displaying 1000 best results Help
Search results for: HYBRID WAVES
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublicationThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Design solution and selected research results of the sea-wave energy converter
PublicationW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
Rectangular microstrip resonator illumi-nated by normal-incident plane wave
PublicationW pracy przedstawiono koncepcję modów oświetlających pozwalającą na obliczenie podstawowych parametrów elektrycznych anten mikropaskowych - częstotliwości rezonansowej, rezystancji promieniowania i charakterystyki promieniowania. Oparta jest ona na dwuwymiarowej metodzie przestrzeni widmowej, w której pobudzenie występuje w formie pojedynczej fali płaskiej padającej prostopadle na analizowaną strukturę. Rezultatem takiego podejścia...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Non-Wave Variations in Temperature Caused by Sound in a Chemically Reacting Gas
PublicationA weakly nonlinear generation of non-acoustic modes in the field of sound in a gas is considered. An exotericchemical reaction of A->B type, which takes place in a gas, may be reversible or not. Two types of sound areconsidered, low-frequency and high-frequency as compared with the characteristic time of a chemical reaction.For both these cases, the governing equations of non-acoustic modes are derived and conclusions of the efficiencyof...
-
On some properties of 2d spectral finite elements in problems of wave propagation
PublicationW pracy przedstawiono sformułowanie dwuwymiarowych elementów spektralnych stosowanych w symulacji propagacji fal prowadzonych. Zbadano własności tych elementów pod kątem występowania form pasożytniczych, odporności na dystorsję siatki oraz zbadano wpływ kształtu elementu na krzywe dyspersji
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Coherent-wave Monte Carlo method for simulating light propagation in tissue
PublicationSimulating propagation and scattering of coherent light in turbid media, such as biological tissues, is a complex problem. Numerical methods for solving Helmholtz or wave equation (e.g. finite-difference or finite-element methods) require large amount of computer memory and long computation time. This makes them impractical for simulating laser beam propagation into deep layers of tissue. Other group of methods, based on radiative...
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
Elastic wave propapagation in diagnostics of self-drilling system of grouted anchors
PublicationThe paper presents an experimental investigation of elastic wave propagation in a self-drilling hollow bar system, which is commonly used in geotechnical industry as the element of grouted ground anchors and soil nails. The single self-drilling hollow bar and self-drilling system of two bars connected by a coupler were considered. Longitudinal waves were excited at one end of the bar and registered at both ends, by means of PZT...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublicationWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Impact of radio wave polarisation on off-body communications in indoor environments
PublicationThis paper describes the measurements and the analysis of the impact of radio wave polarisation on off-body communications in Body Area Networks in indoor environments. Measurements on polarisation impact are briefly described. Five investigated scenarios with different body postures and different antenna placements are characterised. The difference between the vertical and horizontal components of the received radio signal are...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublicationThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Local dynamics of fluids and dielectrics as the foundation of signal-carrying wave properties
PublicationThis paper develops an original approach to fundamental problems of classical linear acoustics and electromagnetics, proving a crucial role of doubly-dynamic local properties of a propagation medium in supporting wave-like fields able to carry information signals. The proof is composed of two steps concerning, subsequently, fluid acoustics and dielectric electromagnetics. The first step consists in complementing a common, practically...
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublicationThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
A higher order shell element for wave propagation in isotropic shell structures
PublicationThe presents the new multi mode higher order shell element for wave propagation problems in shell structures.
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublicationThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublicationThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Radiation phenomena from metamaterial cylinders at oblique plane wave incidence.
PublicationW pracy przedstawiono wpływ ujemnej przenikalności elektrycznej i magnetycznej rezonatorów cylindrycznych umieszczonych w wolnej przestrzeni na parametry rozproszenia. Wykorzystano zmodyfikowaną procedurę iteracyjną i metodę dopasowania rodzajów w celu badania fali rozproszonej od układu cylindrów przy ukośnym padaniu fali płaskiej.
-
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Experimental an numerical investigation of wave propagation in composite beam with an additional mass
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacji numerycznych ilustrujace wpływ dodatkowej masy na propagacje fali Lamba w belce kompozytowej.
-
Electromagnetic wave scattering by a set of axially symmetric omega-medium cylinder
PublicationZaprezentowano analizę rozproszenia fali elektromagnetycznej od układu obiektów cylindrycznych zbudowanych z materiałów pseudochiralnych, umieszczonych w złączach falowodowych lub wolnej przestrzeni. Analiza bazuje na iteracyjnej procedurze rozproszenia i metodzie dopasowania rodzajów.
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
Publication -
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
PublicationThis paper describes an open and extensive validation study carried out by the Specialist Committee on Ships in Operation at Sea (SOS) of the International Towing Tank Conference (ITTC) on the newly developed SHOPERA-NTUA-NTU-MARIC (SNNM) wave-added resistance prediction method. The SNNM method aims at a simple, fast and transparent determination of the added resistance in regular waves of arbitrary encounter directions, even when...
-
A Comprehensive Survey on Antennas On-Chip Based on Metamaterial, Metasurface, and Substrate Integrated Waveguide Principles for Millimeter-Waves and Terahertz Integrated Circuits and Systems
PublicationAntennas on-chip are a particular type of radiating elements valued for their small footprint. They are most commonly integrated in circuit boards to electromagnetically interface free space, which is necessary for wireless communications. Antennas on-chip radiate and receive electromagnetic (EM) energy as any conventional antennas, but what distinguishes them is their miniaturized size. This means they can be integrated inside...
-
International Conference on Hybrid Intelligent Systems
Conferences -
Graffiti saves birds: A year-round pattern of bird collisions with glass bus shelters
Publication -
Global Value Chains and Wages: International Evidence from Linked Worker-Industry Data
PublicationUsing a rich dataset on over 110,000 workers from nine European countries and the USA we study the wage response to industry dependence on foreign value added. We estimate a Mincerian wage model augmented with an input-output interindustry linkages measure accounting for task heterogeneity across workers. Low and mediumeducated workers and those performing routine tasks experience (little) wage decline due to major dependency of...
-
Integrated sectors - diversified earnings: the (mising) impact of offshoring on wages and wage convergence in the EU27
PublicationThis paper assesses the impact of international outsourcing/offshoring practices on the process of wage equalization across manufacturing sectors in a sample of EU27 economies (1995–2009). We discriminate between heterogeneous wage effects on different skill categories of workers (low, medium and high skill). The main focus is on the labour market outcomes of vertical integration, so we augment a model of conditional wage convergence through...
-
Relationship between wages, labour productivity and unemployment rate in new EU member countries
PublicationThe main aim of this article is to find out the extent to which relative labour productivity and relative unemployment rate changes determine relative wage changes. We use average annual macro-data for the period 2002-2013 for Poland and other 5 new EU members: Estonia, Hungary, Slovak, Czech Republic and Slovenia. Using Poland as benchmark, rst we examine the correlation between wage, productivity and unemployment rate changes...
-
BIODIVERSITY OF YEASTS ISOLATED FROM CAVES OF THE POLISH TATRA MOUNTAINS, AND ITS BIOTECHNOLOGICAL POTENTIAL
PublicationMost of the Earth’s biosphere is permanently or periodically exposed to temperatures below 5°C. Cold habitats harbor a wide diversity of psychrophiles. For many years Antarctica has been the geographic area preferred for studying the diversity and properties of cold-adapted microorganisms. However, the non-Antarctic habitats like Himalayas or Alps are also extensively explored. The Tatra Mountains are Europe’s second-highest massif...
-
Integrated Sectors - Diversified Earnings: The (Missing) Impact of Offshoring on Wages and Wage Convergence in the EU27
PublicationThis paper assesses the impact of international outsourcing/offshoring practices on the process of wage equalization across manufacturing sectors in a sample of EU27 economies (1995-2009). We discriminate between heterogeneous wage effects on different skill categories of workers (low, medium and high skill). The main focus is on the labour market outcomes of vertical integration, so we augment a model of conditional wage convergence...
-
Hybrid Monte-Carlo simulations of fluorescence anisotropy decay in disordered two-component systems in the presence of forward and back energy transfer
PublicationW pracy przedstawiono hybrydowy algorytm symulacji Monte Carlo zaniku anizotropii emisji fluorescencji w układach dwuskładnikowych z uwzględnieniem prostego i powrotnego transferu energii. Poprawność nowego algorytmu symulacji Monte Carlo zweryfikowano poprzez porównanie z wynikami obliczeń teoretycznych otrzymanymi w ramach modelu SCDM i z wynikami standardowej symulacji Monte Carlo (algorytm 'step by step').
-
Hybrid Monte-Carlo simulations of fluorescence anisotropy decayin three-component donor-mediator-acceptor systems in the presenceof energy transfer
PublicationW pracy przedstawiono nowy hybrydowy algorytm symulacji Monte-Carlo układu trójskładnikowego donor-mediator-akceptor. Działanie algorytmu zilustrowano na przykładzie zaników anizotropii emisji fluorescencji powyższego układu. Porównano wyniki hybrydowej symulacji Monte-Carlo z wynikami klasycznej metody ''step by step''. Stwierdzono bardzo dobrą zgodność wyników obu symulacji, przy czym algorytm hybrydowy wymaga znacznie krótszego...
-
Ciprofloxacin – Modified Degradable Hybrid Polyurethane-Polylactide Porous Scaffolds Developed for Potential Use as an Antibacterial Scaffold for Regeneration of Skin
Publication -
Application of Generalized Regression Neural Network and Gaussian Process Regression for Modelling Hybrid Micro-Electric Discharge Machining: A Comparative Study
Publication -
Computer-Aided Diagnosis of COVID-19 from Chest X-ray Images Using Hybrid-Features and Random Forest Classifier
PublicationIn recent years, a lot of attention has been paid to using radiology imaging to automatically find COVID-19. (1) Background: There are now a number of computer-aided diagnostic schemes that help radiologists and doctors perform diagnostic COVID-19 tests quickly, accurately, and consistently. (2) Methods: Using chest X-ray images, this study proposed a cutting-edge scheme for the automatic recognition of COVID-19 and pneumonia....