Filters
total: 1845
filtered: 1578
displaying 1000 best results Help
Search results for: transfer genów
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublicationThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Implementation of the Boundary Element Method to Two-Dimensional Heat Transfer with Thermal Bridge Effects
PublicationThe work presents an application of the boundary element method applied to a two-dimensional conductive heat transfer. The algorithm of the method is explained and its advantages are outlined. Green's function as a fundamental solution for Poisson's equation in two dimensions was used and the direct approach was applied. The presented results concern building construction elements as typical cases of thermal bridges. Some properties...
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublicationThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
The use of liquid crystal thermography and particle image velocimetry in the exploration of heat transfer measurements
PublicationArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublicationW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Transfer of charging information between exchanges of different network operators in multi-provider environment.
PublicationW pracy przedstawiono różne konfiguracje systemów taryfikacji i zaliczania w środowisku zdemonopolizowanym. Przeanalizowano różne opcje przepływu danych w takim środowisku i omówiono rozszerzenie sygnalizacji SS7, która jest opracowana przez ETSI i wykorzystywana dla aplikacji zaliczania.
-
Poly(ferrocenylsilane-block-methacrylates) via sequential anionic and atom transfer radical polymerization.
PublicationArtykuł przedstawia sposób otrzymywania kopolimerów blokowych poli(ferrocenylosilanów) (PFS) i poli(metakrylanu metylu) (PMMA). W pierwszej kolejności syntezowany jest anionowo blok PFS, który po odpowiedniej terminacji służy jako makroinicjator dla syntezy bloku PMMA. Synteza ta jest realizowana przy użyciu polimeryzacji rodnikowej z przeniesieniem atomu (ATRP), katalizowanej przez kompleksy rutenu. Otrzymane w ten sposób kopolimery...
-
Free convective heat transfer structures as a function of the width of isothermal horizontal rectangular plates
PublicationZaprezentowano rezultaty badań eksperymentalnych konwekcyjnej wymiany ciepła od izotermicznych płyt prostokątnych skierowanych ku górze. Na podstawie przeprowadzonych wizualizacji zaproponowano dwa modele struktur przepływu. Rozwiązania analityczne dla tych modeli przedstawiono w postaci zależności liczb Nusselta Rayleigh'a. Stwierdzono, że przepływ koncentryczny występuje dla małych wartości liczb Ra, szczególnie w przypadku płyt...
-
Effects of metallic silver particles on resonance energy transfer between fluorophores bound to DNA.
PublicationZbadano wpływ filmów wysepek metalicznego srebra na rezonansowe przekazywanie energii między fluoroforami związanymi z DNA. Donorem i akceptorem były odpowiednio 4´,6 diamidyno-2-fenylindon i jodek propydyny. Zmierzone dla tego układu czasy zaniku i widma fluorescencji pokazują, że sąsiedztwo cząstek srebra dramatycznie zwiększa promień Forstera, a tym samym i przekazywanie energii w znakowanym DNA.
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublicationPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Theoretical treatment of charge-transfer processes induced by collision of C^q+ ions with uracil
PublicationWychwyt ładunku został opisany teoretycznie przy użyciu podstawowych metod chemii kwantowej, uzupełnionych półklasycznym opisem dynamiki zachodzącego procesu. Otrzymane przekroje czynne pokazują zróżnicowane zachowanie pod wpływem struktury elektronowej badanego jonu i mogą służyć do wyjaśniania prowadzonych badań doświadczalnych.
-
Impedance of cation-coupled electron transfer reaction: teoretical description of one pathway process
PublicationPrzyjęto możliwość występowanie dwóch wzajemnie sprzężonych reakcji. Opisana została impedancja sprzężonej reakcji przeniesienia elektronu z kationem. Wyznaczony został również model elektrycznego schematu zastępczego. Całkowita impedancja Faradayowska jest sumą impedancji przeniesienia elektronu i impedancji przeniesienia kationu. Przykłady pomiaru impedancyjnego w warunkach potencjostatycznych i potencjodynamicznych zostały omówione....
-
Förster Resonance Energy Transfer and Trapping in Selected Systems: Analysis by Monte-Carlo Simulations
PublicationMetoda symulacji Monte Carlo została opisana i zastosowana jako efektywne narzędzie do analizy wyników pomiarów transferu energii w wybranych układach, dla których zastosowanie podejścia analitycznego jest ograniczone lub nawet niemożliwe. Pokazano, że symulacja Monte Carlo pozwala obliczyć tzw. czynnik orientacyjny dla układów częściowo uporządkowanych oraz szereg innych wielkości ważnych do opisu zjawiska transferu energii, które...
-
Comparative Evaluation of Multicoil Inductive Power Transfer Approaches Based on Z-source Network
PublicationThis paper describes comparative evaluation between wireless power transfer topologies with utilization of Z-source network. Paper describes components calculation method. List of open-loop, close-loop simulations were conducted to compare both topologies. Spectrum of signals is also researched.
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublicationThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Impact of dyes isomerization effect on the charge transfer phenomenon occurring on the dye/nanosemiconductor interface
PublicationThe present work aimed to find the answer how does the isomerization of the Ru based dyes affect the overall photon-to-current efficiency of the DSSCs and to explain the charge transfer phenomenon occurring on the dye/ nanosemiconductor interface. Therefore, electronic and optical properties of three bipyridine derivatives anchored on the TiO2 electrode were investigated by computational simulations based on quantum chemistry codes...
-
How Chain Transfer Leads to a Uniform Polymer Particle Morphology and Prevents Reactor Fouling
PublicationABSTRACT: The effect of adding diethyl zinc as a chain transfer agent during the polymerization of propylene in heptane performed at 80 °C was studied. Although it was expected that the chain transfer would stop after precipitation of the polymer, the polymer molecular weight continued to increase throughout the whole of the polymerization. The presence of diethyl zinc had an additional effect that the polymerizations were devoid...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Inter-governmental Collaborative Networks for Digital Government Innovation Transfer -Structure, Membership, Operation
PublicationDigital government refers to the transformation of government organizations and their relationships with citizens, business and each other through digital technology. It entails digital innovation in processes, services, organizations, policies, etc. which are increasingly developed and tested in one country and transferred, after adaptation, to other countries. The process of innovation transfer and the underlying information...
-
The Knowledge Transfer From Headquarter to Local Subsidiaries Through Expatriates - Local Employees’ Perspective
PublicationBackground. Knowledge transfer between the HQ and subsidiary has recently been targets of increasing research interest. However, the role of expatriate managers and local staff perspective on this process has not been examined enough. Research aims. This paper has two main objectives: first to develop a conceptual framework (model) of knowledge transfer between the headquarters and local subsidiary, and second to empirically evaluate...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublicationThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublicationAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publicationmodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Navigational decision support system during approach manoeuvre in emergency STS transfer operation
PublicationThe paper is concerned with the problem of safe trajectory planning for approaching during emergency STS (Ship to Ship) transfer operation with oil spill. The safe trajectory means that the way points does not cross in the area of the environment with the static and dynamic obstacles and at the same time satisfies ship's stopping and speed deceleration performance. The evolutionary path planning algorithm is used to determine trajectory...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublicationIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Modelling of two-component turbulent mass and heat transfer in air-fed pressurised suits
PublicationIn this paper the modelling of an important industrial problem is addressed, which involves the two-component turbulent flow with heat transfer that takes place inside protective clothing. The geometry of the flow boundaries is reconstructed in a CAD system from photogrammetry scan data. The overall model is sufficiently realistic to allow, after validation, design improvements to be tested. Those presented here allow the reduction...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
BODIPY‐Perylene Charge Transfer Compounds; Sensitizers for Triplet‐Triplet Annihilation Up‐conversion
PublicationBODIPY heterochromophores, asymmetrically substituted with perylene and/or iodine at the 2 and 6 positions were prepared and investigated as sensitizers for triplet-triplet annihilation up conversion (TTA-UC). Single-crystal X-ray crystallographic analyses show that the torsion angle between BODIPY and perylene units lie between 73.54 and 74.51, though they are not orthogonal. Both compounds show intense, charge transfer absorption...
-
Główne bariery w systemie transferu technologii w Polsce
PublicationNiniejszy artykuł poświęcony jest omówieniu najważniejszych barier wy-stępujących w systemie transferu technologii i komercjalizacji wiedzy w Polsce. Na wstępie autorka, opierając się na analizie dostępnych danych źródłowych przytacza te wyniki badań, które obrazują główne obszary problemowe w każ-dym z ogniw tego systemu: przedsiębiorstwach, jednostkach B+R oraz instytu-cjach otoczenia biznesu. W dalszej części artykułu autorka...
-
The Farrow structure for the Hilbert transform filter
PublicationPrzedstawiono nową implementację cyfrowego filtru Hilberta, wykonaną w strukturze Farrowa. Jest to filtr zespolony, realizujący jednocześnie dwie różne operacje liniowe, wykonywane dotychczas za pomocą osobnych filtrów. Pierwsza z nich polega na standardowej filtracji hilbertowskiej. Tworzy ona zespolony "analityczny" odpowiednik rzeczywistego sygnału wejściowego. Drugą, osiąganą za pomocą prze-próbkowania ze współczynnikiem, w...
-
Evaluation of Hilbert transform filter performance
PublicationW pracy rozpatrzono zagadnienie adaptacyjnej estymacji ułamkowego opóźnienia pomiędzy dwoma sygnałami sinusoidalnymi. Zastosowano tu nowy, zagregowany, zespolony filtr Hilberta, który łączy w sobie funkcje filtracji Hilberta i kompensacji ułamkowego opóźnienia. W eksperymentach wykorzystano efektywną implementację tego filtru w strukturze Farrowa, której jedynym parametrem o zmiennej wartości jest bieżące opóźnienie ułamkowe.
-
Heat transfer to car engine cooling system - influence of coolant flow through engine block
PublicationW artykule przedstawiono wyniki badań doświadczalnych nad wpływem nastawianej wydajności pompy cieczy na strumień odbieranego ciepła w silniku spalinowym. Wykorzystano hamownię silnikową z silnikiem o zapłonie iskrowym o objętości skokowej 1.8 dm^3. Przyjęto obciążenia silnika oporami ruchu samochodu na biegu bezpośrednim.
-
Influence of charge transfer state on Eu 3+ luminescence in LaAlO 3 , by high pressure spectroscopy
Publication -
New type of repeated Si–C-podand catalysts for solid–liquid phase transfer reactions
Publication -
Proton transfer reactions from some diarylcyanomethanes to cis 1,2-bis(diethylaminomethyl)cyclohexane in acetonitrile
Publication -
Implementation of Fluidized Bed Concept to Improve Heat Transfer in Ecological Adsorption Cooling and Desalination Systems
Publication -
A Study of the Impact of Internal and External Usability on Knowledge Transfer by the Means of Mobile Technologies: Preliminary Results
Publication -
Novel Approach to Mo93m Isomer Depletion: Nuclear Excitation by Electron Capture in Resonant Transfer Process
Publication -
P-544 Biochemical markers as a predictor of clinical pregnancy on day 6 after embryo transfer
Publication -
Possible mechanisms for protecting NCα bonds in helical peptides from electron-capture (or transfer) dissociation
Publication -
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Interspecies distances between propionic acid degraders and methanogens in syntrophic consortia for optimal hydrogen transfer
PublicationA mixed culture from an anaerobic biowaste digester was enriched on propionate and used to investigate interspecies hydrogen transfer in dependence of spatial distances between propionate degraders and methanogens. From 20.3 mM propionate, 20.8 mM acetate and 15.5 mM methane were formed. Maximum specific propionate oxidation and methane formation rates were 49 and 23 mmol mg−1day−1, respectively. Propionate oxidation was inhibited by...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublicationW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Characteristics of the Conjugative Transfer System of the IncM Plasmid pCTX-M3 and Identification of Its Putative Regulators
Publication -
Analysis of the enthalpies of transfer of Co(II) ion in mixed solvents by means of the theory of preferential solvation.
PublicationZa pomocą teorii solwatacji preferencyjnej zanalizowano entalpie przeniesienia jonu Co(II) w kilku mieszaninach wodno-organicznych i organicznych, wyznaczając parametry, które w sposób ilościowy opisują solwatację preferencyjną jonu i jego wpływ na oddziaływania między cząsteczkami rozpuszczalnika. Przeprowadzono porównanie właściwości solwatacyjnych mieszanin. Wyznaczono także średni skład sfery solwatacyjnej jonu w zależności...
-
Rate of bitumen film transfer from a quartz surface to an air bubble as observed by optical microscopy.
PublicationSzybkość przeniesienia filmu bitumu z powierzchni płytki kwarcowej na powierzchnię pęcherzyka powietrza w roztworze alkalicznym została udokumentowana zdjęciami.