Filters
total: 6058
filtered: 4902
displaying 1000 best results Help
Search results for: pandemic threat
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublicationVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublicationW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Numerical modeling of cross-flow heat exchanger for air-conditioning purposes in preliminary study.
PublicationPraca przedstawia wyniki obliczeń numerycznych krzyżowego płytowo-rurowego wymiennika ciepła przeznaczonego do celów klimatyzacyjnych w początkowym etapie jego projektowania.
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublicationThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublicationAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
AUGMENTATION OF THE CRITICAL HEAT FLUX IN WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublicationThe main aim of the proposed study is therefore recognition of the phenomena accompanying nucleate boiling crisis of selected nanofluids during boiling on horizontal tubes of various outside diameters. Of particular interest is impact of contact angle and tube diameter on the value of critical heat flux. The results obtained should give more light on the nature of nucleate boiling crisis and will serve as a basis for future theoretical...
-
Modifications of the heat source model in numerical analyses of the metal-cored arc welding process
Publication -
EFFECT OF WORKING FLUID SELECTION ON THERMAL PERFORMANCE OF HEAT EXCHANGER FILLED BY THE POROUS MATERIAL
PublicationThermal management of electronics semiconductor technologies that are located i.e. in a novel marine power plants or computer server rooms become very important issue for designers of such systems. Motivation and need for research in development of novel cooling strategies for modern electronics is of paramount importance. Heat exchangers filled by the porous material are a novel research topic in current heat pipe science. The...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Modelling of two-component turbulent mass and heat transfer in air-fed pressurised suits
PublicationIn this paper the modelling of an important industrial problem is addressed, which involves the two-component turbulent flow with heat transfer that takes place inside protective clothing. The geometry of the flow boundaries is reconstructed in a CAD system from photogrammetry scan data. The overall model is sufficiently realistic to allow, after validation, design improvements to be tested. Those presented here allow the reduction...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublicationThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublicationThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Implementation of the Boundary Element Method to Two-Dimensional Heat Transfer with Thermal Bridge Effects
PublicationThe work presents an application of the boundary element method applied to a two-dimensional conductive heat transfer. The algorithm of the method is explained and its advantages are outlined. Green's function as a fundamental solution for Poisson's equation in two dimensions was used and the direct approach was applied. The presented results concern building construction elements as typical cases of thermal bridges. Some properties...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publicationmodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Natural convective heat transfer from isothermal horizontal, vertical and inclined plates - a review
PublicationW artykule przedstawiono przegląd otrzymanych przez różnych badaczy korelacji eksperymentalych, teoretycznych i numerycznych, opisujących wymianę ciepła od izotermicznych płyt o różnym kącie pochylenia. Przedstawiono model matematyczny zjawiska. Opisano stosowane metody badawcze i wskazano przyczyny rozbieżności pomiędzy przedstawionymi przez wielu autorów wynikami.
-
The use of liquid crystal thermography and particle image velocimetry in the exploration of heat transfer measurements
PublicationArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Application of mechanical Barkhausen noise in assessment of X20 steel properties after heat treatment
Publication -
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublicationW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublicationIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublicationThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublicationAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublicationThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Influence of Cement Replacement with Sewage Sludge Ash (SSA) on the Heat of Hydration of Cement Mortar
PublicationThe amount of fly ash from the incineration of sewage sludge is increasing all over the world, and its utilization is becoming a serious environmental problem. In the study, a type of sewage sludge ash (SSA) collected directly from the municipal sewage treatment plant was used. Five levels of cement replacement (2.5%, 5%, 7.5%, 10% and 20%) and unchanged water-to-binder (w/b) ratio (0.55) were used. The purpose of the study was...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublicationThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Two bacterial small heat shock proteins, IbpA and IbpB, form a functional heterodimer
PublicationSmall heat shock proteins (sHsps) are a conserved class of ATP-independent chaperones which in stress conditions bind to unfolded protein substrates and prevent their irreversible aggregation. Substrates trapped in sHsps-containing aggregates are efficiently refolded into native structures by ATP-dependent Hsp70 and Hsp100 chaperones. Most γ-proteobacteria possess a single sHsp (IbpA), while in a subset of Enterobacterales, as...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Importance of Specific Heat Characterization when Reporting New Superconductors: An Example of Superconductivity in LiGa2Rh
PublicationWe show that the full-Heusler compound LiGa2Rh is a superconductor with Tc = 2.4 K. The new superconductor was found as a result of an intuition-based extension of a database search for superconductors that looked for the presence of peaks in the electronic band structure near the Fermi energy. The measurement of the entropy loss during the transition from the nonsuperconducting to the superconducting state, a straightforward measurement...
-
Proposal of a mobile medical waste incinerator with automatic waste feeder and heat recovery system
PublicationThe paper presents and discusses the issue of medical waste (including hazardous ones) and their proper management. Inappropriate handling of infectious medical waste directly endangers the human being health and the environment. Infectious waste must therefore be properly disposed of – one of the most commonly used methods is the thermal treatment in the incinerators tailored for this purpose. During designing an incinerator unit,...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublicationConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
Influence of Heat Treatment Temperature on Fatigue Toughness in Medium-Carbon High-Strength Steels
PublicationCurrent research has demonstrated that the tempering temperature affects the martensitic transformation of medium-carbon high-strength steels. This temperature plays an important role in the final microstructure, percentage ratios of martensite to ferrite phases and, consequently, in the mechanical properties and the fatigue response. So far, the relationship between the martensitic tempering temperature and the cyclic deformation...
-
Effect of tube bundle arrangement on performance of shell-and-tube latent heat storage system
PublicationThis work presents the results of experimental investigation on charging and discharging of latent heat storage systems (LHSS) in the form of shell-and-tube heat exchangers with a variable arrays of the tube bundles. The tests included two tube arrangements – in-line and triangular (staggered), a variable number of tubes in a bundle, two pitch ratios, and different tube positions in a bundle. Three commercial products (LTP56, RT54HC,...
-
A New Critical Risk on the Block: Cyber Risks as an Example of Technical Knowledge Risks in Organizations
PublicationThe breakout of the COVID-19 pandemic has intensified the appearance of many additional technical knowledge risks in organizations. Cyber risks in particular are becoming a great challenge for organizations. At the same time, academic research on cyber risks, their costs, consequences and ability of overcoming them is still scarce and fragmented. In order to fill this gap, the paper is aimed to identify different types of cyber...
-
Changes in the structure of Armenia’s labour resources between 1993 and 2020
PublicationThe article characterises the structure of Armenia’s labour resources in the period between1993 and 2020. It aims to assess the changes on the Armenian labour market by means of a deductive analysis of historical data and observation of changes in the structure of resources based on generally available macroeconomic data. The authors evaluate these processes against the background of demographic and economic changes, by presenting...
-
PRZE-MIESZKIWANIE [w ramach:] PUSTKA, wystawa zbiorowa
Publication„Prze-mieszkiwanie” to praca ukazująca podstawową potrzebę i konieczność zapewnienia sobie przez wszelkie organizmy żywe, w tym w szczególności przez człowieka, bezpiecznej kryjówki w obliczu dojmującego poczucia postpandemicznej pustki i przymusowej izolacji, ale też kulturowego wykorzenienia. Metaforyczne wyobrażenia archetypicznej formy schronienia pokazuje jej adaptowalność do różnorodnych uwarunkowań, gdzie kontekst stanowi...
-
Real-time isothermal DNA amplification monitoring in picoliter volumes using an optical fiber sensor
PublicationRolling circle amplification (RCA) of DNA can be considered as a great alternative to the gold standard polymerase chain reaction (PCR), especially during this pandemic period, where rapid, sensitive, and reliable test results for hundreds of thousands of samples are required daily. This work presents the first research to date on direct, real-time and label-free isothermal DNA amplification monitoring using a microcavity in-line...
-
Szybkie wykrywanie wirusa grypy we wczesnej fazie rozwoju za pomocą sensorów nanodiamentowych domieszkowanych borem
PublicationPrzedstawiono konstrukcję i wyniki wstępnych badań szybkiego elektrochemicznego sensora wykonanego na bazie cienkich warstw nanokrystalicznego diamentu domieszkowanego borem, który umożliwia wykrywanie śladowych ilości wirusa grypy we wczesnej fazie rozwoju. Zapewnia to identyfikację ognisk pandemii.
-
Sugar Fee in Poland as an Example of New Fiscal Burdens and Stimulation of Consumer Behaviour
PublicationDuring the economic downturn caused by the COVID-19 pandemic, the amount and structure of tax burdens imposed by the state on businesses continue to increase, as shown on the example of the newly introduced sugar fee. A new tax-related burden imposed on businesses and consumers producing and consuming sugar-sweetened beverages appeared at the beginning of 2021. The aim of the paper is to present the fiscal burdens that accompany...
-
Ultrasound assisted synthesis of 3-alkynyl substituted 2-chloroquinoxaline derivatives: Their in silico assessment as potential ligands for N-protein of SARS-CoV-2
PublicationIn view of recent global pandemic the 3-alkynyl substituted 2-chloroquinoxaline framework has been explored as a potential template for the design of molecules targeting COVID-19. Initial in silico studies of representative compounds to assess their binding affinities via docking into the N-terminal RNA-binding domain (NTD) of N-protein of SARS-CoV-2 prompted further study of these molecules. Thus building of a small library of...
-
Water Needs of the Ash-Leaved Maple (Acer negundo L.) at the Period Over Three Years after Reclamation in Different Regions of Poland
Publication -
Facilitators and barriers to adaptive implementation of the Meeting Centers Support Program (MCSP) in three European countries; the process evaluation within the MEETINGDEM study
Publication -
The extended model predictive-sliding mode control of three-level AC/DC power converters with output voltage and load resistance variations
Publication -
Farmyard manure alone and combined with immobilizing amendments reduced cadmium accumulation in wheat and rice grains grown in field irrigated with raw effluents
Publication -
Unusual fluorescence anisotropy spectra of three-component donor-mediator-acceptor systems in uniaxially stretched polymer films in the presence of energy transfer
PublicationW pracy analizowano transfer energii w układzie donor-mediator-akceptor w osiowo rozciąganych foliach polimerowych. Stwierdzono, że informacja zawarta w orientacji wektora pola elektrycznego wiązki światła wzbudzającego układ jest zachowana po zajściu procesu transferu energii pomiędzy molekułami w foliach rozciąganych. Natomiast w foliach nierozciąganych fluorescencja mediatora i akceptora jest bardzo silnie zdepolaryzowana.
-
Three-dimensional fractographic analysis of total fracture areas in 6082 aluminium alloy specimens under fatigue bending with controlled damage degree
Publication