displaying 1000 best results Help
Search results for: TOMBOLO PHENOMENON
-
Indoor atmospheric degradation of historical metal objects studied by spectroscopic techniques
Publication -
Perovskites in Solid Oxide Fuel Cells
PublicationPrzeglądowa publikacja dotycząca wykorzystania ceramicznych materiałów perowskitowych w tlenkowych ogniwach paliwowych.
-
Preparation and characterization of TiO2 nanostructures for catalytic CO2 photoconversion
PublicationThe titanium dioxide target (99.7%) of 1 cm in dia was ablated in vacuum by laser pulses(6 ns) at 266 nm and at repetition rate of 10 Hz. During deposition the laser fluence between 1 and 3.5 J/cm2 and the O2 pressure from the range of 10-2 - 1 Pa were applied. The thin TiO2 films were deposited on glass substrate (1 × 1 cm2) heated up to 500 °C. The chemical composition of the film and samples produced by annealing were investigated...
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publication -
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
The Characteristic of Surface Layers on Austenitic Stainless SteelAfter Glow-discharge Nitriding Process.
PublicationThis paper presents investigation of surface layers. The diffusion layers were produced by using different parameters of reactive atmosphere (N2:H2). The research of the surface layers was performed using scanning electron microscope (SEM). The results of energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD) analysis are presented. Research reveals the influence of chemical constitution of reactive atmosphere on the...
-
The Effect Fabrication Method of Cobalt Base Clad Layer On Air Oxidation
PublicationNapawane warstwy ze stopu kobaltu zostały wykonane za pomocą napawania plazmowego (PTA) oraz laserowego. Zostały one poddane utlenia niu w temperarurze 1100 stopni celsiusza prze 200 godzin. Przeprowadzono badania mikrostruktury i składu chemicznego warstwy tlenkowej oraz głębszych warstw napoiny. Nie stwierdzono wpływu metody wytwarzania na skutki procesu utleniania.
-
Simulation and Experiments of High Speed Machining Vibration Monitoring with Variable Spindle Velocity
PublicationArtykuł poświęcony jest nadzorowaniu drgań wirujących narzędzi podczas obróbki szybkościowej na nowoczesnych centrach frezarskich. Przeprowadzono analizę dynamiki procesu skrawania smukłym frezem kulistym. W celu zredukowania drgań zastosowano, z powodzeniem, zmienną prędkość obrotową narzędzia. Badania symulacyjne dotyczące efektywności proponowanej metody zostały potwierdzone wynikami badań eksperymentlanych na frezarce Alcera...
-
Application of Syntactic Pattern Recognition Approach in Design and Optimisation of Group Machining Systems
PublicationRozwinięto koncepcję budowy zoptymalizowanych struktur systemów wytwarzania grupowego spektrum części z wykorzystaniem modelu analizy syntaktycznej sekwencji operacji ich procesów technologicznych. Określono formułę metryki odległościowej opisu stopnia zróżnicowania marszrut indywidualnych procesów oraz testowano jej skuteczność w aspekcie eksploracji wielowymiarowych danych i klasteryzacji obiektów wg cech wymagań technologicznych....
-
Cobalt Base Clad Layer Resistance On The Corrosion Under Low Sulfur Preassure
PublicationNapawane laserowo warstwy ze stopu kobaltu, zostały poddane siarkowaniu przy niskich ciśnieniach cząstkowych w temperaturze 800 stopni celsiusza prze 24 godziny. Uzyskano warstwę zgorzeliny zróżnicowaną w zależności od zastosowanego ciśnienia. W obu jednak przypadkach podobne były zmiany zachodzące w warstwie po zgorzeliną - degradacja węglików i intensywna korozja wzdłuż granic dendrytów.
-
Influence of cavitation intensity on the relative cavitation resistance of laser processed C45 carbon steel
PublicationPraca przedstawia badania względnej odporności kawitacyjnej we wstępnym okresie niszczenia laserowo przetopionej 6 kW laserem CO2 stali C45. Badania odporności kawitacyjnej wykonano na stanowisku z wirującą tarczą. Na erodowanej przetopionej warstwie powierzchniowej określono trzy obszary o różnej intensywności oddziaływania obciążeń kawitacyjnych. Określano wielkość odkształceń plastycznych w analizowanych obszarach, spowodowanych...
-
Cavitation Erosion Resistance of Austenitic Microstructure Created byLaser Beam
PublicationPraca przedstawia własności kawitacyjne różnych mikfrostruktur austenitycznych tworzonych za pomocą wiązki lasera na stalach X5CrNi18-10 oraz C45. Stal X5CrNi18-10 była laserowo stopowana węglikiem TiC oraz stopowana Ni, Mn, Cr i Nb. Jako żródło mocy stosowany był laser CO2. Własności kawitacyjne oceniane były na stanowisku z wirującą tarczą. Badania ujawniły różną podatność struktury austenicycznej do odkształceń plastycznych...
-
Limb/Ground Impacts and Unexpected Impacts Control Strategy for a Model of a Limb of a Walking Robot
PublicationPraca prezentuje wyniki analizy numerycznej dynamiki robota kroczącego. Uwaga skoncentrowana jest na zagadnieniu kontaktu odnóża z podłożem. W kierunku normalnym kontakt opisano więzami jednostronnymi. W kierunku stycznym, założono obecność poślizgu i tarcia. Z uwagi na jednostronność kontaktu, może się on rozpocząć z niezerową prędkością względną. Z chwila rozpoczęcia kontaktu, prędkości zmieniają się gwałtownie. Towarzysza temu...
-
Rigid Finite Element Modeling for Identification of Vibrations in Elastic in Elastic Rod Driven by a DC-motor Suplied from a Thyristor Rectifier
PublicationRozdział dotyczy analizy numerycznej układu elektromechanicznego. Układ składa się z silnika zasilanego z jednopołówkowego prostownika tysystorowego i napędzanego tym silnikiem wirującego pręta. Celem obliczeń jest określenie postaci i wielkości drgań pręta, jeśli uwzględniamy jego elastyczność. Dyskretna struktura modelu to łańcuch wielomasowy ciał - sztywnych ciał połączonych bezmasowymi węzłami. Autorzy obliczyli zachowanie...
-
The automation of test stand for engine cooling system testing
PublicationW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
Generation of Optimal Process Plan Alternatives for ManufacturingMechanical Components
PublicationOmówiono aktualny stan wiedzy dotyczący wykorzystania systemów komputerowo wspomaganego projektowania procesów technologicznych - CAPP. Przedstawiono problemy związane z integracją systemów CAPP z systemami CAD. Omówiono założenia dla generowania optymalnych wariantów procesów wytwarzania z zastosowaniem modułów technologicznych tzw. features, wg metody gałęzi i ograniczceń (ang. branch-and-bound).
-
Mechatronic system for automatic inspection of circular saw teeth
PublicationArtykuł prezentuje system mechatroniczny do automatycznej oceny geometrii ostrzy pił tarczowych. Opisywany system wizyjny został zastosowany w automatycznym kontrolerze ostrzy pił tarczowych WKOPTar. Wrzeciono urządzenia posiada swój napęd sterowany bezstopniowo obrazem ostrzy i zapewnia powtarzalne pozycjonowanie ostrzy w celu przechwycenia ich obrazów, które są następnie analizowane z wykorzystaniem specjalnego oprogramowania....
-
Modelling of Ship’s Heeling and Rolling for the Purpose of Gantry Control Improvement in the Course of Cargo Handling Operations in Sea Ports
PublicationThe paper presents two proposals of models of interaction between a ship and cargo being loaded or discharged by a gantry in port, in terms of heeling and rolling of the vessel. The main purpose of such modelling is the need for improvement of gantry control with regard to faster operations thanks to more accurate estimation of level and moment of cargo release from a gantry hook or spreader. The study may be the contribution to...
-
Phase investigations of copper based CuZn38Al2MnFe alloy
PublicationW pracy przedstawiono analizę fazową mosiądzu CuZn38Al2MnFe. Wykazano, że obecność fazy Fe4Mn77Si19 powoduje kruchość stopu w teście zginania próbek.
-
The effect of the ceramic dispersion on the nickel matrix composite coating properties after plastic working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublicationDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Using River Formation Dynamics Algorithm in Mobile Robot Navigation
PublicationRiver Formation Dynamics is a heuristic optimization algorithm based on the manner, in which drops of water form the river bed. The idea is to imitate the movement of drops on the edges between given nodes thus performing a search based on their height, which is modified through the mechanism of soil erosion and sediment deposition. In this way decreasing gradients are constructed, and these are followed by subsequent drops to...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublicationIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublicationW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublicationAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
Determination of ability of hydrotronic systems to start in low ambient temperatures
PublicationPrzedstawiono wyniki badań symulacji komputerowej zespołów układów hydrotronicznych w warunkach szoku termicznego. Pokazano metodę określania zdatności hydrotronicznych zespołów i układów podczas rozruchu w warunkach szoku termicznego.
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Monitoring of Velocity of Manufacturing Machines Subassamblieas by Means of a DAQ System
PublicationArtykuł dotyczy dokładnych cyfrowych pomiarów prędkości ruchu podzespołów maszyn, realizowanych za pomocą enkoderów kwadraturowych, kart licznikowych DAQ oraz dedykowanych aplikacji pomiarowych DAQ. Przedstawiono koncepcje trzech różnych sposobów takiego pomiaru. W pierwszym sposobie, nazywanym ''częstotliwościowym'', pomiar odbywa się poprzez bramkowane zliczanie impulsów enkodera. Drugi sposób nazywany ''czasowym'' polega na...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublicationPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublicationThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Research of hydrotronic variable displacement radial piston pump with electro -pneumatic control
PublicationThe paper presents the developed new electro-pneumatic control (pneumotronic) system for hydraulic fixed-displacement radial piston pump. Hydraulic fixed-displacement radial piston pump equipped with the proposed control system changes into hydrotronic variable-displacement radial piston pump. Pump flow rate control is realized by means of programmable logic controller, electro-pneumatic valves, pneumatic cylinders and a sensor.
-
Port-Based Modelling of Distributed-Lumped Parameter Systems
PublicationThere in the paper is presented an uniform, port-based approach to modelling of both lumped and distributed parameter systems. Port-based model of the distributed system has been defined by application of bond graph methodology and distributed transfer function method (DTFM). The approach proposed combines versatility of port-based modelling and accuracy of distributed transfer function method. The concise representation of lumped-distributed...
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublicationW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Modal Reduction and Analysis of Gyroscopic Systems
PublicationThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublicationW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Surface Roughness Model Components Created by Stereolithography Method
PublicationW pracy przedstawiono charakterystykę powierzchni elementów wykonywanych metodą stereolitografii. Opisano modele chropowatosci stosowane do opisywania powierzcni wraz z prezentacją formuł matematycznych. W oparciu o wyniki badań eksperymentalnych przeprowadzono częściową weryfikację modeli.
-
Modeling and simulation of tool cycle in manufacturing cell
PublicationThe paper addresses issues concerning modeling and analysis of tool flow within a three-machine manufacturing cell used for small batch manufacturing of a definite spectrum of prismatic parts. The approach utilizes a method for job and tool allocation to work centers with limited number of machines and capacity of tool resources, based on the analysis of formalized relations: job - tool sets required. Selected tool flow control...
-
Optimum Control of Gyroscopic Systems
PublicationThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublicationThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublicationThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublicationThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Materials Design for the Titanium Scaffold Based Implant
PublicationThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...