Filters
total: 488
filtered: 452
Search results for: VISCOELASTIC PIPE
-
Viscoelastic lubrication of human hip joint for impulsive motion after injury. Lepkosprężyste smarowanie stawu biodrowego człowieka dla impulsywnego ruchu po urazie.
PublicationW pracy rozpatruje się urazy wywołujące zmniejszenie lub zwiększenie wysokości i zmiany kształtu szczeliny stawu, które to zmiany po pewnym określonym czasie po doznanym urazie mogą zanikać. W konsekwencji takich urazów i to w bardzo krótkim czasie rzędu mikrosekund następują bardzo istotne zmiany parametrów smarowania. Mamy tu na uwadze zmiany rozkładów wartości ciśnienia i sił nośnych. Takie zmiany warunków smarowania nieustalonego...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublicationThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublicationThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Forecasting values of cutting power for the sawing process of impregnated pine wood on band sawing machine
PublicationW artykule przedstawiono prognozowane wartości mocy skrawania dla pilarki taśmowej (ST100R firmy STENNER), które są stosowane w polskich tartakach. Wartości mocy skrawania oszacowano dla drewna sosny zwyczajnej (Pinus sylvestris L.), które zostało poddane impregnacji. Dla porównania wyznaczono również wartości mocy skrawania dla drewna niezaimpregnowanego. Wartości te określono za pomocą innowacyjnej metody prognozowania sił skrawania,...
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublicationIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Unsteady periodic pressure and capacity for viscoelastic lubrication in spherical hip joint. Nieustalone okresowe ciśnienie i nośność w lepkosprężystym smarowaniu sferycznego stawu biodrowego.
PublicationNiniejsza praca przedstawia obliczenia numeryczne rozkładu wartości ciśnienia i siły nośnej podczas hydrodynamicznego smarowania w szczeliny stawu biodrowego człowieka przy uwzględnieniu okresowego ruchu niestacjonarnego oraz lepkosprężystych właściwości cieczy synowialnej, zmieniających się w czasie. Takie właściwości cieczy synowialnej nie były uwzględniane w dotychczasowych pracach naukowych przy modelowaniu numerycznym stawu...
-
Fatigue Damage Development in 14MoV6-3 Steel for Power Plant Pipes Monitored by Digital Image Correlation
Publication -
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publication -
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Effect of Thermal Shock During Legionella Bacteria Removal on the Corrosion Properties of Zinc-Coated Steel Pipes
PublicationThe purpose of this investigation was to conduct the failure analysis of a water-supply system made from zinc-coated steel. The observed corrosion process had an intense and complex character. The brownish deposits and perforations were present after 2-3 years of exploitation. The electrochemical study based on the Tafel polarization, corrosion potential monitoring, and electrochemical impedance spectroscopy together with microscopic...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Viscoplastic damage analysis of plate-shell structures subjected to impact loading = Lepkoplastyczna analiza zniszczenia konstrukcji płytowo-powłokowych pod wpływem obciążeń dynamicznych
PublicationW pracy przedstawiono rozważania nad analizą zachowania się konstrukcji płytowo-powłokowych pod wpływem obciążeń dynamicznych wzbudzanych przez eksplozje mieszanki gazowej. Zagadnienie to jest poddane badaniom ukierunkowanym na aspekty mechaniczne, głównie na przewidywanie ciągliwego zniszczenia. W pierwszej kolejności zaprezentowano przegląd literatury oraz opisano teorie, które w dzisiejszych czasach są najczęściej stosowane...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationAbstract: The mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also on the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationThe mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete Element Methods....
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Can Post-Activation Performance Enhancement (PAPE) Improve Resistance Training Volume during the Bench Press Exercise?
Publication -
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Influence of Wood Moisture on Strength and Elastic Modulus for Pine and Fir Wood Subjected to 4-point Bending Tests
PublicationThe main purpose of this research paper was to determine the influence of the wood moisture on the strength and elastic modulus of pine and fir wood specimens subjected to the 4-point bending tests. Six bending tests for each wood species and for two different moisture level have been performed. Then, the advanced statistical analysis of the results has been carried out. On the basis of the obtained results, it has been noted that...
-
The effect of the annual growth and the late wood share upon density of the Polish pine wood as a function of its origin
PublicationW artykule przedstawiono zróżnicowanie gęstości polskiego drewna sosnowego (Pinus sylvestris L.) w zależności od udziału drewna późnego w przyroście rocznym z uwzględnieniem krainy pochodzenia drewna. Wspomniane zróżnicowanie jest w istotne statystycznie w skali globalnej oraz dla większości miejsc pochodzenia. Pomiar gęstości wykonano przy użyciu metody stereometrycznej. Metoda ta polegała na określeniu objętości pryzmy poprzez...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublicationThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublicationThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublicationWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Image Representation for Cognitive Systems Using SOEKS and DDNA: A Case Study for PPE Compliance
PublicationCognitive Vision Systems have gained significant interest from academia and industry during the past few decade, and one of the main reasons behind this is the potential of such technologies to revolutionize human life as they intend to work under complex visual scenes, adapting to a comprehensive range of unforeseen changes, and exhibiting prospective behavior. The combination of these properties aims to mimic the human capabilities...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Fatigue damage development in 10CrMo9-10 steel for power plant pipes in as-received state and after 280,000 h of exploitation
Publication -
IMPLEMENTATION OF THE POST-SYNODAL APOSTOLIC EXHORTATION "AMORIS LAETITIA" OF POPE FRANCIS IN THE PASTORAL CARE OF IRREGULAR SITUATIONS IN THE DIOCESE OF PŁOCK
Publication -
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublicationIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublicationIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
Spatial variability of throughfall in a stand of Scots pine (Pinus sylvestris L.) with deciduous admixture as influenced by canopy cover and stem distance
PublicationVegetation cover affects the amount of precipitation, its chemical composition and its spatial distribution, and this may have implications for the distribution of water, nutrients and contaminants in the subsurface soil layer. The aim of this study was a detailed diagnosis of the spatio-temporal variability in the amount of throughfall (TF) and its chemical components in a 72-year-old pine stand with an admixture of oak and birch....
-
Chemical Composition of Atmospheric Air in Nemoral Scots Pine Forests and Submountainous Beech Forests: The Potential Region for the Introduction of Forest Therapy
PublicationStudies show that forests are one of the main recreational destinations. This can be explained by their beneficial effects on the health of their visitors, which can be attributed to compounds from the terpene group. The aim of this research was to determine the chemical composition of air in the interiors of Nemoral Scots pine forests and submountainous beech forests, with the determination of compounds of the terpene group. Samples...
-
Comparison of two intravascular access techniques when using CBRN-PPE: A randomized crossover manikin trial
Publication -
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublicationIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublicationThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Analysis of specific cutting resistance while cutting frozen pine blocks with narrow-kerf stellite tipped saws on frame sawing machines.
PublicationPrzedstawiono wyniki analizy oporów skrawania drewna zmrożonego podczas przecierania pryzm sosnowych na pilarce ramowej za pomocą cienkich pił. Badania prowadzono dla temperatur drewna -5 st. C, -20 st. C oraz dla porównania w temperaturze +18 st. C. Wilgotność drewna wynosiła 30%. Zaobserwowano znaczacy wzrost oporów skrawania wraz ze spadkiem jego temperatury.
-
Inhibition of inflammatory response in human keratinocytes by magnetic nanoparticles functionalized with PBP10 peptide derived from the PIP2-binding site of human plasma gelsolin
Publication -
The forecasted values of cutting power for sawing on band sawing machines for Polish Scots pine wood (Pinus sylvestris L.) in a function of its provenance.
PublicationIn this paper the predicted values of cutting power for band sawing machine (EB 1800, f. EWD), which is used in the Polish sawmills, were showed. The values of cutting power were forecasted for Scots pine (Pinus sylvestris L.) wood of five provenances from Poland. These values were determined using an innovative method of predicting the cutting power, which takes into account of elements of fracture mechanics. The resulting predictions...
-
Vplyv modifikácie dubovégo dreva technólogiou thermo-wood na zrnistosŤ piliny z procesov pilenia dreva na rámovej pile PRW 15M
PublicationW referacie przedstawiono wpływ modyfikacji termicznej drewna dębowego technologią ThermoWood na ziarnistość wiórów z procesu przecinania na pilarce ramowej PRW15M. Stwierdzono, że trociny uzyskane z drewna dębowego modyfikowanego termicznie nie zawierają w swoim składzie szkodliwych dla układu oddechowego człowieka cząstek z frakcji PM2.5, a ponadto nie wykryto cząstek frakcji PM10, które mogłyby tworzyć smog w środowisko pracy.
-
Determination of phenylbutazone, sulfamethazine, carbendazim and linuron using a novel pine bark biosorbent for solid-phase extraction (SPE) with high-performance liquid chromatography (HPLC)
PublicationThe paper presents a novel pine bark based biosorbent for solid-phase extraction (SPE). The morphology and composition of the pine bark were characterized using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The biosorbent was used for the preparation of wastewater for the determination of phenylbutazone, sulfamethazine, carbendazim, and linuron by high performance liquid chromatography with...
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublicationThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
Initial Investigation of Wave Interactions During Simultaneous Valve Closures in Hydraulic Piping Systems
PublicationThe effects of interference of pressure waves in simple piping systems were studied. A freeware computer code Allievi developed at the University of Valencia was used to simulate dynamic waveforms in simple and complex networks. The tests were carried out according to three scenarios. No pressure increases significantly exceeding the Joukowsky pressure in simple cases were noticed. When the effects of the simultaneous closing of...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublicationCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublicationThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
Analysis of magnetic field inside thin-layer ferromagnetic objects
PublicationResults of the numerical analysis of the magnetic field inside an infinitely long, thin-layer ferromagnetic pipe with and without a barrier were presented in this paper. Two wires with current symmetrically placed on two sides of the pipe are the sources of magnetic field. Numerical calculations for the quasi-steady state for chosen frequency band were carried out in the Flux 2D.
-
Measurements of Two-phase Flows in Pipelines Using Radioisotopes and Statistical Signal Processing
PublicationThis paper presents an application of radiotracers and gamma absorption method in two-phase flow measurements in pipelines. Two different methods were implemented to analysis of acquired signals. Investigated methods are based on the cross-correlation function and the phase of the cross-spectral density distribution. The examples presented in the article illustrate the application of the radioisotopes to evaluation of liquid-gas...
-
On the Dynamics of a Visco–Piezo–Flexoelectric Nanobeam
PublicationThe fundamental motivation of this research is to investigate the effect of flexoelectricity on a piezoelectric nanobeam for the first time involving internal viscoelasticity. To date, the effect of flexoelectricity on the mechanical behavior of nanobeams has been investigated extensively under various physical and environmental conditions. However, this effect as an internal property of materials has not been studied when the...
-
Interaction Between Storm Water Conduit Flow and Overland Flow for Numerical Modelling of Urban Area Inundation
PublicationNowadays we can observe increasing frequency of inundations in cities. This makes accurate predicting of inundations more important than ever. Numerical modeling of this issue requires complex approach with simultaneous calculations of pipe flow and surface flow. In this paper, after a short review of known methods used for solving pipe and surface flow, we will try to answer the question if presented methods would be sufficiently...
-
Analiza parametrów płukania sieci wodociągowej metodą ukierunkowanego przepływu wody
PublicationEksperymenty prowadzone przez wiele lat podczas płukania sieci wodociągowej metodą jednokierunkowego przepływu wody umożliwiają weryfikację interakcji między jakością wypłukiwania nagromadzonych zanieczyszczeń oraz parametrami przepływu, liczbą cykli wymiany wody, a także zasięgiem płukania. Usuwanie zanieczyszczeń na początku przebiega zgodnie z szybko rosnącą krzywą, a następnie według funkcji malejącej. Taki przebieg jest spowodowany...