Filters
total: 2000
displaying 1000 best results Help
Search results for: PITTING CORROSION
-
Developing electrochemical measurements in order to assess anti-corrosive coatings more effectively
PublicationCelem pracy było sprawdzenie powtarzalności wyników uzyskanych metodą pomiaru szumu (Electrochemical Noise method - ENM) elektrochemicznego wykonanych na powłokach organicznych w konfiguracji bez połączenia z podłożem metalowym (NOCS - No Connection to the Substrate). NOCS polega na wykonaniu pomiarów na trzech teoretycznie takich samych obszarach badanego układu. W takim układzie nie jest wymagane połączenie elektryczne z metalowym...
-
Electrochemical, theoretical and surface physicochemical studies of the alkaline copper corrosion inhibition by newly synthesized molecular complexes of benzenediamine and tetraamine with π acceptor
PublicationTwo charge transfer complexes, namely [(BDAH)+(PA−)] CT1 [(BTAH)2+(PA−)2] and CT2 (BDAH = 1,2-benzenediamine, BTAH = 1,2,4,5-benzenetetramine, and PA− = 2,4,6-trinitrophenolate), were synthesized and fully characterized using various spectroscopic techniques. CT1 and CT2 were tested as inhibitors to effectively control the uniform and anodic corrosion processes of copper in an alkaline electrolyte (1.0 M KOH) using various electrochemical...
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublicationThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
Właściwości korozyjne stopu MM55 nadtopionego laserowo w warunkach kriogenicznych = Corrosion properties of the MM55 alloy laser melted at cryogenic conditions
PublicationStop MM55 stosowany do wyrobu śrub okrętowych poddano laserowemu nadtapianiu w warunkach kriogenicznych. W artykule przeprowadzono analizę mikrostruktury warstwy wierzchniej stopu MM55 po wymienionej obróbce cieplnej. Określono właściwości korozyjne wytworzonej warstwy wierzchniej nadtopionego stopu i porównano je ze stanem wyjściowym.
-
Microstructure and corrosion behaviour of carbon steel and ferritic and austenitic stainless steels in NaCl solutions and the effect of p-nitrophenyl phosphate disodium salt
PublicationThe microstructure and corrosion behavior of carbon steel (CSA516) and ferritic (SS410) and austenitic (SS304L) stainless steels were studied and compared. Corrosion tests were carried out in 0.5 M NaCl solutions. Rates of corrosion were monitored based on weight loss, Tafel extrapolation and linear polarization resistance (LPR) methods. Rates of corrosion were ranked following the order: CSA516 >> SS410 > SS304L. The impact of...
-
Synthesis of Cyano-Benzylidene Xanthene Synthons Using a Diprotic Brønsted Acid Catalyst, and Their Application as Efficient Inhibitors of Aluminum Corrosion in Alkaline Solutions
PublicationNovel cyano-benzylidene xanthene derivatives were synthesized using one-pot and condensation reactions. A diprotic Brønsted acid (i.e., oxalic acid) was used as an effective catalyst for the promotion of the synthesis process of the new starting xanthene–aldehyde compound. Different xanthene concentrations (ca. 0.1–2.0 mM) were applied as corrosion inhibitors to control the alkaline uniform corrosion of aluminum. Measurements were...
-
Onychophagia (nail biting): A body focused repetitive behavior due to psychiatric co-morbidity.
Publication -
Formänderungsgrössenverfahren mittig gedrückter dünnwandiger Stäbe mit einfach- und doppeltsymmetrischen offenen Querschnitten
PublicationW nawiązaniu do klasycznej metody przemieszczeń dla skręcania mieszanego prętów cienkościennych, rozwinięto ją dla problematyki wyboczeń prętów. W pracy ukazano ogólne rozwiązanie podstawowego układu równań różniczkowych dla przekrojów monosymetrycznych i jego szczególne postacie dla trzech głównych sposobów podparcia pręta. Wyznaczono wzory dla bimomentów brzegowych. Związki te następnie uproszczono dla podwójnej symetrii przekroju....
-
Initial Investigation of Wave Interactions During Simultaneous Valve Closures in Hydraulic Piping Systems
PublicationThe effects of interference of pressure waves in simple piping systems were studied. A freeware computer code Allievi developed at the University of Valencia was used to simulate dynamic waveforms in simple and complex networks. The tests were carried out according to three scenarios. No pressure increases significantly exceeding the Joukowsky pressure in simple cases were noticed. When the effects of the simultaneous closing of...
-
Journal of Bio- and Tribo-Corrosion
Journals -
Journal of Corrosion Science and Engineering
Journals -
Detremination of the cutting power of the sawing process using both preliminary sawing data and modern fracture mechanics
PublicationPrzedstawiono medodykę prognozowania mocy skrawania dla procesu piłowania drewna cienkimi piłami. Przewidywanie zapotrzebowania mocy skrawania oparte jest na współczesnej mechanice pękania, a do wyznaczenia stałych materiałowych: wiązkości materiału oraz niszczących napężeń ścinających wykorzystano wyniki wstępnych badań eksperymentalnych. Błędy prognozowania nie przekraczają 15.5% dla przypadku cienkich pił gdy rolę znacząca odgrywają...
-
The Setting Time of Polyether Impression Materials after Contact with Conventional and Experimental Gingival Margin Displacement Agents
Publication -
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Narrow Red Emission Band Fluoride Phosphor KNaSiF6:Mn4+ for Warm White Light-Emitting Diodes
Publication -
Multi-Site Cation Control of Ultra-Broadband Near-Infrared Phosphors for Application in Light-Emitting Diodes
Publication -
Green Light-Excitable Ce-Doped Nitridomagnesoaluminate Sr[Mg2Al2N4] Phosphor for White Light-Emitting Diodes
Publication -
Core-shell cobalt particles Co@CoO loaded on nitrogen-doped graphene for photocatalytic water-splitting
Publication -
Measurement Of The Dynamics Of The Sheave Block Of Shipyard Crane With 1000 T Lifting Capacity For Verification Of The Laboratory Stand
Publication -
Mixing of excimer and exciplex emission: A new way to improve white light emitting organic electrophosphorescent diodes
PublicationW pracy opisano konstrukcję wydajnych diod elektrofosforescencyjnych emitujących światło białe. Emisja diod pochodzi od trypletowych monomerów PtL2Cl, trypletowych ekscymerów (PtL2Cl:PtL2Cl) i trypletowych ekscypleksów m-MTDATA (donor elektronu):PtL2Cl (akceptor elektronu), gdzie PtL2Cl oznacza organiczny kompleks platyny (II), a m-MTDATA - dendrymer aminowy. Kwantowa wydajność EL diody wynosi 6.5% fot./e. Współrzędne charakteryzujące...
-
Small-minus-big predicts betting-against-beta: Implications for international equity allocation and market timing
Publication -
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Revisiting The Determination Of Cutting Power While Sawing Of Wood With Circular Saw Blades By Means Of Fracture Mechanics
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Effect of printing direction on fatigue response and damage development in additive manufactured Haynes 282 nickel superalloy
Publication -
0D, 1D, 2D molybdenum disulfide functionalized by 2D polymeric carbon nitride for photocatalytic water splitting
Publication -
Properties of Cutting Tool Composite Material Diamond–(Fe–Ni–Cu–Sn) Reinforced with Nano-VN
Publication -
Wear of carbide inserts during turning of C45 steel in dry cutting conditions and in presence of emulsion mist
Publication -
The estimation of cutting forces and specific force coefficients during finishing ball end milling of inclined surfaces
Publication -
Modelling the Kerf Angle, Roughness and Waviness of the Surface of Inconel 718 in an Abrasive Water Jet Cutting Process
Publication -
Formation of Surface Topography During Turning of AISI 1045 Steel Considering the Type of Cutting Edge Coating
Publication -
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublicationWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
Electromodulation of fluorescence in hole-transporting materials for organic light-emitting diodes. Part II: Straburst amines
PublicationPraca jest kontynuacją artykułu, który został opublikowany wChem. Phys. vol. 256 (2000) s. 351-362. Zaobserwowano silne wygaszenie fluorescencji w dendrymerach aminowych zbudowanych na bazie trifenyloaminy. Efekt ten został przypisany rozpadowi stanów emitujących światło pod działaniem silnego pola elektrycznego.
-
Conditions of Iranian international trade in terms of lifting the sanctions: A case study of Polish-Iranian trade perspectives
PublicationThe main aim of the paper is to identify the areas and determine the feasibility of trade between Polish and Iranian companies in relation to historical and cultural conditions. The authors describe the complexity of the issue of foreign trade, the determinants of relations between Poland and the Islamic Republic of Iran, and the Iranian economy – its features, strengths and weaknesses, and consequences of the recent UN, EU, and...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Dual-Setting Bone Cement Based On Magnesium Phosphate Modified with Glycol Methacrylate Designed for Biomedical Applications
PublicationMagnesium phosphate cement (MPC) is a suitable alternative for the currently used calcium phosphates, owing to beneficial properties like favorable resorption rate, fast hardening, and higher compressive strength. However, due to insufficient mechanical properties and high brittleness, further improvement is still expected. In this paper, we reported the preparation of a novel type of dual-setting cement based on MPC with poly(2-hydroxyethyl...
-
Multiple Reprocessing of Conductive PLA 3D-Printing Filament: Rheology, Morphology, Thermal and Electrochemical Properties Assessment
PublicationAdditive manufacturing technologies are gaining more and more attention, resulting in the development or modification of 3D printing techniques and dedicated materials. On the other hand, economic and ecological aspects force the industry to develop material recycling strategies. In this work, the multiple reprocessing of a commercially available PLA conductive composite with carbon black filler, dedicated to 3D printing, was investigated....
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Advanced fatigue and rutting characterisation of Polish asphalt mixtures based on the VECD model and viscoplastic shift model
PublicationThe advanced asphalt mixture performance-related specifications (AM-PRS) recently developed in USA can allow an optimisation of the design process of asphalt pavements thanks to the possibility to fully take into account the intrinsic material properties. In this study, four typical Polish mixtures, i.e. a Stone Mastic Asphalt (SMA) for wearing course, two mixtures for binder course with neat bitumen or Polymer modified Bitumen...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublicationIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
The protective properties of graphene oxide coatings functionalized with phosphorus atoms.
PublicationRecently, electrophoretically deposited graphene oxide coatings are commonly applied as an anti-corrosion layer. However, improper adjustment of electrophoretic deposition (EPD) parameters as well as the hydrophilic nature of graphene oxide contribute to the formation of defects in the coatings and the increase in the wetting properties, respectively, and thus lead to a reduction of protective properties. The growth of wetting...
-
Dynamic impedance data for various carboxylic acids corrosion inhibition of aluminium in alkaline media (pH=11)
Open Research DataThis dataset contains the results of Dynamic Electrochemical Impedance Spectroscopy (DEIS) carried out in galvanostatic mode under iDC=0, carried out in order to define the corrosion inhibition effect of various studied carboxylic acids: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, carballylic acid, and serine. The experiment...
-
Effective perturbation signal and measurement of corrosion rate. Response to the commentary of Diard and co-workers concerning the paper in Corros. Sci. 37, 913 (1995)
Publication -
Gas corrosion influence on the exhaust valve face of the marine engine = Wpływ korozji gazowej na stan przylgni zaworów wylotowych silnika okrętowego
PublicationIstotnym czynnikiem wpływającym na poprawność funkcjonowania silnika okrętowego jest szczelność zaworów. Szczególnie w odniesieniu do zaworów wylotowych brak szczelności prowadzi do pogorszenie warunków spalania a przede wszystkim do przyspieszonego zniszczenia zawory poprzez uszkodzenia przylgni.Przylgnia grzybka zaworowego współpracuje z przylgnią gniazda zaworowego tworząc cykliczny szczelny kontakt stykowy w trakcie pracy silnika....
-
Cytocompatibility, antibacterial, and corrosion properties of chitosan/polymethacrylates and chitosan/poly(4‐vinylpyridine) smart coatings, electrophoretically deposited on nanosilver‐decorated titania nanotubes
PublicationThe development of novel implants subjected to surface modification to achieve high osteointegration properties at simultaneous antimicrobial activity is a highly current problem. This study involved different surface treatments of titanium surface, mainly by electrochemical oxidation to produce a nanotubular oxide layer (TNTs), a subsequent electrochemical reduction of silver nitrate and decoration of a nanotubular surface with...
-
Increasing efficiency of technological process by limiting impact of corrosive environment on operation of spiral classifiers
PublicationMost of the technological operations related to the preparation of the output to be enriched and to the production of the final copper concentrate take place with the use of water environment. Water management, besides using innovative technical and technological solutions, is a significant factor in the whole copper ore enrichment process. Mine water resources and surface water of the tailing pond named "Żelazny Most" are the...
-
An experimental study of self-sensing concrete enhanced with multi-wall carbon nanotubes in wedge splitting test and DIC
PublicationConcrete is the worldwide most utilized construction material because of its very good performance, forming ability, long-term durability, and low costs. Concrete is a brittle material prone to cracking. Extensive cracking may impact durability and performance over time considerably. The addition of a small amount of carbon nanotubes (CNT) increases the concrete’s overall electrical conductivity, enabling internal structure...
-
Aluminate Red Phosphor in Light-Emitting Diodes: Theoretical Calculations, Charge Varieties, and High-Pressure Luminescence Analysis
Publication