displaying 1000 best results Help
Search results for: TILTED WALLS
-
A Self-Equalized Waveguide Filter With Frequency-Dependent (Resonant) Couplings
PublicationThis letter presents a design of a fifth-order linear phase filter with frequency-dependent couplings. The filter is composed of a triplet that is directly coupled to two resonators at the input and output. To provide group delay flattening a cross-coupling in the trisection has a strongly dispersive character with a negative slope parameter. To achieve this, an E-plane stub with a septum was used. To further improve the filter...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublicationTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
Diagnostics of bolted lap joint using guided wave propagation
PublicationThe paper presents numerical and experimental analyses of elastic waves propagation in a bolted lap joint. In experimental investigations condition assessment of the joint was performed with the use of symmetric waves excited by a piezoactuator. Numerical calculations were conducted in commercial finite element method software Abaqus. The influence of number of bolts and the value of the initial stress on recorded signals was examined....
-
Estimation of a Stochastic Burgers' Equation Using an Ensemble Kalman Filter
PublicationIn this work, we consider a difficult problem of state estimation of nonlinear stochastic partial differential equations (SPDE) based on uncertain measurements. The presented solution uses the method of lines (MoL), which allows us to discretize a stochastic partial differential equation in a spatial dimension and represent it as a system of coupled continuous-time ordinary stochastic differential equations (SDE). For such a system...
-
Sample Rate Conversion Based on Frequency Response Masking Filter
PublicationThe sample rate conversion with high resampling ratios requires low-pass digital filters with very narrow transition band which results in high computational complexity and makes filter design problematic. Therefore in this work we propose to use the FRM method, which breaks the filter with a narrow transition band into a group of filters with reduced design requirements. These decreases the number of non-zero coefficients and...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublicationIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Damage detection in a bolted lap joint using guided waves
PublicationThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
Sensorless Fault Detection of Induction Motor with Inverter Output Filter
PublicationThe paper presents the problem of monitoring and fault detection of a sensorless voltage inverter fed squirrel cage induction motor with LC filter. The detection is based on load torque estimation of the investigated torque transmission system. The load torque is calculated besides the computation of other variables that are mandatory for sensorless drive operation such as rotor flux and speed. The implemented LC filter smooths...
-
Concrete-filled FRP tubular members in marine and bridge structures
PublicationConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Sensorless predictive control of three-phase parallel active filter
PublicationThe paper presents the control system of parallel active power filter (APF) with predictive reference current calculation and model based predictive current control. The novel estimator and predictor of grid emf is proposed for AC voltage sensorless operation of APF, regardless of distortion of this voltage. Proposed control system provides control of APF current with high precision and dynamics limited only by filter circuit parameters....
-
Preload monitoring in a bolted joint using Lamb wave energy
PublicationThe knowledge of the load in prestressed bolted connections is essential for the proper operation and safety of engineering structures. Recently, bolted joints have become an area of intensive research associated with non-destructive diagnostics, in particular in the context of wave propagation techniques. In this paper, a novel procedure of bolt load estimation based on the energy of Lamb wave signals was proposed. Experimental...
-
Analog filter design system for field programmable analog array.
PublicationObiektowy system do automatycznego projektowania filtrów kaskadowych i symetrycznych filtrów FLF z wykorzystaniem wzmacniaczy transkonuktancyjnych OTACi bloków bikwadratowych z optymalizacją zakresu dynamiki, zniekształceń i wrażliwości. System umożliwia realizację standardowych aproksymacji charakterystyk amplitudowych oraz dowolnie zdefiniowanych przez użytkownika.
-
The Goertzel filter-bank usage in the non-stationary impedance measurement.
PublicationArtykuł prezentuje metodę pomiaru parametrów impedancyjnych w warunkach niestacjonarnych bazującą na próbkowaniu sygnałów pomiarowych i przetwarzaniu cyfrowym. Zaproponowano i przeanalizowano zastosowanie banku filtrów Goertzela. Porównano zaproponowane podejście z tradycyjnie stosowaną metodą STDFT. Przedstawiono wynik symulacji i pomiarów.
-
Seafloor backscattering: numerical simulation vs. filter theory approach.
PublicationPrzedstawiono model opisujący rozpraszanie sygnału akustycznego na nierównomiernej, regularnie sfalowanej powierzchni dna morskiego jako filtr liniowy z odpowiedzią impulsową o zmieniającej się w czasie chwilowej dominującej częstotliwości. Porównano przewidywania modelu z wynikami otrzymanymi w wyniku złożonych obliczeniowo symulacji numerycznych opartych na fizycznym modelu zjawiska wykorzystującym aproksymację Kirchhoffa. Wstępnie...
-
Output filter for voltage source inverter supplying induction motor
PublicationW artykule przedstawiono problemy związane z występowaniem składowej zerowej w falowniku napięcia. Jako rozwiązanie zastosowano filtr bierny składowej zerowej dodatkowo pełniący funkcję filtru sinusoidalnego. Filtr nie wprowadza zauważalnych przesunięć prądów i napięć na wejściu i wyjściu układu. Przedstawiono metodę doboru elementów filtru w prostokatnym układzie współrzędnych oraz wyniki badań symulacyjnych i eksperymentalnych....
-
Multivariate models of inter-resonator couplings for microwave filter synthesis
PublicationArtykuł przedstawia technikę budowy modeli częstotliwości rezonansowej, współczynnika sprzężenia między rezonatorami oraz sprzężenia ze źródłem/obciążeniem. Przedstawiony jest model siedmiu zmiennych uwzglęgniający topologię rezonatorów. Na podstawie modelu wykonana została synteza filtrów mikrofalowych.
-
Dynamic hand-written signature verification using a matched filter
PublicationW pracy zaproponowano nowe podejście do weryfikacji dynamicznego podpisu odręcznego. Podpis jest traktowany jako sygnał telekomunikacyjny, który można wykryć i zwerfikować za pomocą odbiornika optymalnego z filtrem dopasowanym. Wymaga to uprzedniej unifikacji i normalizacji parametrów biernych podpisu aktualnego, jak również podpisów zgromadzonych w bazie, celem ułatwienia podejmowania decyzji. Normalizację długości podpisu uzyskano...
-
Theoretical and numerical analysis of free vibration of liquid-filled tanks
PublicationW pracy rozpatrywano drgania giętne belki o stałym przekroju prostokątnym wypełnionej cieczą idealną. Częstości drgań własnych i formy drgań belki wyznacza się z nieskończonych układów równań algebraicznych (30) i (54). Rozwiązania przedstawiono na wykresach.
-
<title>Measurements of SIMCON 3.1 LLRF control signal processing quality for VUV free-electron laser FLASH</title>
Publication -
<title>Data transmission optical link for LLRF TESLA project part I: hardware structure of OPT0 module</title>
Publication -
<title>Decomposition of MATLAB script for FPGA implementation of real time simulation algorithms for LLRF system in European XFEL</title>
Publication -
<title>Cavity simulator and controller for VUV free electron laser SIMCON 2.1, part II: functional blocks</title>
Publication -
<title>SIMCON 3.0 eight channel FPGA-based cavity simulator and controller for VUV free-electron laser</title>
Publication -
Mittelalter (Parallel titles: Moyen Age - Medioevo)
Journals -
Misery on Main Street, victory on Wall Street: Economic discomfort and the cross-section of global stock returns
Publication -
Stability analysis of the internal cylindrical shell wall of a vertical double shell tank under a water test.
PublicationPrzedstawiono analizę zagrożenia stateczności lokalnej płaszcza wewnętrznego przy różnicy poziomów wody w zbiorniku wewnętrznym i przestrzeni międzypłaszczowej podczas próby wodnej zbiornika. Podano krytyczne różnice poziomów wody dla typowych zbiorników o pojemności od 10 000 do 100 000 m3.
-
Self-organising maps in the analysis of strains of human abdominal wall to identify areas of similar mechanical behaviour.
PublicationThe study refers to the application of a type of artificial neural network called the Self-Organising Map (SOM) for the identification of areas of the human abdominal wall that behave in a similar mechanical way. The research is based on data acquired during in vivo tests using the digital image correlation technique (DIC). The mechanical behaviour of the human abdominal wall is analysed during changing intra-abdominal pressure....
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated wall panels under edgewise compression
PublicationA composite structural insulated sandwich panel (CSIP) is a quite novel approach to the idea of sandwich structures. A series of natural-scale experimental test is required each time a change in panel’s geometry is planned and a reliable computational tool is required to precede actual laboratory testing with virtual simulations. An attempt of creating such a tool has been made with use of a commercial FEM code ABAQUS, in order...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublicationDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
Elimination of metal catalyst and carbon-like impurities from single-wall carbon nanotube raw material
Publication -
3D DEM simulations of monotonic interface behaviour between cohesionless sand and rigid wall of different roughness
PublicationArtykuł omawia wyniki metodą elementów dyskretnych (DEM) dotyczace zachowania się strefy kontaktu między bezkohezyjnym piaskiem a sztywną scianą o różnej szorstkości. Obliczenia wykonano dla dla różnej wysokości, nachylenia i rozstawu rowków wzdłuż sciany, które symulowały jej szorstkość. W symulacjach zmieniano dodatkowo ciśnienie pionowe i początkowy wskaźnik porowatosci piasku. Nacisk położono na wpływ szorstkości na mobilizowany...
-
Generating fractal tiles using Voronoi diagrams
PublicationPraca opisuje szczególną klasę podziałów powierzchni n-wymiarowego torusa na komórki o fraktalnym brzegu. Zbiór komórek przejawia nietypowe własności samopodobieństwa, może zostać użyty do wypełnienia przestrzeni R^n w sposób periodyczny lub aperiodyczny ze zmienną gęstością podziałów. Zaproponowany został algorytm do generowania takich podziałów używając diagramów Woronoja. Opisana metoda może mieć zastosowania w grafice komputerowej.
-
Organic filed effect transistor with zinc phthalocyanine.
PublicationW pracy przedstawiono wyniki badań doświadczalnych organicznego tranzystora polowego z warstwą ftalocyjaniny cynku. Jako podłoże zastosowano wysoko domieszkowane wafle krzemu pokryte warstwą tlenku krzemu (IV) o grubości 100 nm, na którą techniką fotolitograficzną była naniesiona struktura elektrod (tzw. geometria dolnych kontaktów). Złote elektrody źródła i drenu tworzyły kanał o długości 5 m (jest to odległość między elektrodą...
-
Selecting wells for an optimal design of groundwater monitoring network based on monitoring priority map: A Kish Island case study
PublicationThis paper presents a novel approach, i.e. a combination of gamma test and monitoring priority map, for optimal design of groundwater monitoring network (GMN) by considering the cumulative effects of industries, human activities, and natural factors on the groundwater quality. The proposed method was successfully applied to design an optimal network for groundwater salinity monitoring on Kish Island, Persian Gulf. The priority...
-
<title>Cavity simulator and controller for VUV free electron laser SIMCON 2.1, part I: algorithms and SIMCON system</title>
Publication -
<title>Manufacturing and measurements of triple-core, double-core, and twin-core single-mode soft-glass optical fibers</title>
Publication -
<title>Non-linear glasses and metaglasses for photonics, a review: Part II. Kerr nonlinearity and metaglasses of positive and negative refraction</title>
Publication -
Experimental tests results of the diode rectifier with series active power filter
Publication -
Performance evaluation of the parallel object tracking algorithm employing the particle filter
Publication -
Extracted window offsetting using maximally flat fractional delay filter
PublicationW pracy przedstawiono koncepcję projektowania filtru ułamkowoopóźniającego (FD) z wykorzystaniem metody okien offsetowanych. W zaproponowanym podejściu jako okna prototypowego, offsetowanego o opóźnienie ułamkowe projektowanego filtru, użyto okna wyodrębnionego z odpowiedzi impulsowej filtru optymalnego. Zaprojektowane w ten sposób filtry FD nie są optymalne jednak zapewniają lepszą jakość algorytmu zmiany szybkości próbkowania...
-
Electroconductivity and mechanical properties of carbon black Printex L6 filled polyurethanes
PublicationOpisano uzyskanie i badania kompozycji poliuretanowo-sadzowych na bazie sadzy przewodzącej Printex L6. Zaprezentowano wyniki badań nad wpływem udziału napełniacza przewodzącego na przewodnictwo elektryczne stałoprądowe i właściwości mechaniczne uzyskanych materiałów.
-
FPGA Implementation of the Gradient Adaptive Lattice Filter Structure for Feature Extraction
Publication -
Analysis of continuous-to-discrete transformation effect on a synthesis filter bank project
Publication -
Natural modes of an active slab microcavity with air-filled periodic inclusions
Publication -
Design of Microwave Lossy Filter Based on Substrate Integrated Waveguide (SIW)
PublicationIn this letter, we propose a lossy three-pole Chebyshev filter centered at 5.15 GHz, based on the substrate integrated waveguide (SIW) with scattering characteristics shifted down by 5.68 dB. The filter is composed of three directly coupled SIW cavities with three lossy couplings between nonadjacent resonators. These additional couplings are realized using mixed coupled slot and microstrip lines connected with metal electrode leadless...
-
An automated microwave planar filter design based on space mapping optimization
Publication -
Farrow structure implementation of fractional delay filter optimal in Chebyshev sense
PublicationW pracy omówiono problematykę implementacji filtrów ułamkowych opóźniających o zmiennym opóźnieniu w oparciu o strukturę Farrowa. Podejście to polega na obliczeniu próbek nowej odpowiedzi impulsowej filtru dla każdego wymaganego opóźnienia w opraciu o wielomiany o współczynnikach niezależnych od opóźnienia. Prowadzi to do znacznego zmniejszenia kosztów numerycznych implementacji w zastosowaniach wymagających częstej zmiany opóźnienia...
-
Porous Selective Laser Melted Ti and Ti6Al4V Materials for Medical Applications
Publication -
Comparison of Vacuum Sintered and Selective Laser Melted Steel AISI 316L
Publication -
Modelling and testing of a hydrodynamic clutch filled with electrorheological fluid in varying degree
Publication