Search
Filters
total: 1923
filtered: 1718
displaying 1000 best results Help
Search results for: SCRAP TYRES
-
Modification of microporous polyurethane elastomers with different types of ash—morphological, mechanical, and thermal studies
PublicationIncorporation of wood ash particles from wood gasification into microporous polyurethane elastomers has been investigated and compared to addition of commercially available microspheres resulting from coal burning. Samples were modified with 3 and 6 wt% of fillers. Structure, mechanical, and thermal properties of obtained elastomers were investigated. Incorporation of both types of ash particles decreased the density of polyurethanes...
-
Comparison of different types of electronic nose instruments for evaluation of odour nuisance from landfill
PublicationThe paper presents and compares the results of investigation on classification of atmospheric air samples collected in a vicinity of municipal landfill with respect to their odour nuisance. The research was conducted using a prototype of electronic nose instrument and a commercial electronic nose of Fast/Flash GC type – HERACLES II. The prototype was equipped with six semiconductor sensors of TGS type. Classification of the air...
-
Permeation and sorption properties of poly(ether-block-amide) membranesfilled by two types of zeolites
PublicationThe experimental study of transport properties of mixed matrix membranes (MMMs) based on PEBA-4033 with two types of zeolites is reported. Gas (CO2, O2, N2) and vapor (benzene, toluene, methanol, water) permeation measurements were performed using the differential flow permeameter at temperature of 298.15 K and at atmospheric pressure. Gas/vapor permeation was monitored by measuring the changes of the thermal conductivity of carrier...
-
An analysis of wind conditions at pedestrian level in the selected types of multi-family housing developments
PublicationThe following article addresses the issue of wind conditions around urban building development at pedestrian level. Factors that depend on those issues include wind comfort and air quality within urbanized spaces. The conditions specific of cities located in a temperate climate zone have been taken into account. The article is intended to identify aerodynamic phenomena characteristic of the three basic types of multi-family building...
-
Pyrolysis of Pruning Residues from Various Types of Orchards and Pretreatment for Energetic Use of Biochar
PublicationThe routine pruning and cutting of fruit trees provides a considerable amount of biowaste each year. This lignocellulosic biomass, mainly in the form of branches, trunks, rootstocks, and leaves, is a potential high-quality fuel, yet often is treated as waste. The results of a feasibility study on biochar production by pyrolysis of residues from orchard pruning were presented. Three types of biomass waste were selected as raw materials...
-
Foamed Polyurethane Composites With Different Types of Ash – Morphological, Mechanical and Thermal Behavior Assessments
Publicationncorporation of two types of ash particles into flexible polyurethane foams has been investigated, wood ash from gasification process and fly ash resulting from coal burning in power plant. Samples were modified with 5, 10 and 15 wt% of fillers. Structure, mechanical and thermal properties of obtained foams were investigated. Incorporation of both types of ash particles resulted in materials showing...
-
Direct Analysis of Samples of Various Origin and Composition Using Specific Types of Mass Spectrometry
PublicationOne of the major sources of error that occur during chemical analysis utilizing the more conventional and established analytical techniques is the possibility of losing part of the analytes during the sample preparation stage. Unfortunately, this sample preparation stage is required to improve analytical sensitivity and precision. Direct techniques have helped to shorten or even bypass the sample preparation stage; and in this...
-
Optimal strategy for a single-qubit gate and the trade-off between opposite types of decoherence.
PublicationZostał zbadany proces przesyłania kwantowej informacji w dwóch różnych otoczeniach (markowskim i niemarkowskim).
-
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublicationIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublicationTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublicationIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Efficiency and proportions of waste tyre pyrolysis products depending on the reactor type—A review
PublicationThis article discusses the current use of different pyrolytic reactors, their constructions and operating principles regarding the yields of main products of waste tyre pyrolytic recycling. Whether one makes a larger or smaller profit, or even a loss due to a surcharge being levied on waste tyre recycling, depends on the sale of the pyrolysis products (gas, char, oil), the proportions and market prices of which differ. The cheapest...
-
Experimental analysis of the behaviour of different types of joints in the steel structure model subjected to earthquake loading
PublicationThe present paper reports the results of the experimental study performed to investigate the behaviour of two different types of joints (destroyed and welded ones) in the model of the steel structure under seismic excitations. The structure was subjected to three earthquakes, namely Kobe, Loma Prieta and Northridge, using the shaking table investigation. The results obtained from the study...
-
Long-term effect of ZnO and CuO nanoparticles on soil microbial community in different types of soil
Publication -
How Entrepreneurial Orientation Stimulates Different Types of Knowledge in the Internationalisation Process of Firms from Poland?
Publication -
Static renewal and continuous-flow calibration of two types of passive samplers for the monitoring of pharmaceuticals in wastewater
Publication -
Simulated Annealing Based on Linguistic Patterns: Experimental Examination of Properties for Various Types of Logistic Problems
Publication -
Fixed-Dose Combination of NSAIDs and Spasmolytic Agents in the Treatment of Different Types of Pain—A Practical Review
Publication -
Computational Simulation of the Effects of Different Culture Types and Leader Qualities on Mistake Handling and Organisational Learning
PublicationThis chapter investigates computationally the following research hypotheses: (1) Higher flexibility and discretion in organisational culture results in better mistake management and thus better organisational learning, (2) Effective organisational learning requires a transformational leader to have both high social and formal status and consistency, and (3) Company culture and leader’s behavior must align for the best learning...
-
Predicting seismic response of SMRFs founded on different soil types using machine learning techniques
PublicationPredicting the Maximum Interstory Drift Ratio (M-IDR) of Steel Moment-Resisting Frames (SMRFs) is a useful tool for designers to approximately evaluate the vulnerability of SMRFs. This study aims to explore supervised Machine Learning (ML) algorithms to build a surrogate prediction model for SMRFs to reduce the need for complex modeling. For this purpose, twenty well-known ML algorithms implemented in Python software are trained...
-
Seismic gap between buildings founded on different soil types experiencing pounding during earthquakes
PublicationSeveral formulas have been suggested in the literature to evaluate the minimum seismic gap that would prevent collisions between adjacent buildings during earthquakes, including those based on the absolute sum of the peak displacements (ABS), square root of the sum of the squares (SRSS), the double difference method (DDC), Australian code, and approach proposed by Naderpour et al. The aim of the present study is to evaluate the...
-
Shaking table experimental study on pounding between adjacent structures founded on different soil types
PublicationThe aim of this study is to extensively investigate the effect of the soil type on the response of colliding structures based on shaking table experimental tests. Two single-storey models of steel buildings with different dynamic parameters were considered in this study. Three pounding scenarios were taken into account by applying different seismic gaps (0.5 cm, 1 cm and 1.5 cm as well as the no pounding case). First, the effect...
-
Influence of various types of light on growth and physicochemical composition of blueberry (Vaccinium corymbosum L.) leaves
Publication -
An additional result of Monsuur`s paper about intrinsic consistency thres-hold for reciprocal matrices
PublicationArtykuł dotyczy zagadnienia szeregowania czynników z wykorzystaniem metody porównywania parami. Pokazuje, że metoda logarytmicznych najmniejszych kwadratów, stosowana w procesie aproksymacji macierzy ocen w celu obliczenia uszeregowania nie powoduje utraty wagi w przeciwieństwie do powszechnie stosowanej metody maksymalnej wartości własnej.
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublicationSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-off adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by...
-
Influence of different types of the internal system of the ballistic helmet shell on the thermal insulation measured by a manikin headform
Publication -
The activity of antioxidant enzymes in blood platelets in different types of renal replacement therapy: a cross-sectional study
Publication -
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four Different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-of adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by cyclic...
-
Employing Subjective Tests and Deep Learning for Discovering the Relationship between Personality Types and Preferred Music Genres
PublicationThe purpose of this research is two-fold: (a) to explore the relationship between the listeners’ personality trait, i.e., extraverts and introverts and their preferred music genres, and (b) to predict the personality trait of potential listeners on the basis of a musical excerpt by employing several classification algorithms. We assume that this may help match songs according to the listener’s personality in social music networks....
-
Thermo-oxidative exfoliation of carbon black from ground tire rubber as potential reinforcement in green tires
PublicationConsidering the balance between rapidly growing global tire demand and scarcity of natural resources, recycling and reclaiming techniques of tire rubber have become the state of the art. Herein, we set out to implement a self-designed thermo-oxidative reactor for the exfoliation of carbon black (CB) from ground tire rubber, which is efficiently functioned under a thermo-oxidative reclaiming condition without any additive. The exfoliation...
-
Evaluation of the stiffness modulus and phase angle of cold in-place recycled mix-tures for long curing periods
PublicationArticle presents the changes inbehaviour of cold-in place recycling mixtures made using cement and bituminous emulsion (CIR mixtures) after anelongated time of curing. Most of the available literatureregarding change instiffness modulus and phase angle presents resultsfor a maximum of several dozen days,which makesit difficult to predict the behaviour over the whole life of the compacted layer. The article...
-
Grafting and reactive extrusion technologies for compatibilization of ground tyre rubber composites: Compounding, properties, and applications
PublicationChemical modification of ground tyre rubber (GTR) to compatibilize it with the matrix is a well-known approach. Based on our recent review of the surface etching methods used in GTR modification, the purpose of the current work is to take a deeper look into more advanced methods such as grafting and reactive extrusion. While grafting is more efficient in achieving compatibility, however, it usually involves multi-step synthesis...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublicationThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Wind Conditions at Pedestrian Level in Different Types of Residential Urban Development for a High Degree of Land Use Efficiency
PublicationThe paper concerns wind conditions around urban building development at the pedestrian level. The article aims to identify aerodynamic phenomena around three types of multi-family housing developmentswith different forms and the same urban parameters of building development intensity (high intensity was taken into account). The aim of the research was mainly to achieve qualitative results that would lead to understanding fundamental...
-
Investigations into Exhaust Particulate Emissions from Multiple Vehicle Types Running on Two Chassis Dynamometer Driving Cycles
Publication -
Types of Depression More Frequent in Bipolar than in Unipolar Affective Illness: Results of the Polish DEP-BI Study
Publication -
Tuning Optical and Granulometric Properties of Gold Nanostructures Synthesized with the Aid of Different Types of Honeys for Microwave-Induced Hyperthermia
Publication -
An Adaptive Network Model Simulating the Effects of Different Culture Types and Leader Qualities on Mistake Handling and Organisational Learning
PublicationThis paper investigates computationally the following research hypotheses: (1) Higher flexibility and discretion in organizational culture results in better mistake management and thus better organizational learning, (2) Effective organizational learning requires a transformational leader to have both high social and formal status and consistency, and (3) Company culture and leader’s behavior must align for the best learning effects....
-
Soiling Effect Mitigation Obtained by Applying Transparent Thin-Films on Solar Panels: Comparison of Different Types of Coatings
PublicationDust accumulation on the front cover of solar panels is closely linked to location and orientation of photovoltaic (PV) installation. Its build-up depends on the module tilt angle, frequency of precipitation, humidity, wind strength and velocity, as well as grain size. Additionally, soil composition is determined by solar farm surroundings such as local factories, agricultural crops, and traffic. Over time, molecules of atmospheric...
-
An Adaptive Network Model Simulating the Effects of Different Culture Types and Leader Qualities on Mistake Handling and Organisational Learning
PublicationThis paper investigates computationally the following research hypotheses: (1) Higher flexibility and discretion in organizational culture results in better mistake management and thus better organizational learning, (2) Effective organizational learning requires a transformational leader to have both high social and formal status and consistency, and (3) Company culture and leader's behavior must align for the best learning effects....
-
Solid phase extraction clean up of soil and sediment extracts for the determination of various types of pollutants in a single run.
PublicationOpisano nową procedurę oczyszczania ekstraktów rozpuszczalnikowych (uzyskanych w trakcie obróbki próbek gleby i osadów dennych) z wykorzystaniem techniki ekstrakcji do fazy stałej. Oryginalność podejścia polega na znalezieniu takiej kombinacji sorbentów, że uzyskuje się ekstrakt przygotowany do analizy chromatograficznej na zawartość różnych typów zanieczyszczeń (polichlorowane bifenyle, wielopierścieniowe węglowodory aromatyczne,...
-
Influence of temperature and interactions with ligands on dissociation of dsDNA and ligand-dsDNA complexes of various types of binding : an electrochemical study.
PublicationSeveral medicinally important compounds that bind to dsDNA strands via intercalation (C-1311, C-1305, EtBr), major groove binding (Hoechst 33258) and covalent binding (cis-Pt) were examined. The obtained results suggest that both the transfer of conformation B to C and the denaturation process, for the ligand-dsDNA complexes, except for covalently bound cis-Pt, took place at higher temperatures compared to the unbound helix. Furthermore,...
-
Noise Analysis of Continuous GPS Time Series of Selected EPN Stations to Investigate Variations in Stability of Monument Types
PublicationThe type of monument that a GPS antenna is placed on plays a significant role in noise estimation for each permanent GPS station. In this research 18 Polish permanent GPS stations that belong to the EPN (EUREF Permanent Network) were analyzed using Maximum Likelihood Estimation (MLE). The antennae of Polish EPN stations are placed on roofs of buildings or on concrete pillars. The analyzed data covers a period of 5 years from 2008...