Filters
total: 1734
displaying 1000 best results Help
Search results for: Ti13Nb13Zr alloy
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
X-ray Photoelectron Spectroscopy of Carboxylic Acids as Corrosion Inhibitors of Aluminium Alloys
PublicationThe datasets, titled X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media and X-ray Photoelectron Spectroscopy studies of various carboxylic acids adsorption on aluminium alloys in alkaline media, contain XPS studies of the corrosion inhibitory action of selected dicarboxylic acids towards commercially available aluminium alloy 5754 in alkaline media at pH=11. These datasets...
-
Thermoelectric properties of bismuth-antimony-telluride alloys obtained by reduction of oxide reagents
PublicationThe BieSbeTe alloys with different Bi/Sb/Te ratio were fabricated by an innovative method. For that purpose the oxide reagents were melted at high temperature, then quenched to form pellets, milled to a powder and finally reduced in hydrogen at various temperatures. Complex structures consisting of connected thin layers forming a continuous path between nano- and micrometer size grains have been obtained. The electrical conductivity,...
-
Comparison of corrosion resistance of al-alloys by means of dynamic electrochemical impedance spectroscopy
PublicationPrzeprowadzono badania metodą dynamicznej elektrochemicznej spektroskopii impedancyjne stopów 1100 i 5162. Zaproponowano zastępcze modele elektryczne opisujące zachowanie się stopów w warunkach ekspozycji w roztworach zawierających wysokie stężenie jonów chlorkowych. Wyznaczono zmiany podstawowych parametrów elektrycznych układów zastępczych od potencjału. Stwierdzono wyższą podatność na korozję stopu 5162 w porównaniu ze stopem...
-
Jacek Tomków dr hab. inż.
PeopleEducation:1. 2018 - Ph.D. of Technical Sciencesin field of Materials Engineeringthesis: Influence of underwater welding conditions on cold cracking of high strength low alloy steel 2. 2012 - Master of Science Engineer, Gdansk University of Technologyin the field of: Mechanical Engineeringwith specialization in: Manufacturing Engineering and Computer Aided Manufacturing Processesthesis: Non-destructive testing of welding joints...
-
Three-dimensional fractographic analysis of total fracture areas in 6082 aluminium alloy specimens under fatigue bending with controlled damage degree
Publication -
THE ANALYSIS OF THE INFLUENCE OF STRESS DISTRIBUTION ON WEAR PROFILE IN LUBRICATED SLIDING CONTACT OF UHMW-PE VS TITANIUM Ti-13Nb-13Zr ALLOY
PublicationMetal – polymer sliding contacts are a typical combination in industry and medicine. For decades such a set of materials has been the primary choice in human joints endoprosthetic technology. In this paper tribological issues of are presented from a research on the potential for practical use of Ti-13Nb-13Zr/UHMW-PE couple for orthopedic endoprosthesis. In tests on simplified models it is critically important to carefully...
-
Wpływ modyfikacji strontem na strukturę i własności mechaniczne stopu AlSi10Mg=Strontium modyfication influence on the microstructure and properties of AlSi10Mg alloy
PublicationPrzedstawiono wyniki badań materiałowych stopu odlewniczego AlSi10Mg przed i po modyfikacji strontem. Wykazano korzystne zmiany w strukturze i wzrost własności mechanicznych na skutek modyfikacji stopu.
-
Właściwości korozyjne stopu MM55 nadtopionego laserowo w warunkach kriogenicznych = Corrosion properties of the MM55 alloy laser melted at cryogenic conditions
PublicationStop MM55 stosowany do wyrobu śrub okrętowych poddano laserowemu nadtapianiu w warunkach kriogenicznych. W artykule przeprowadzono analizę mikrostruktury warstwy wierzchniej stopu MM55 po wymienionej obróbce cieplnej. Określono właściwości korozyjne wytworzonej warstwy wierzchniej nadtopionego stopu i porównano je ze stanem wyjściowym.
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublicationThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel Friction Stir Welding Methods
PublicationThe present study investigates the effect of two parameters of process type and tool offset on tensile, microhardness, and microstructure properties of AA6061-T6 aluminum alloy joints. Three methods of Friction Stir Welding (FSW), Advancing Parallel-Friction Stir Welding (AP-FSW), and Retreating Parallel-Friction Stir Welding (RP-FSW) were used. In addition, four modes of 0.5, 1, 1.5, and 2 mm of tool offset were used in two welding...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublicationA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Effect of cobalt addition on the corrosion behaviorof near equiatomic NiTi shape memory alloy in normal saline solution: electrochemical and XPS studies
PublicationThe electrochemical and corrosion (uniform and localized) behavior of a binary Ni52Ti48 shape memory alloy (SMA) and two ternary Ni52Ti48-xCox (x = 1.5 and 4.0 wt.%) SMAs were studied. Measurements were conducted in 0.9% NaCl solution at 37 oC employing various electrochemical methods. These include: linear polarization resistance (LPR), linear sweep voltammetry (LSV), chronoamperometry and dynamic electrochemical impedance spectroscopy...
-
Experimental investigations and damage growth modeling of EN‐AW 2024 aluminum alloy under LCF loading accounting creep pre‐deformation
PublicationThis article presents the results of experimental tests of creep rupture and of low-cycle fatigue (LCF) of EN-AW 2024 aluminum alloy devoid of damage and having preliminary damage. The preliminary damage was dealt in the process of creep at elevated temperature 100C, 200C, and 300C until achievement of two different strain values at each temperature. Samples with preliminary damage were subjected to fatigue tests at room temperature....
-
Effects of Micro-Arc Oxidation Process Parameters on Characteristics of Calcium-Phosphate Containing Oxide Layers on the Selective Laser Melted Ti13Zr13Nb Alloy
PublicationTitania-based films on selective laser melted Ti13Zr13Nb have been formed by micro-arc oxidation (MAO) at different process parameters (voltage, current, processing time) in order to evaluate the impact of MAO process parameters in calcium and phosphate (Ca + P) containing electrolyte on surface characteristic, early-stage bioactivity, nanomechanical properties, and adhesion between the oxide coatings and substrate. The surface...
-
Catalytic impact of alloyed Al on the corrosion behavior of Co50Ni23Ga26Al1.0 magnetic shape memory alloy and catalysis applications for efficient electrochemical H2 generation
PublicationThe electrochemical and corrosion behaviour of Co50Ni23Ga27-xAlx (x = 0 and 1.0 wt%) magnetic shape memory alloys (MSMAs) was studied in 0.5 M NaCl solutions using various electrochemical techniques. Results showed remarkable activation of the tested MSMA toward pitting corrosion upon alloying it with Al. XPS examination confirmed the activation influence of alloyed Al. It proved that the presence of Al in the alloy's matrix weakens...
-
Charakterystyka stopu Ł83 wytworzonego metodami odlewania i natryskiwania cieplnego = Characteristic of the Ł83 alloy fabricated by casting and thermal spraying methods
PublicationPrzedstawiono mikrostrukturę i twardość stopu łożyskowego Ł83 wytworzonego metodami natryskiwania cieplnego i odlewania odśrodkowego. W tym aspekcie dokonano analizy przydatności metody natryskiwania w produkcji łożysk ślizgowych.
-
Corrosion resistance evaluation of Al-based alloys by means of dynamic electrochemical impedance spectroscopy
PublicationW pracy przedstawiono wyniki badań stopów aluminium wykonane za pomocą dynamicznej elektrochemicznej spektroskopii. Na podstawie uzyskanych widm impedancyjnych zostały pokazane zmiany parametrów elektrycznego schematu zastępczego z potencjałem. Stwierdzono, że dodatek magnezu do badanego stopu obniża właściwości przeciwkorozyjne stopu.
-
Application and modelling of Shape-Memory Alloys for structural vibration control: State-of-the-art review
PublicationOne of the most essential components of structural design for civil engineers is to build a system that is resistant to environmental conditions such as harsh chemical environments, and catastrophic disasters like earthquakes and hurricanes. Under these circumstances and disturbances, conventional building materials such as steel and concrete may demonstrate inadequate performance in the form of corrosion, deterioration, oxidizing,...
-
Corrosion resistance evaluation of Al‐based alloys by means of dynamic electrochemical impedance spectroscopy
Publication -
Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys
Publication -
Chapter 14 : A new concept of highly porous bioactive titanium alloys with hydroxyapatite coatings
PublicationPrzedstawiono koncepcję biomateriału o wysokiej bioaktywności i odporności na korozję. Omówiono metody wytwarzania porowatych stopów tytanu, techniki utleniania, techniki nakładania porowatego hydroksyapatytu, nakładanie bioaktywnych polimerów, metody badan i modelowania struktur porowatych.
-
Characteristics of the (Mn-N-O-P) type layers created on the cast aluminium alloys
PublicationPrzedstawiono skład chemiczny i fazowy, a także właściwości korozyjne i tribologiczne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na odlewniczych stopach aluminium. Warstwy typu (Mn-N-O-P) wielokrotnie podnoszą zarówno właściwości tribologiczne jak i korozyjne odlewniczych stopów aluminium z krzemem.
-
Evaluation of the Microstructure and Magnetic Properties of Fe73Me5Y3B19 (Where Me = Ti or Nb) Amorphous Alloys
Publication -
The present state of requirements of international association of classification societies (IACS) for wrought aluminium alloys
PublicationW referacie przedstawiono aktualną sytuację w zakresie stopów aluminium z serii 5xxx i 6xxx do przeróbki plastycznej, ze szczególnym uwzględnieniem zmian w tym zakresie zapoczątkowanych przez unifikację wymagań w dokumentach nr 25 i 26 opublikowanychostatnio przez International Association of Classification Societies (IACS). Jednym z najważniejszych punktów w tych dokumentach jest wymaganie odnośnie przeprowadzania próby odporności...
-
Electrophoretically deposited titanium and its alloys in biomedical engineering: Recent progress and remaining challenges
PublicationOver the past decade, titanium implants have gained popularity as the number of performed implantation operations has significantly increased. There are a number of methods for modifying the surface of biomaterials, which are aimed at extending the life of titanium implants. The developments in this field in recent years have required a comprehensive discussion of all the properties of electrophoretically deposited coatings on...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublicationThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
The Influence of Microstructure on the Passive Layer Chemistry and Corrosion Resistance for Some Titanium-Based Alloys
PublicationThe effect of microstructure and chemistry on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys, was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublicationThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media
Open Research DataThis dataset contains the results of high-resolution XPS obtained during evaluation of high corrosion inhibition efficiency of citric acid towards aluminium alloy 5754 in bicarbonate buffer pH=11. The exposition duration of samples to electrolytic environment was 100 min. Each sample was exposed at different citric acid concentration ranging from 0...
-
Modyfikacja powierzchni stopu Ti16Al4V przez nadtapianie laserowe w niskich temperaturach = Surface modification of the Ti6A14V alloy by laser melting in low temperature
PublicationPrzedstawiono założenia projektu badawczego zmierzającego do modyfikacji powierzchniowej stopu Ti6Al4V i uzyskaniu lepszej odporności na zużycie ścierne, tribokorozję i zmęczenie korozyjne dzięki nadtopieniu powierzchni stopu laserem w warunkach kriogenicznych.
-
Notch fatigue analysis and life assessment using an energy field intensity approach in 7050-T6 aluminium alloy under bending-torsion loading
PublicationThis paper studies the fatigue crack initiation and fatigue crack propagation of notched cylindrical bars made of 7050-T6 aluminium alloy subjected to multiaxial bending-torsion loading. The sites of crack initiation and the angles of crack initiation were successfully predicted from the distribution of the first principal stress at the notch surface. Fatigue crack initiation lives were computed through the new concept of energy...
-
Correlation between partial inhibition of hydrogen evolution using thiourea and catalytic activity of AB5-type hydrogen storage alloy towards borohydride electrooxidation
PublicationDirect borohydride fuel cells (DBFCs) are devices which directly convert the chemical energy stored in the borohydride ion and oxidant into electrical energy as a result of redox reactions. Unfortunately, a significant amount of fuel is lost as a result of the undesirable hydrolysis reaction. The selection of an efficient borohydride hydrolysis inhibitor requires detailed knowledge regarding the interaction mechanism between the...
-
Wpływ procesów utleniania na budowę warstwy napawanej ze stopu kobaltu = Oxidation process influence on the morphology the cobalt alloy clad layer
PublicationWarstwę napawaną laserowo ze stopu kobaltu poddano utlenianiu w różnych warunkach. Na powierzchni otrzymano różniące się warstwy tlenków o zróżnicowanej morfologii. Brak było widocznych zmian w mikrostrukturze napoiny. Zbadano także wpływ utleniania na twardość warstwy.
-
The influence of microstructure on the corrosion resistance for some titanium-based alloys
Open Research DataThis dataset contains scanning electron microscopy (SEM) micrographs revealing the microstructure of some Ti-based alloys, namely: Ti-6Al-4V (file name: TiV), Ti-6Al-7Nb (file name: TiNb) and TC21 (file name: TiAlSnZrMoCrNbSi) alloys and their localized corrosion as a result of passive layer breakdown in a corrosive environment, ie. 0.9% NaCl solution...
-
The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes
PublicationAl-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the...
-
Micro Arc Oxidation of Mechanically Alloyed Binary Zn-1X (X = Mg or Sr) Alloys
Publication -
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublicationPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions
PublicationInstantaneous impedance changes of 6060 and 6082 type aluminum alloys in pure water, and simulated acid rain poured into the pure water was investigated by dynamic electrochemical impedance spectroscopy (DEIS). In this way, the influence of aluminum content on the corrosion behavior of 6060 and 6082 type aluminum alloys immersed in simulated acid rain was determined. The corrosion rate of the alloy decreased with increasing Al...
-
Durability evaluation of Ni‐Cr‐Mo super alloys in a simulated scrubbed flue gas environment
Publication -
Evaluation of drawability of tailor-welded blanks made of titanium alloys Grade 2 || Grade 5
Publication -
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublicationA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
Social media as an opportunity or a blind alley in social communication and forest education? – Experiences from Poland
PublicationThe article characterizes the experiences, problems, and prospects for the development of forest education on social media, which in Poland has been carried out by the Państwowe Gospodarstwo Leśne Lasy Państwowe (National Forest Holding ‘State...
-
Microstructure and corrosion properties of the (Mn-N-O-P) type layers created on aluminium alloys
PublicationPrzedstawiono mikrostrukturę i właściwości korozyjne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na stopach aluminium. Wykazano, iż warstwy (Mn-N-O-P) podwyższają wielokrotnie odporność korozyjną stopów aluminium i mogą być stosowane jako warstwy ochronne na tych materiałach.
-
Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect
Publication -
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublicationThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Reinforced aluminium reference measurement R63 – earlier tests
Open Research DataPreliminary testing of aluminium alloys against 100Cr6 steel ball. Preparation to tests on wear of Al6061 alloy in ball on disk experiment. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Reinforced aluminium reference measurement Result1 – earlier tests
Open Research DataPreliminary testing of aluminium alloys against 100Cr6 steel ball. Preparation to tests on wear of Al6061 alloy in ball on disk experiment. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublicationThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...