Search
Search results for: RESONANT TRANSDUCER
-
A new prototype of piezoelectric bending resonant transducer for analysis of soft tissues properties
PublicationThis paper is devoted to a new piezoelectric bending resonant transducer prototype dedicated to the characterization of the mechanical properties of soft tissue. A general description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing version. Constitutive equations are presented for the active and passive layer...
-
An experimental study on transducer for the dds technology demonstrator
PublicationPrzedmiotem artykułu jest cylindryczny wieloelementowy przetwornik ultradźwiękowy wykonany w technologii DDS - demonstratora. Opisane zostały własności szerokopasmowego promieniowania przetwornika którego elementy zostały wykonane z piezokompozytowego materiału. W artykule zamieszczono wyniki badań wycinka próbnego - wykonanego z trzech elementów piezokompozytowych.
-
Measuring the impedance of ultrasonic transducers.
PublicationW przypadku przetworników ultradźwiękowych charakteryzujących się zazwyczaj bardzo zmienną w funkcji częstotliwości impedancją jej pomiar stwarza szereg trudności. Nie nadają się do tego celu tanie, łatwo dostępne, przyrządy. Znane są drogie systemy badawcze stosowane do tego celu. Zazwyczaj przystosowane są one do takich pomiarów w szerokim paśmie częstotliwości, od pasma akustycznego aż do zakresu mikrofalowego. Natomiast,...
-
Estimation of the uncertainty of the AC/AC transducer output voltage
PublicationThe paper presents a methodology for estimating uncertainty of voltage transducers processing function, on the example of CYVS411D07 voltage transducers. The analysis was conducted using the method based on the GUM Guide propagation of uncertainty law and the determination of the coverage factor based on the effective number of degrees of freedom (t-Student distribution). The paper also presents example evaluation results of measured...
-
Fibre Bragg Grating pressure transducer using a profiled membrane.
PublicationW pracy przedstawiono nowatorską konstrukcję podwodnego światłowodowego przetwornika ciśnienia, w którym elementem czujnikowym jest światłowodowa siatka Bragga. W omawianym przetworniku siatka Bragga jest zapisana w światłowodzie domieszkowanym pierwiastkami ziem rzadkich i pracuje jako pompowany optycznie laser z rozłożonym sprzężeniem zwrotnym. Dzięki zastosowaniu profilowanej membrany uzyskuje się jednorodny rozkład naprężeń...
-
Comprehensive modeling of interferometric hydrophone with self-supported mandrel transducer.
PublicationW pracy przedstawiono wyniki modelowania nowego typu samonośnego przetwornika dla interferometrycznego hydrofonu światłowodowego. Zaprezentowano wyniki analizy statycznej, modowej i dynamicznej przeprowadzonej przy pomocy Metody Elementów Skończonych. W modelowaniu wykorzyastano techniki opracowane dla laminatów, co pozwoliło na uzyskanie dokładnych wyników przy względnie krótkim czasie obliczeń.
-
Numerical modeling of sound intensity distributions around acoustic transducer
PublicationThe aim of this research study is to measure, simulate and compare sound intensity distribution generated by the acoustic transducers of the loudspeaker. The comparison of the gathered data allows for validating the numerical model of the acoustic radiation. An accurate model of a sound source is necessary in mathematical modeling of the sound field distribution near the scattering obstacles. An example of such obstacle is a human...
-
Badania eksperymentalne rezonansowego przetwornika piezoelektrycznego typu "unimorph"
PublicationW artykule opisano badania eksperymentalne piezoelektrycznego rezonansowego przetwornika zastosowanego do pomiaru właściwości mechanicznych tkanek miękkich. Po krótkim wstępie w kolejnych punktach przedstawiono opis stanowiska pomiarowego oraz metody pomiaru odkształceń prototypów, przesunięć częstotliwości rezonansowej, impedancji elektromechanicznej i parametrów schematów zastępczych. W dalszej...
-
A simulation investigation into the signal reconstruction accuracy of the transducer with pulse frequency output
Publication -
Piezoelectric Transducer for Mechanical Assessment of Soft Tissues. Concept, Implementation and Analysis
PublicationThe main goal of this work was following: preparation of a new concept, implementation and analysis of the piezoelectric resonant sensor/actuator for measuring the aging process of human skin. The research work has been carried out in the framework of cooperation between the INP-ENSEEIHT-LAPLACE, Toulouse, France, and at the Gdansk University of Technology, Faculty of Electrical and Control Engineering, Research Group of...
-
A tool for designing water tanks for measuring hydroacoustic transducers
PublicationSpecial water tanks are commonly used to measure the parameters of underwater acoustic systems. They must meet specific requirements, the fulfilment of which ensures very small but acceptable measurement errors. These requirements define the size of the tank and its shape as well as the strong attenuation of reflected waves. At the design stage, it is necessary to determine the impact of the tank structure on the measurement errors...
-
Determinig the impedance of ultrasonic transducers by the added elements method
PublicationPomiar zespolonej impedancji elektrycznej przetworników ultradźwiękowych jest obarczony szeregiem trudności. Wynika to między innymi z powodu iż charakteryzuje się ona dużymi zmianami wartości w funkcji częstotliwości - w szczególności w otoczeniu rezonansów. Szczególne trudności nastręcza tu pomiar fazy. Zastosowanie precyzyjnych mostków wiąże się z bardzo uciążliwym procesem pomiarowym i długim czasem jego trwania. Współczesne...
-
Modeling of selected transducer designs for optical pressure sensors using polarization interferometry
PublicationW artykule przedstawiono wyniki modelowania metodą Elementów Skończonych wybranych konstrukcji membran do zastosowań w interferometrycznych czujnikach ciśnienia. Omówiono zależność prametrów membran od kształtu membrany, jej wymiarów i zastosowanego materiału. Zakres odkształcen badanych membran jest niezbyt duży, co może pogarszać dokładność pomiaru czujników ciśnienia, w których będą one stosowane Omówiono kierunki dalszych...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
The use of a static electrical energy meter as a transducer of active power to a pulse frequency signal
Publication -
Resonant Conditions in a Node with an SVC Compensator
PublicationThe primary purpose of installing static shunt compensators in power grids is to improve the voltage conditions. Additional reactive power sources increase the system’s voltage stability and enable faster system recovery after a voltage failure. This paper presents the impact of an SVC device’s structure and settings on impedance change in the supply system, and hence on the frequencies at which resonance phenomena can develop.
-
MAGNETIC RESONANCE IN CHEMISTRY
Journals -
Estimation of the uncertainty of the LEM CV 3-500 transducers processing function
PublicationThe paper presents the methodology for estimating uncertainty of a voltage transducer processing function based on the example of LEM CV 3-500 transducer. The analysis was performed using the method based on the GUM Guide propagation of uncertainty law and the Monte Carlo numerical method. The article also presents a comparative analysis of the results of a voltage measurement evaluation done using the Monte Carlo simulation method,...
-
Remote Health Monitoring of Wind Turbines Employing Vibroacoustic Transducers and Autoencoders
PublicationImplementation of remote monitoring technology for real wind turbine structures designed to detect potential sources of failure is described. An innovative multi-axis contactless acoustic sensor measuring acoustic intensity as well as previously known accelerometers were used for this purpose. Signal processing methods were proposed, including feature extraction and data analysis. Two strategies were examined: Mel Frequency Cepstral...
-
Software-based method of increasing the effective resolution of a measurement chain for a transducer with a pulse frequency output
Publication -
Modal FEM Analysis of Ferrite Resonant Structures
PublicationThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
Development and Assessment of Regeneration Methods for Peptide-Based QCM Biosensors in VOCs Analysis Applications
PublicationCleaning a quartz crystal microbalance (QCM) plays a crucial role in the regeneration of its biosensors for reuse. Imprecise removal of a receptor layer from a transducer’s surface can lead to unsteady operation during measurements. This article compares three approaches to regeneration of the piezoelectric transducers using the electrochemical, oxygen plasma and Piranha solution methods. Optimization of the cleaning method allowed...
-
A LUMPED-CIRCUIT MODEL OF CIRCULAR PISTON TRANSDUCER FOR MODELING ITS PERFORMANCE IN DUAL FREQUENCY OPERATING MODES
PublicationThe paper presents novel network equivalent circuit of piezoceramic circular disc transducer that takes into account thickness and ra dial mode of vibrations. The starting point of the analysis is 4-port description of circular disc element representing the solution of wave equation set in radial and thickness directions. Th e approximate solution for harmonic case is represented in the form of 4x4 matrix, which is syn thesized...
-
Electro-optical transducer based on indium-tin-oxide-coated optical fiber for analysis of ionized media
PublicationThe paper introduces a concept of an optical fiber based electro-optical transducer for monitoring of ionized media, such as low-temperature plasma. It utilizes optical fiber with a section of a core coated with tailored indium tin oxide (ITO) thin film and thus combines the optical phenomena of lossy-mode resonance (LMR) with the electrostatic probe. ITO is an optically transparent and electrically conductive material and if its...
-
A Numerical Study on Baseline-Free Damage Detection Using Frequency Steerable Acoustic Transducers
PublicationIn structural health monitoring (SHM) a considerable amount of damage detection algorithms based on guided waves (GW) have been developed. Most of them rely on extensive transducer networks, besides preliminary reference measurements of the structures. This originated a growing demand for hardware simplification and cost reduction of the wave-based SHM methods, driving the conception of new solutions enabling both: the reduction...
-
Resonant ultrasonic spectroscopy in high-voltage varistor spectroscopy
PublicationResonant spectroscopy is an effective non-destructive testing method focused on defects in tested objects. The testing procedure, based on the resonant pattern, allows rejection of the tested samples with defects which do not fit the pattern. A sweeping frequency method has been used to measure the spectrum of resonances in high-voltage varistors. As a result we can observe resonances that depend directly on inhomogeneity of the...
-
Comments on unified analysis of switched-capacitor resonant converters
PublicationW pracy przedyskutowano możliwości regulacji napięcia wyjściowego w powielaczu typu c-przełączane, wpływ na sprawność energetyczną, użycie dodatkowych induktorów.
-
Resonant and nonresonant excitation of waves in a planar magnetosonic flow
PublicationForced propagation of perturbations in a magnetosonic wave are considered. The driving force may be caused by stimulated Mandelstam–Brillouin scattering of optic waves or by intense magnetosonic exciter. Some heating-cooling function which takes into account radiative cooling and unspecified heating is taken into consideration, as well as nonlinearity of a medium. Both these factors make the excitation particular. The analytical...
-
Planar Microwave Bragg Reflector Resonant Dielectric Sensor
PublicationIn this paper, a periodic structure is used to design a microwave Bragg reflector with the help of hexagonal lattice, which provides a 5 GHz wide stopband between the low-pass band with cut-off frequency 2.6 GHz and the bandpass response with start and stop frequency 7.8 GHz and 10.5 GHz, respectively. A defect in lattice allows passing a narrowband signal at 6 GHz which is found, from the dispersion relation, to be in the region...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublicationThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Accurate modeling of quasi-resonant inverter fed IM drive
PublicationIn this paper wide-band modeling methodology of a parallel quasi-resonant dc link inverter (PQRDCLI) fed induction machine (IM) is presented. The modeling objective is early-design stage prediction of conductive electromagnetic interference (EMI) emissions of the considered converter fed IM drive system. Operation principles of the selected topology of PQRDCLI feeding IM drive are given. Modeling of the converter drive system is...
-
A Self-Equalized Waveguide Filter With Frequency-Dependent (Resonant) Couplings
PublicationThis letter presents a design of a fifth-order linear phase filter with frequency-dependent couplings. The filter is composed of a triplet that is directly coupled to two resonators at the input and output. To provide group delay flattening a cross-coupling in the trisection has a strongly dispersive character with a negative slope parameter. To achieve this, an E-plane stub with a septum was used. To further improve the filter...
-
Slow-wave fractal-shaped compact microstrip resonant cell
PublicationA novel fractal-shaped compact microstrip resonant cell (CMRC) featuring a strong slow-wave effect has been presented. Its vital usefulness in the process of microstrip line miniaturisation has been proved and experimentally validated on the basis of a compact 3-dB branch-line coupler illustrating the possibilities of the approach. A prototype example structure has been designed to mirror the characteristics of a conventional device,...
-
Research and Development of Inductive-Resonant Wireless Power Transfer System
Publication -
Carboxylation Enhances Fragmentation of Furan upon Resonant Electron Attachment
PublicationWe report a dissociative electron attachment study to 2-furoic acid (C5H4O3) isolated in a gas phase, which is a model molecule consisting of a carboxylic group and a furan ring. Dissociation of furan by low energy electrons is accessible only via electronic excited Feshbach resonances at energies of incident electrons above 5 eV. On the other hand, carboxylic acids are well- known to dissociate via attachment of electrons at subexcitation energies....
-
Quality assessment of varistor ZnO structures by resonant ultrasound spectroscopy
PublicationWarystory sa wytwarzane z tlenku cynku ZnO jako cylindrycznie uformowane struktury, a ich jakość zależy od zmieniających się uwarunkowań technologicznych na etapach formowania ich kształtu oraz spiekania. W związku z tym są one testowane w końcowej fazie produkcji, a elementy wadliwe się odrzuca. Proponujemy testowanie jakości struktur ZnO we wcześniejszej fazie ich wytwarzania w celu wyeliminowania elementów wadliwych z dalszej,...
-
Resonant Frequencies in the Open Microstrip Structures Placed on Curved Surfaces
PublicationThe paper presents the research on open microstrip structures placed on curved surfaces such as cylindrical, elliptical or spherical. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields into suitable function series. Utilizing the continuity conditions the boundary problem is formulated which is solved with the use of method of moments. The investigated structures find application...
-
Magnetic Resonance
Journals -
Stochastic resonance in measurements
PublicationNoise is usually associated with the negative phenomenon, hampering the measurements data and their analysis. This view has been broken in the '80s when the phenomenon of stochastic resonance (Stochastic Resonance - SR) was discovered. It is a phenomenon that occurs in nonlinear dynamic measurement systems when the selected input noise can optimize system performance. SR became a way to improve efficiency of weak signals detection....
-
The effect of circular saw blade clamping diameter on its resonant frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with the...
-
Diagnostics of high-voltage varistor quality using resonant ultrasound spectroscopy
PublicationResonant spectroscopy is an effective nondestructive testing method focused on defects detection in tested objects. Resonance spectrum contains an information about the mechanical properties and particularly about the structural homogeneity of the whole object. A swept frequency method has been used to measure the selected resonant frequencies range. The system for measurement of resonant ultrasound spectroscopy of high-voltage...
-
Quasi-resonant dc-link inverter with a reduced number of active elements
PublicationW artykule przedstawiono nową topologię równoległego quasi-rezonansowego obwodu pośredniczącego falownika napięcia. Opisano sekwencje miękkiej komutacji falownika w dwukierunkowym trybie pracy falowniczej i prostowniczej. Analiza układu została zweryfikowana badaniami symulacyjnymi i eksperymentalnymi. Przedstawiona topologia odznacza się prostą strukturą oraz małą ilością elementów aktywnych. Dzięki zastosowaniu krzepkiej strategii...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublicationThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...
-
Slow-wave resonant structures in branch-line coupler miniaturization: a case study
PublicationA case study of novel slow-wave resonant structures dedicated to efficient microstrip branch-line coupler size reduction has been presented. A compact 3-dB branch-line coupler has been designed to mimic the performance of its conventional counterpart, simultaneously demonstrating a substantial 88% surface area reduction. The vital usefulness of the approach in the process of microstrip line abbreviation has been experimentally...
-
Novel topology of compact coplanar waveguide resonant cell low-pass filter
PublicationIn this study, a novel pseudoelliptic function low-pass filter (LPF) constituted by a compact coplanar waveguide resonant cell has been designed and manufactured. The lumped-element seven-pole prototype has been adequately realized by using complementary perturbations located both in signal line and ground plane metallization. The fabricated uniplanar LPF offers a compact size of 5.6 x 9.8 mm2, return loss better than 26 dB over...
-
A predictive estimation based control strategy for a quasi-resonant dc-link inverter
PublicationIn this paper the predictive estimation based control strategy for a quasi-resonant dc link inverter (PQRDCLI) is developed. Instead of direct measurement of dc link input inverter current – its estimation with one step prediction is applied. The PQRDCLI fed induction motor, controlled with a predictive current estimation stabilized inverter output voltage slopes independently of load. Moreover, reduction of overvoltage spikes...
-
Efficient calculation of the resonant frequencies of a SIW resonator with FDFD-based macromodel algorithm
PublicationW pracy przedstawiono efektywną metodę do analizy struktur ze integrowanym podłożem (SIW). W celu szybkiego obliczenia częstotliwości rezonansowych używany jest algorytm FDFD z zaimplementowanymi makromodelami.
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublicationIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
Non-isolated resonant quasi-Z-source network DC–DC converter
PublicationA novel non-isolated resonant quasi-impedance (quasi-Z)-source network DC–DC converter is proposed. The resonant impedance source network is derived from the quasi-Z-source network by including the autotransformer-based resonant cell instead of the second inductor of the quasi-Z-network. The leakage inductance of the autotransformer and two resonant capacitors connected in series with the autotransformer windings constitute a high-frequency...