, RFB) pozwala świetnie zaspokoić tego typu potrzeby ze względu na: (i) wyjątkowo dużą skalowalność układów; (ii) niezależny dobór mocy i pojemności...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublicationIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
PROPERTIES OF ONE DIMENSIONAL OPEN-CHANNEL STEADY FLOW EQUATIONS
PublicationIn this paper properties of discrete forms of one dimensional steady gradually varied flow equations are discussed. Such forms of flow equations are obtained as a result of approximation of their differential forms, which is required to solve them numerically. For such purpose explicit or implicit numerical approximation schemes for ordinary differential equations can be applied. It turns out that dependently on the chosen approximation...
-
Recent progress in experimental studies of electrohydrodynamic flow in electrostatic precipitators
PublicationMany experimental, theoretical and numerical works were devoted to the electrohydrodynamic (EHD) flow generated in electrostatic precipitators (EPSs). The generally accepted conclusion from these studies is that the EHD flow plays an important role in the particle collection in ESPs. However, despite of the recent fast progress in numerical simulation and experimental techniques used in the ESPs studies many problems related to...
-
Numerical Analysis of Flow in Building Arrangement: Computational Domain Discretization
Publication -
Modelling of energy flow in electrical machines. A bond graph approach
PublicationPrzedstawiono w ujęcia grafów wiązań model przepływu energii/mocy w maszynach elektrycznych pracujących w hybrydowych systemach przetwarzania energii. Jako przykład do rozważań przyjęto system napędu trakcyjnego pojazdów hybrydowych.
-
Application of vertical flow cw for highly contaminated wastewater treatment
PublicationBasing on quantitative and qualitative characteristics of reject waters generated during digested sewage sludge dewatering on centrifuges in conventional WWTP (RWC) and municipal landfill leachate (LL), the pilot constructed wetlands for treatment of both types of highly contaminated wastewater were designed. In the paper the characteristics of the pilot plants and assumed treatment efficiencies are presented. According to the...
-
Monitoring of solid behaviour during gravitational flow in rectangular silo
PublicationW pracy przedstawiono wyniki pomiarów zmian koncentracji w protokątnym modelu silosu. Omówiono przyczyny błędów pomiarowych w modelu protkątnym, zarówno dla danych surowych, jak rózniez danych zrekonstruowanych.
-
Analysis of latency between quotations and capital flow in capital markets.
PublicationThe aim of this paper is to prove that the derivative of the log of capital flow understood as price times volume advances the derivative of log of the price. A certain concept of signal processing using linear filtering has been proposed to conduct the research.
-
Approximate models and parameter analysis of the flow process in transmission pipelines
Publicationthe paper deals with the problem of early leak detection in transmission pipelines. First we present the derivation of state-space equations of the flow process in the pipelines. This description is then aggregated in order to obtain a principal model. Next, the problem of process model parameterization is addressed, taking into account the maximization of a model stability margin. The location of the maximum is determined using...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
On various modelling approaches to real-time visualisation of blood flow
PublicationThis paper reviews various modelling approaches to real-time visualisation of blood flow. These include classic, macroscale approach based on the momentum conservation equation together with a proper constitutive equation. Moreover, modern micro- and mesoscale approaches, such as molecular dynamics and dissipative particle dynamics, are discussed. Advantages and disadvantages of the discussed methods are highlighted with particular...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublicationThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Uncertainty of the liquid mass flow measurement using the orifice plate
PublicationThe article presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters. Not only the quantitative estimation but also the qualitative results of those measurements are important. To achieve these results the authors of the paper propose to use the theory of uncertainty. The article shows the analysis of the...
-
Cross-Flow Microfiltration of Glycerol Fermentation Broths with Citrobacter freundii
Publication -
Effect of flow-rate on ethanol separation in membrane distillation process
Publication -
Confined granular flow in silos with inserts - full-scale experiments
PublicationArtykuł omawia wyniki doświadczalne przepływów silosowych w silosach w naturalnej skali ze wstawkami. Podczas doświadczeń pomierzono przemieszczenia oraz napór na ściany. Zastosowano różne typy wstawek położone na różnej wysokości. Wyniki badań doświadczalnych porównano z przepływami bez wstawek.
-
Experimental and theoretical investigations of silo music during granular flow
PublicationPraca dotyczy analizy efektów dynamicznych w silosach podczas przeływu materiałów sypkich.
-
Numerical simulations of granular material flow in silos with and without insert
PublicationArtykuł omawia wyniki naporu materiału sypkiego podczas przepływu w silosach z i bez wkładek. Obliczenia wykonano wykorzystując sformułowanie ale na bazie prawa sprężysto-plastycznego według druckera-pragera. Zbadano wpływ kształtu i położenia wkładki na wielkość naporu i rodzaj przepływu.
-
Experimental and theoretical studies of resonance effects during silo flow.
PublicationPrzedstawiono badania nad rezonansowymi efektami dynamicznymi podczas przepływów silosowych. Wpływ rezonansu na wielkość naporu był analizowany przy pomocy badań doświadczalnych i obliczeń MES na bazie prawa mikropolarnego sprężysto-plastycznego. Doświadczenia wykonano w silosie o przekroju okrągłym i prostokątnym. Zaproponowano efektywną metodę redukcji efektów dynamicznych.
-
Numerical modeling of shear localizations during granular flow in silos.
PublicationW artykule przedstawiono wyniki numerycznej analizy MES dotyczącej przepływów materiałów sypkich w silosach. Omówiono różne metody opisu lokalizacji odkształceń stycznych wewnątrz materiałów. Wyniki porónano z wynikami doświadczalnymi.
-
Simulations of flow patterns in silos with a cellular automaton - part 2
PublicationW artykule przedstawiono wyniki symulacji przepływów silosowych przy zastosowaniu zaawansowanego aparatu komórkowego, w którym uwzględniono kolizje cząstek i dysypację energii. Obliczenia wykonano dla przepływu masowego i kominowego.
-
Influence of selected CO2 absorption promoters on the characteristics of calcium carbonate particles produced by carbonation of the post-distillation liquid from the Solvay process
PublicationThe aim of this work is to compare the effect of selected process parameters, gas flow rate, CO2 absorption promoter concentration and its pKa, on the precipitation of CaCO3 by the gas-liquid method using a model post-distillation liquid from the Solvay process. To ensure effective capture of CO2, the absorption promoters used were ammonia, triethanolamine and triethylamine. The Box-Behnken Design was applied to plan the experiments....
-
Insights Into Hydrodynamics of Spinning Fluids Reactor
PublicationSpinning fluids reactor (SFR) is one of the most efficient gas-liquid contacting system with high potential of application in many fields. The unique solution of SFR is the contacting of two spinning fluids which generated centrifugal force. The aim of this study was to investigate the pressure field distribution on the inner surface of reactors dispersing element. Obtained results confirm the high heterogeneity of the field pressure...
-
Multi-DBD actuator with floating interelectrode for aerodynamic control
PublicationIn this paper the use of a floating inter-electrode in a multi-DBD (dielectric barrier discharge) plasma actuator is described. The multi-DBD plasma actuators with floating inter-electrodes were investigated to get a longer DBD on a dielectric surface and to maximise generated net airflow. Our actuator was used to control the boundary layer flow separation around NACA0012 airfoil model. The results of our investigations suggests...
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublicationNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Multiple jets impingement – numerical analysis by the ζ-f and hybrid VLES turbulence models
PublicationPresented paper summarizes the Authors findings referring to the numerical analyses of the jet impinging phenomena in the case of complex jets configurations in various applications e.g. in the heat exchangers. Multiple jets interference resulting in the cross-flow and the surface curvature are the factors which impose the need of advanced turbulence models utilization. The outcome of the research based on the ζ-f turbulence model...
-
The Effect of Surface Treatment with Isocyanate and Aromatic Carbodiimide of Thermally Expanded Vermiculite Used as a Functional Filler for Polylactide-Based Composites
PublicationIn this work, thermally expanded vermiculite (TE-VMT) was surface modified and used as a filler for composites with a polylactide (PLA) matrix. Modification of vermiculite was realized by simultaneous ball milling with the presence of two PLA chain extenders, aromatic carbodiimide (KI), and 4,4’-methylenebis(phenyl isocyanate) (MDI). In addition to analyzing the particle size of the filler subjected to processing, the efficiency...
-
Reverse flow routing problem solved by the Space-Time Conservation Method
PublicationW artykule rozpatruje się zagadnienie odwrotnej transformacji przepływów dla przypadku przepływu nieustalonego wolno zmiennego w kanałach otwartych, opisanego układem równań de Saint Venanta. Przedstawiono specyficzne dla rozpatrywanego przypadku problemy powstające na etapie jego rozwiązywania oraz zaproponowano efektywny algorytm obliczeniowy, wykorzystujący nową, atrakcyjną metodę czasoprzestrzennych objętości skończonych. Do...
-
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
Turbulent flow and heat transfer of a liquid film formed by impinging jet.
PublicationZaproponowano prosty model wymiany ciepła w turbulentnym filmie cieczowym utworzonym przez uderzająca strugę. Rozpatrzono dwa przypadki: przepływ rozwijający się i w pełni rozwinięty filmu cieczowego. W obu przypadkach model wyprowadzono na podstawie zmiany grubości filmu w wyniku działania sił bezwładności i sił tarcia. Wyznaczono profile prędkości w obu zakresach co umożliwia wyznaczenie współczynników wymiany ciepła.
-
Physical modelling of water flow in 'Wild River' type water slide
PublicationPrzedstawiono wyniki fizycznego modelowania przepływu w zjeżdżalni wodnej typu Dzika Rzeka. Badania dotyczyły obiektu należącego do parku wodnego "Świat Wodny Nemo" w Sopocie. Eksperymenty przeprowadzono w Laboratorium Hydrauliki i Inżynierii Środowiska Politechniki Gdańskiej. Zaobserwowany w systemie kanałów i zbiorników przepływ wody można ocenić jako szybkozmienny. Wskutek zmian spadku dna kanałów oraz łuków trasy zjazdu obserwowano...
-
On thermal and Flow Expert Systems Based on Artificial Neural Network (ANN)
PublicationZaprezentowano możliwość realizacji jednego z zadań systemów eksperckich, polegającego na określaniu rozmiaru eksploatacyjnej degradacji parametrów geometrycznych układów łopatkowych turbin. Dyskusję przeprowadzono w oparciu o zastosowanie wybranego typu sztucznej sieci neuronowej (SSN). Badano jakość i dokładność polegającą na dobrej identyfikacji rozmiaru degradacji przez tę wybraną SSN wykrywającą rozmiar degradacji geometrycznej....
-
Hard and Soft Modelling Based Knowledge Capture for Information Flow Management
PublicationW rozdziale przedstawiono najpierw złożony aparat matematyczny który może być wykorzystany w modelowaniu zarządzania informacją i oceny jej wartości w procesach decyzyjnych. Aparat ten oparto na teorii procesów stochastycznych oraz na teorii uzyteczności. Następnie, opierając się na wypracowanym modelu matematycznym, zaproponowano przejście do modelowania miękkiego. Całość zilustrowano na przykładach z obszaru zarządzania informacją.
-
Flow cytometric analysis of reticulocyte maturation after erythropoietin administration in rats
Publication -
Optimal Power Flow Problem Using Particle Swarm Optimization Algorithm
Publication -
The use of liquid crystal thermography for heat, fluid flow and biomedical research.
PublicationW ostatniej dekadzie termografia ciekłokrystaliczna (TLC) i cyfrowa analiza kolorowych obrazów była z powodzeniem stosowana w różnych aplikacjach technicznych, przemysłowych i biomedycznych. Cienkie warstwy ciekłokrystaliczne zastosowano dla uzyskania lokalnych pól temperatury, współczynników przekazywania ciepła i określenia rodzaju procesu. Materiał ciekłokrystaliczny można również zastosować do wizualizacji pól temperatury i...
-
Performance of subsurface vertical flow constructed wetlands receiving municipal wastewater.
PublicationPrzedstawiono skuteczność pracy oczyszczalni hydrofitowych z pionowym przepływem ścieków. Wsazano jak usuwanie azotu uzależnione jest od temperatury, podobnie usuwanie ładunkuu BZT5. Wskazano na różnice w pracy oczyszczalni w okresie lata i zimy.