Search
displaying 1000 best results Help
Search results for: millimeter waves
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Local dynamics of fluids and dielectrics as the foundation of signal-carrying wave properties
PublicationThis paper develops an original approach to fundamental problems of classical linear acoustics and electromagnetics, proving a crucial role of doubly-dynamic local properties of a propagation medium in supporting wave-like fields able to carry information signals. The proof is composed of two steps concerning, subsequently, fluid acoustics and dielectric electromagnetics. The first step consists in complementing a common, practically...
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublicationThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublicationThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Design solution and selected research results of the sea-wave energy converter
PublicationW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
A higher order shell element for wave propagation in isotropic shell structures
PublicationThe presents the new multi mode higher order shell element for wave propagation problems in shell structures.
-
On some properties of 2d spectral finite elements in problems of wave propagation
PublicationW pracy przedstawiono sformułowanie dwuwymiarowych elementów spektralnych stosowanych w symulacji propagacji fal prowadzonych. Zbadano własności tych elementów pod kątem występowania form pasożytniczych, odporności na dystorsję siatki oraz zbadano wpływ kształtu elementu na krzywe dyspersji
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublicationWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Rectangular microstrip resonator illumi-nated by normal-incident plane wave
PublicationW pracy przedstawiono koncepcję modów oświetlających pozwalającą na obliczenie podstawowych parametrów elektrycznych anten mikropaskowych - częstotliwości rezonansowej, rezystancji promieniowania i charakterystyki promieniowania. Oparta jest ona na dwuwymiarowej metodzie przestrzeni widmowej, w której pobudzenie występuje w formie pojedynczej fali płaskiej padającej prostopadle na analizowaną strukturę. Rezultatem takiego podejścia...
-
Electromagnetic wave scattering from material objects using hybrid methods
PublicationRozdział zawiera opis hybrydowych metod analizy stanowiących połączenie metody różnic skończonych w dziedzinie częstotliwości (FDFD) z metodą dopasowania rodzajów (MM), służących do badania cylindrycznych struktur falowych w układach zamkniętych i otwartych.
-
Non-Wave Variations in Temperature Caused by Sound in a Chemically Reacting Gas
PublicationA weakly nonlinear generation of non-acoustic modes in the field of sound in a gas is considered. An exotericchemical reaction of A->B type, which takes place in a gas, may be reversible or not. Two types of sound areconsidered, low-frequency and high-frequency as compared with the characteristic time of a chemical reaction.For both these cases, the governing equations of non-acoustic modes are derived and conclusions of the efficiencyof...
-
Basic ideas and advantages of the method of analytical regularization in wave optics: Overview
Publication -
Analysis of longitudinal wave propagation in a cracked rod by the spectral element method
Publication -
On the design of planar high directivity proximity couplers in the mm-wave range
PublicationPrzedyskutowano problemy projektowania sprzęgaczy zbliżeniowych wykonywanych w technologii planarnej i przeznaczonych do pracy w zakresie fal milimetrowych. Zasadniczym celem badań było zaprojektowanie, wykonanie i przebadanie układu sprzęgacza o wysokiej kierunkowości i umiarkowanym poziomie sprzężenia pracującego w zakresie 40-50GHz. Przedyskutowano i zamodelowano różne konfiguracje sprzęgaczy. Stwierdzono, że znane zasady projektowania...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublicationThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublicationThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublicationThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Coherent-wave Monte Carlo method for simulating light propagation in tissue
PublicationSimulating propagation and scattering of coherent light in turbid media, such as biological tissues, is a complex problem. Numerical methods for solving Helmholtz or wave equation (e.g. finite-difference or finite-element methods) require large amount of computer memory and long computation time. This makes them impractical for simulating laser beam propagation into deep layers of tissue. Other group of methods, based on radiative...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Elastic wave propapagation in diagnostics of self-drilling system of grouted anchors
PublicationThe paper presents an experimental investigation of elastic wave propagation in a self-drilling hollow bar system, which is commonly used in geotechnical industry as the element of grouted ground anchors and soil nails. The single self-drilling hollow bar and self-drilling system of two bars connected by a coupler were considered. Longitudinal waves were excited at one end of the bar and registered at both ends, by means of PZT...
-
An Efficient PEEC-Based Method for Full-Wave Analysis of Microstrip Structures
PublicationThis article introduces an efficient method for the equivalent circuit characterization and full-wave analysis of microstrip structures, leveraging the full-wave partial element equivalent circuit (PEEC). In particular, the multilayered Green's function is evaluated using the discrete complex-image method (DCIM) and employed to establish the mixed potential integral equations. The proposed strategy considers time delays for the...
-
Radiation phenomena from metamaterial cylinders at oblique plane wave incidence.
PublicationW pracy przedstawiono wpływ ujemnej przenikalności elektrycznej i magnetycznej rezonatorów cylindrycznych umieszczonych w wolnej przestrzeni na parametry rozproszenia. Wykorzystano zmodyfikowaną procedurę iteracyjną i metodę dopasowania rodzajów w celu badania fali rozproszonej od układu cylindrów przy ukośnym padaniu fali płaskiej.
-
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Experimental an numerical investigation of wave propagation in composite beam with an additional mass
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacji numerycznych ilustrujace wpływ dodatkowej masy na propagacje fali Lamba w belce kompozytowej.
-
Electromagnetic wave scattering by a set of axially symmetric omega-medium cylinder
PublicationZaprezentowano analizę rozproszenia fali elektromagnetycznej od układu obiektów cylindrycznych zbudowanych z materiałów pseudochiralnych, umieszczonych w złączach falowodowych lub wolnej przestrzeni. Analiza bazuje na iteracyjnej procedurze rozproszenia i metodzie dopasowania rodzajów.
-
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
Publication -
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
PublicationThis paper describes an open and extensive validation study carried out by the Specialist Committee on Ships in Operation at Sea (SOS) of the International Towing Tank Conference (ITTC) on the newly developed SHOPERA-NTUA-NTU-MARIC (SNNM) wave-added resistance prediction method. The SNNM method aims at a simple, fast and transparent determination of the added resistance in regular waves of arbitrary encounter directions, even when...
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Measurements of ultrasonic bulk and guided wave propagation in additively manufactured cubes and plates obtained by ultrasonic pulse velocity analyzer and scanning laser vibrometry
Open Research DataThe DataSet contains the results of measurements of ultrasonic wave propagation in additively manufactured samples made of polylactic acid (PLA). Three types of raster angles in two consecutive layers were assumed: 0°/90° (#1), 45°/-45° (#2) and 90°/90° (#3) with respect to the x-axis. For each printing variants a cubic sample (#C1-3) with dimensions...
-
Graffiti saves birds: A year-round pattern of bird collisions with glass bus shelters
Publication -
Relationship between wages, labour productivity and unemployment rate in new EU member countries
PublicationThe main aim of this article is to find out the extent to which relative labour productivity and relative unemployment rate changes determine relative wage changes. We use average annual macro-data for the period 2002-2013 for Poland and other 5 new EU members: Estonia, Hungary, Slovak, Czech Republic and Slovenia. Using Poland as benchmark, rst we examine the correlation between wage, productivity and unemployment rate changes...
-
Integrated Sectors - Diversified Earnings: The (Missing) Impact of Offshoring on Wages and Wage Convergence in the EU27
PublicationThis paper assesses the impact of international outsourcing/offshoring practices on the process of wage equalization across manufacturing sectors in a sample of EU27 economies (1995-2009). We discriminate between heterogeneous wage effects on different skill categories of workers (low, medium and high skill). The main focus is on the labour market outcomes of vertical integration, so we augment a model of conditional wage convergence...
-
BIODIVERSITY OF YEASTS ISOLATED FROM CAVES OF THE POLISH TATRA MOUNTAINS, AND ITS BIOTECHNOLOGICAL POTENTIAL
PublicationMost of the Earth’s biosphere is permanently or periodically exposed to temperatures below 5°C. Cold habitats harbor a wide diversity of psychrophiles. For many years Antarctica has been the geographic area preferred for studying the diversity and properties of cold-adapted microorganisms. However, the non-Antarctic habitats like Himalayas or Alps are also extensively explored. The Tatra Mountains are Europe’s second-highest massif...
-
Integrated sectors - diversified earnings: the (mising) impact of offshoring on wages and wage convergence in the EU27
PublicationThis paper assesses the impact of international outsourcing/offshoring practices on the process of wage equalization across manufacturing sectors in a sample of EU27 economies (1995–2009). We discriminate between heterogeneous wage effects on different skill categories of workers (low, medium and high skill). The main focus is on the labour market outcomes of vertical integration, so we augment a model of conditional wage convergence through...
-
Global Value Chains and Wages: International Evidence from Linked Worker-Industry Data
PublicationUsing a rich dataset on over 110,000 workers from nine European countries and the USA we study the wage response to industry dependence on foreign value added. We estimate a Mincerian wage model augmented with an input-output interindustry linkages measure accounting for task heterogeneity across workers. Low and mediumeducated workers and those performing routine tasks experience (little) wage decline due to major dependency of...
-
Antimicrobial Activities of Compounds Produced by Newly Isolated Streptomyces Strains from Mountain Caves
Publication -
Design and Optimization of Metamaterial-Based Dual-Band 28/38 GHz 5G MIMO Antenna with Modified Ground for Isolation and Bandwidth Improvement
PublicationThis letter presents a high-isolation dual-band multiple-input multiple-output (MIMO) antenna based on the ground plane modification and optimized metamaterials (MMs) for 5G millimeter-wave applications. The antenna is a monopole providing a dual-band response at 5G 28/38 bands with a small physical size (4.8 × 2.9 × 0.762 mm3, excluding the feeding line). The MIMO consists of two symmetric radiating elements arranged adjacently...
-
Low-Cost 3-D Printed Lens Antenna for Ka-Band Connectivity Applications
PublicationThis paper discusses the use of low-cost 3-D printing technology to fabricate dielectric lenses for Ka-band wireless networks. A low-cost FDM alternative to previously presented 3-D printed lens in SLA technology with high performance resin is presented. The presented approach has been demonstrated for a 39 GHz MU-MIMO antenna array modified to realize multibeam or switched-beam antenna that can support demanding energy-efficient...