Filters
total: 917
-
Catalog
Search results for: STEPPER MOTOR
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublicationThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublicationThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Properties of water in the region between a tubulin dimer and a single motor head of kinesin
PublicationA kinesin is a molecular motor that can perform movement on a microtubule track in a stepping-like manner. This motion is connected with processes of association and dissociation of kinesin and tubulin. Water is an important participant in these kinds of molecular interactions. This is why we have decided to investigate the dynamical and structural properties of water in the region between the kinesin catalytic domain and the tubulin...
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublicationIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublicationInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
Five-phase Induction Motor Drive Operation During Stator Phase Fault
PublicationThe article presents the most important advantages of multi-phase electric drives. The construction of a five-phase squirrel cage induction motor together with possible stator winding distribution cases is presented, which affect the properties of such motor. Increased reliability of five-phase drives was indicated. The drive operation properties were confirmed by experimental results.
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublicationThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
Multiscalar Control Based Airgap Flux Optimization of Induction Motor for Loss Minimization
PublicationBased on the induction motor model, considering the core loss resistance that accounts for magnetic characteristic saturation, a speed control approach is devised with an adaptive full-order (AFO) speed observer. The induction motor model analysis is done sincerely in a stationary reference frame. The control approach incorporates a flux reference generator designed to meet optimal operational circumstances and a nonlinear speed...
-
Application of neural networks for identification of forcedness having effect on magnitude of turbine rotor vibration using rotor trajectory.
PublicationW pracy dokonano analizy zastosowania sieci neuronowych do wyznaczenia wartości wymuszeń wpływających na wielkość drgań wirnika używając trajektorii jako parametr określający drgania. Badania przeprowadzono na powietrznej, jednostopniowej turbinie modelowej. Przemieszczenia poziome i pionowe wirnika turbiny mierzono przy pomocy systemu pomiarowego i rejestrowano na oscyloskopie cyfrowym. Przeprowadzono pomiary trajektorii ruchu...
-
Smartphone-based digital image colorimetry for the determination of total capsaicinoid content in chili pepper extracts
PublicationA simple smartphone-based digital image colorimetry was proposed for the determination of total capsaicinoid content and the assessment of chili pepper pungency. The biobased solvent D-limonene was used for the first time to isolate analytes. Capsaicinoids were efficiently separated from chili pepper by solid-liquid extraction with D-limonene followed by partitioning of the analytes into the ammonium hydroxide solution to eliminate...
-
PERCEPTUAL AND MOTOR SKILLS
Journals -
Jarosław Guziński prof. dr hab. inż.
PeopleJaroslaw Guzinski received M.Sc., Ph.D. and D.Sc. degrees from the Electrical Engineering Department at Technical University of Gdansk, Poland in 1994, 2000 and 2011 respectively. Since 2016 he is Associate Professor at Gdansk University of Technology. Currently he is the head of the Department of Electric Drives and Energy Conversion. From 2006 to 2009 he was involved in European Commission Project PREMAID Marie Curie, ‘Predictive...
-
Losses and power balance in hydraulic satellite motor supplied with oil and HFA-E emulsion
PublicationMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motor with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motor. The research of satellite motor has been conducted...
-
Novel adaptive flux observer for wide speed range sensorless control of induction motor
PublicationA new adaptive flux observer of induction motor is presented in the paper. The Lyapunov theory is utilized for derivation of the adaptation law of rotor flux angular speed, which acts as unknown parameter in an augmented induction motor model. In the field weakening region, where stray fluxes are comparable with rotor flux magnitude, the air-gap flux stabilization is proposed. An air-gap flux multiscalar model is derived for stator...
-
Theoretical and mathematical models of the torque of mechanical losses in a hydraulic rotational motor for hydrostatic drive
PublicationW pracy przedstawiono modele teoretyczne i matematyczne momentu strat mechanicznych występujących w silniku hydraulicznym obrotowym o stałej teoretycznej chłonności qMt silnika na obrót wału (o stałej teoretycznej objętości roboczej VMt silnika) i o zmiennej chłonności qMgv = bM qMt na obrót wału (o zmiennej geometrycznej objętości roboczej VMgv silnika). Modele mają służyć badaniom laboratoryjnym i symulacyjnym strat energetycznych...
-
Comparison of two methods for parameters selection of the proportional observer of induction motor state variables
PublicationArtykuł opisuje problemy odtwarzania prędkości obrotowej wału maszyny indukcyjnej przy wykorzystaniu estymatorów MRAS. Porównano dwie metody doboru wzmocnień obserwatora, analityczną i bazującą na algorytmach genetycznych
-
Control Systems of an Induction and Synchronous Motor Supplied by Current Source Converter Working as Generator
Publication -
Computational investigations of acoustic radiation from end shields of small-power electric motor
PublicationW artykule omówiono rozwój metod modelowania własności akustycznych maszyn elektrycznych. Wskazano na pomijalny dotąd, znaczący udział drgań tarcz łożyskowych w emitowaniu hałasu przez silniki małej mocy. Na podstawie równania falowego potencjału prędkości wyprowadzono analityczne formuły do obliczeń akustycznych w polu bliskim tarczy łożyskowej. Zamieszczono uzyskane z serii obliczeń dla pracującego silnika, rozkłady ciśnienia...
-
Review of Linear Electric Motor Hammers—An Energy-Saving and Eco-Friendly Solution in Industry
Publication -
Model-Free Controller Tuning Based on DFT Processing: Application to Induction Motor Drives
PublicationIn this paper, we present a new approach based on discrete Fourier transform (DFT) analysis for controller tuning of the closed-loop system with unknown plant. The DFT analysis is used to process the closed-loop measurements collected online to derive the frequency response of an initial closed-loop system that does not provide a good performance. Based on the closed-loop frequency response data, we propose two methods for tuning PID...
-
The influence of the motor filtrers on harmonic current emmision in the pro-ective connection of drive systems.
PublicationThis paper contains detailed analysis of currents in protective wire in engine supplied from frequency converter without any external filters added. It was found that the peak value of current in protective conductor of engine was about 1500 mA at frequencies 5 Hz 50 Hz. In the continuation of research the dU/dt type motor filter and the sinusoidal filter were tested. It was found that the current in protective wire decreased...
-
Nonlinear control of five phase induction motor with synchronized third harmonic flux injection
PublicationThe paper deals with the novel control system for five phase induction motor (IM) that enables the injection of the rotor flux 3rd harmonic component. Two multiscalar models are transformed from the 1-1 and 2-2 vector models developed in the 1st and 3rd harmonic planes. Based on the obtained multiscalar models the synthesis of dual multiscalar control is established. The obtained two multiscalar control systems can independently...
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublicationIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
The effect of the motor filters on earth fault current waveform in circuits with variable speed drives
PublicationIn circuits with variable speed drives distorted earth fault current flows. Earth fault current distortion influences the threshold of ventricular fibrillation. This paper presents earth fault current distortion in circuits with variable speed drives when motor filter is used. Two types of motor filter are analyzed. For every type of filter the effect of earth fault current distortion on ventricular fibrillation is evaluated.
-
The effect of the motor filters on earth fault current waveform in circuits with variable speed drives
PublicationIn circuits with variable speed drives distorted earth fault current flows. Earth fault current distortion influences the threshold of ventricular fibrillation. This paper presents earth fault current distortion in circuits with variable speed drives when motor filter is used. Two types of motor filter are analyzed. For every type of filter the effect of earth fault current distortion on ventricular fibrillation is evaluated.
-
The Adaptive Backstepping Control of Permanent Magnet Synchronous Motor Supplied by Current Source Inverter
Publication...
-
Weather Hazard Avoidance in Modeling Safety of Motor-Driven Ship for Multicriteria Weather Routing
PublicationWeather routing methods find the most suitable ocean?s route for a vessel, taking into account changeable weather conditions and navigational constraints. In the multicriteria approach based on the evolutionary SPEA algorithm one is able to consider a few constrained criteria simultaneously. The approach applied for a ship with hybrid propulsions has already been presented by one of the authors on previous TransNav?2009. This time...
-
The Influence of Water and Mineral Oil on Mechanical Losses in a Hydraulic Motor for Offshore and Marine Applications
PublicationIn this paper, mechanical losses in a hydraulic motor supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and compared. The experimental tests were onducted using a special design (prototype) of a hydraulic satellite motor. The design of the satellite motor is presented. This motor was developed to supply both with water and mineral oil and features...
-
Assembling and testing of quasi-static hybrid piezoelectric motor based on electroactive lubrication principle
PublicationThe presented paper concerns a novel concept of hybrid piezoelectric motor based on electroactive lubrication principle. Its structure is combined of quasi-static and resonance piezoelectric actuators, synchronizing their work to generate the rotary movement. The hybrid motor topology is compared to the existing piezoelectric motors, regarding its field of applications in embedded systems with very high security requirements. The...
-
Energy Loss Coefficients ki in a Displacement Pump and Hydraulic Motor used in Hydrostatic Drives
PublicationThe article aims at defining and analysing the energy loss coefficients in design solutions of rotating displacement machines, with a piston machine as an example. The energy losses observed in these machines include mechanical loss, volumetric loss, and pressure loss. The scale and relations between these losses in different machines depend on machine design and manufacturing quality, and on operating parameters. The operating...
-
The Methodology for Determining the Theoretical Based on the Characteristics of Effective Absorbency Versus Pressure Drop in the Motor
PublicationThis article describes a method for determining the theoretical and actual working volume of a hydraulic motor. It has been shown that the actual working volume of the motor is the sum of the theoretical working volume and the additional volume that depends on the pressure drop in the working chambers of the motor. It was also shown that the volumetric losses in the hydraulic motor are not only a function of the pressure drop in...
-
Rotor Blade Geometry Optimisation in Kaplan Turbine
PublicationThe paper presents the description of method and results of rotor blade shape optimisation. The rotor blading constitutes a part ofturbine flow path. Optimisation consists in selection of the shape that minimises ratio of polytrophic loss. Shape of the blade isdefined by the mean camber line and thickness of the airfoil. Thickness is distributed around the camber line based on the ratio ofdistribution. Global optimisation was done...
-
Variable Size Twin-Rotor Wind Turbine
Publication -
Bounds on the Cover Time of Parallel Rotor Walks
PublicationThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node maintains a cyclic ordering of its outgoing arcs, and successively propagates walkers which visit it along its outgoing arcs in...
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Diagnostics of commutation unit in satellite pumps and motors
PublicationThe article describes a part of the research on the development of satellite pumps and motors, conducted on Gdansk University of Technology as a part of grant "New elaborate of hydraulic satellite machines for drives with vegetable liquids and non-flammable liquids" (LIDER/35/102/L-2/10/NCBiR/2011) funded by the National Centre for Research and Development in Poland. The presented area includes the diagnostics of commutation units...
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Bounds on the cover time of parallel rotor walks
PublicationThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node successively propagates walkers visiting it along its outgoing arcs in round-robin fashion, according to a fixed ordering. We consider...
-
Dependence of Power Characteristics on Savonius Rotor Segmentation
PublicationSavonius rotors are large and heavy because they use drag force for propulsion. This leads to a larger investment in comparison to horizontal axis wind turbine (HAWT) rotors using lift forces. A simple construction of the Savonius rotor is preferred to reduce the production effort. Therefore, it is proposed here to use single-segment rotors of high elongation. Nevertheless, this rotor type must be compared with a multi-segment...
-
Diagnostics of commutation unit in satellite pumps and motors
PublicationThe article describes a part of the research on the development of satellite pumps and motors, conducted on Gdansk University of Technology as a part of grant "New elaborate of hydraulic satellite machines for drives with vegetable liquids and non-flammable liquids" (LIDER/35/102/L-2/10/NCBiR/2011) funded by the National Centre for Research and Development in Poland. The presented area includes the diagnostics of commutation units...
-
Artificial neural networks as a tool for selecting the parameters of prototypical under sleeper pads produced from recycled rubber granulate
Publication -
Application of Feedback Linearization for Air Gap Flux Control of Induction Motor in the Field Weakening Region
Publication -
Chapter 1 : Supply system influence on behaviour of an elektromechanical model - four bar/dc motor
PublicationPraca opisuje zagadnienia wspólnego modelowania układu wieloczłonowego i napędu elektrycznego. Analizowanym układem mechanicznym jest płaski czworobok przegubowy. Analizowany mechanizm zamodelowano jako układ wieloczłonowy z zamkniętymi wielobokami ciał. Do wymuszenia ruchu układu wykorzystano model silnika prądu stałego. Zaproponowano kilka alternatywnych sposobów zasilania silnika. Układem referencyjnym jest źródło prądu stałego....
-
Modelling of ic engine coolant system with permanent magnet brushless motor - bond graphs approach
PublicationW pierwszej części referatu przedstawiono strukturę i podstawy modelowania w ujęciu grafów wiązań nowoczesnego (nowej generacji) systemu chłodzenia silnika spalinowego. Istotną cechą rozważnego systemu chłodzenia jest zastosowanie zintegrowanego układu: pompa cieczy chłodzącej-bezszczotkowy silniki prądu stałego (BSPS, ang. BDCM). W kolejnych częściach referatu przedstawiono: podstawy modelowania całego systemu chłodzenia, model...
-
Modeling and simulation of a demonstration robot fed by a modular hybrid source with the dc brushless motor drive.
PublicationPrzedstawiono model demonstracyjnego robota mobilnego wykonany w środowisku Matlab-Simulink. Robot napędzany jest przez dwa silniki bezszczotkowe prądu stałego. Hybrydowe źródło energii składa się z wodorowego ogniwa paliwowego PEMFC oraz banku superkondensatorów. Wyniki symulacji przedstawiają zapotrzebowanie na moc podczas znormalizowanego cyklu jazdy robota oraz zachowanie układu w zależności od struktury hybrydowego źródła...
-
The importance of the shape of the protein–water interface of a kinesin motor domain for dynamics of the surface atoms of the protein
PublicationA single kinesin motor domain immersed in water has been investigated using molecular dynamics. It has been found that local properties of water in the solvation shell change along with the nature of the neighboring protein surface. However, a detailed analysis leads to the conclusion that the geometrical features of hydrogen bonds and overall structure of kinesin hydration water are not very different from bulk water. The local...
-
The importance of the shape of the protein-water interface of a kinesin motor domain for dynamics of the surface atoms of the protein
PublicationSingle kinesin motor domain immersed in water has been investigated using molecular dynamics. It has been found that local properties of water in solvation shell change along with the nature of neighboring protein surface. However, a detailed analysis leads to the conclusion that the geometrical features of hydrogen bonds and overall structure of kinesin hydration water is not very different from bulk water. The local values of...
-
Method of sum of power losses as a way for determining the ki coefficients of energy losses in hydraulic motor
PublicationThis paper shows application of the method of sum of power losses to determining energy losses which occur in hydraulic rotary motor in situation when not all laboratory data are at one’s disposal or when no use is made of data contained in catalogue charts. The method makes it possible to determine the coefficients ,ki , of energy losses occurring in the motor. The method of sum of power losses is based on the approach proposed...