Publications
Filters
total: 851
Catalog Publications
Year 2016
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublicationIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Interfacial adhesion evaluation in (low-density polyethylene)/elastomer blends
PublicationLow-density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co-rotating twin-screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (KalarVR ), and styrenebutadiene- rubber block copolymer (SBS; KratonVR ). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on...
-
Investigating the combined impact of plasticizer and shear force on the efficiency of low temperature reclaiming of ground tire rubber (GTR)
PublicationIn the present work, ground tire rubber (GTR) was mechano-chemically reclaimed at ambient temperature using two-roll mills. Road bitumen and styrene-butadiene-styrene (SBS)-modified bitumen at variable content (in range: 2.5–20 phr) were applied as reactive plasticizers to enhance reclaiming of GTR. For better understanding the plasticizing effect of bitumen on the quality of obtained reclaimed rubber, mechano-chemically reclaimed...
-
Microstructure, mechanical properties, and flame retardancy of nanoclay-incorporated polyurethane flexible foam composites
PublicationThe present work seeks to investigate microstructure, mechanical properties, and flame retardancy of polyurethane/nanoclay flexible foam composites. In this regard, we prepared various nanocomposites with and without nanoclay and observed the resulting morphologies to correlate them with the other corresponding characteristics. The results provided support for the fact that tensile strength and compression set will increase with...
-
Microwave assisted liquefaction with crude glycerol as a potential method of brewer's spent grain utylization
PublicationBrewer's spent grain was applied as a low-cost industrial type of lignocellulose biomass in a liquefaction and solvent: biomass ratio on the efficiency of the process, chemical structure and basic properties of obtained prepared polyols and soil residues shed light on the biomass degradation mechanism through application of microwaves and further reaction of degradation products with solvent particles.
-
Modification of microporous polyurethane elastomers with different types of ash—morphological, mechanical, and thermal studies
PublicationIncorporation of wood ash particles from wood gasification into microporous polyurethane elastomers has been investigated and compared to addition of commercially available microspheres resulting from coal burning. Samples were modified with 3 and 6 wt% of fillers. Structure, mechanical, and thermal properties of obtained elastomers were investigated. Incorporation of both types of ash particles decreased the density of polyurethanes...
-
Morfologia, właściwości mechaniczne oraz palność spienionych materiałów poliuretanowo-poliglicerynowych modyfikowanych grafitem ekspandowanym
PublicationSpienione kompozyty poliuretanowo-glicerynowe modyfikowane grafitem ekspandowanymotrzymano metodą jednostopniową z układu dwukomponentowego, gdzie jako składnik poliolowyzastosowano odpadową poliglicerynę. Scharakteryzowano morfologię, właściwościmechaniczne oraz klasę palności otrzymanych materiałów. Uzyskane wyniki wskazują, żewprowadzenie poligliceryny do matrycy poliuretanowej umożliwia otrzymanie materiałówcharakteryzujących...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublicationThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
Polyurethane Nanocomposites Containing Reduced Graphene Oxide, FTIR, Raman, and XRD Studies
PublicationRecently, graphene and other graphene-based materials have become an essential part of composite science and technology. Their unique properties are not only restricted to graphene but also shared with derivative compounds like graphene oxide, reduced graphene oxide, functionalized graphene, and so forth. One of the most structurally important materials, graphene oxide (GO), is prepared by the oxidation of graphite. Though removal...
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublicationThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Processing and structure–property relationships of natural rubber/wheat bran biocomposites
PublicationIn this work, wheat bran was used as cellulosic filler in biocomposites based on natural rubber. The impact of wheat bran content [ranging from 10 to 50 parts per hundred rubber (phr)] on processing, structure, dynamic mechanical properties, thermal properties, physico-mechanical properties and morphology of resulting biocomposites was investigated. For better characterization of interfacial interactions between natural rubber...
-
Progress in non-isocyanate polyurethanes synthesized from cyclic carbonate intermediates and di- or polyamines in the context of structure–properties relationship and from an environmental point of view
PublicationCommercially, polyurethanes are produced by the reaction of diisocyanates, polyols (polyester or polyether) and low molecular weight chain extender. Toxicity, moisture sensitivity and phosgene-based synthesis of diisocyanates resulted in investigations focused on obtaining the non-isocyanate polyurethanes (NIPUs). This work presents the review of synthesis and structure–properties relationship of non-isocyanate polyurethanes obtained...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublicationIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
Single-phase product obtained via crude glycerine depolymerisation of polyurethane elastomer: structure characterisation and rheological behaviour
PublicationPolyurethane recycling is a topic of growing interest due to the increasing amount of polyurethanewaste. The main purpose of polyurethane feedstock recycling is to recover the starting polyol, a valuable material. In thiswork, amethod of polyurethane thermo-chemical recycling, glycerolysisbymeansof crude glycerine, is proposed. Themaineffort is focusedonthe employment of crude glycerine without purification from biodiesel production...
-
Standarycja i certyfikacja degradacji środowiskowej tworzyw sztucznych, cz II
PublicationRozkład tworzyw sztucznych w środowisku jest złożonym procesem, którego przebieg w dużym stopniu zależy od rodzaju tworzywa sztucznego, jak również od warunków, na które tworzywo jest narażone. W niniejszej pracy przedstawiono usystematyzowany, aktualny stan szybko rosnących zasobów normatywnych w zakresie biodegradacji. Opracowanie to powstało na podstawie analizy danych różnych organów normalizacyjnych takich jak: Amerykańskie...
-
Standaryzacja i certyfikacja degradacji środowiskowej tworzyw sztucznych
PublicationDegradujące w środowisku naturalnym produkty z tworzyw sztucznych są grupą materiałów polimerowych, których ilość znacznie wzrosła w ostatnich latach. Ustanowiono wiele testów degradacji środowiskowej przez różne jednostki normalizacyjne. Testy te są również wykorzystywane, przy ustalaniu podstawowych systemów certyfikacji. Standardowe testy określają na przykład, jak pomiary biodegradacji danego materiału muszą być wykonane lub...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Synthesis and characterisation of polyurethane elastomers with semi-products obtained from polyurethane recycling
PublicationIn this work polyurethane elastomers were synthesised by using different mixtures of a petrochemical and glycerolysate polyols and 4,4-diphenylmethane diisocyanate (MDI). Glycerolysate polyol was produced from polyurethane foam decomposition using crude glycerine as a decomposition agent. The structure and thermal properties of obtained semi-product were similar to the polyol used in the synthesis of original foam. Glycerolysate...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublicationNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
Synthesis, Structure and Properties of Poly(ester-Urethane-Urea)s Synthesized Using Biobased Diamine
PublicationModern polymer science and technology is focused on the development of partial or fully green polymers. This focus is related to green chemistry trends, which propose using natural and renewable resources as monomers in the synthesis of polymers. In this study, biobased diamine was used as a chain extender of ester-urethane prepolymer. Obtained poly(ester-urethane-urea) contains 16 wt% of biobased diamine. There is mention of an...
-
Synthesis, structure and properties of poly(ether-urethane)s synthesized using a tri-functional oxypropylated glycerol as a polyol
PublicationThe main aim of this work was to obtain poly(ether-urethane)s using tri-functional polyoxyalkylene polyol (Rokopol G1000), which introducing the chemical cross-links into the structure of polyurethanes. Poly(ether-urethane)s were prepared using two-step method, called prepolymer method, which involves in the first step the reaction of 4,4'-diphenylmethane diisocyanate (MDI) and tri-functional polypropylene glycol glycerol triether...
-
The estimation of total volatile organic compounds emissions generated from peroxide cured natural rubber/polycaprolactone blends
PublicationNatural rubber (NR)/polycaprolactone (PCL) blends at the ratio of 90/10% wt. (NR/PCL90/10) and 70/30% wt. (NR/PCL70/30), with a constant amount of dicumyl peroxide, were prepared by compounding in an internal mixer. Obtained NR/PCL bio-based blends were cured at three different temperatures (150 °C, 160 °C and 170 °C). The total content of volatile organic compounds (TVOC) as a function of the NR/PCL blends ratio, and their curing...
-
Thermal and Mechanical Properties of Microporous Polyurethanes Modified with Reduced Graphene Oxide
PublicationMicroporous polyurethanes (MPU) were modified by adding 0.25%–1.25 wt% of reduced graphene oxide (RGO). The materials were prepared without solvent via in situ polymerization. From a technological point of view, it is very important to obtain functional materials by using reacting compounds only. The thermal characteristics of obtained MPU were investigated using TGA, DSC, and DMA techniques. In comparison to nonmodified microporous...
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublicationThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
Thermoplastic elastomer filaments and their application In 3D printig
PublicationThe paper provides an overview on the materials used in the 3D printing technology (the Polish and foreign market) with a particular focus on flexible filaments and their possible application in the industry. There are described the techniques of 3D printing and modern filaments available on the market. There is observed the increase of interest in the production of products from filaments based on thermoplastic elastomers (TPE),...
-
Weldability of pipe grade polyethylenes as realized from thermal and mechanical properties assessments
PublicationSince polyethylene (PE) has been widely accepted for the production of high-pressure fluid conveying pipelines, studies devoted to weldability of PE connections were always of major importance. In this study, two industrial PE grades designed for pipe production, namely PE80 and PE100, were injection molded, cut, and then welded as PE100-PE100, PE100-PE80, and PE80-PE80. The heat-welded joints were assessed by differential scanning...
-
Wpływ temperatury na efektywność termomechanicznej regeneracji odpadów gumowych
PublicationTermo-mechaniczną regenerację miału gumowego w zmiennych warunkach temperaturowych prowadzono przy użyciu współbieżnej wytłaczarki dwuślimakowej. Następnie otrzymane regeneraty gumowe mieszano z zespołem sieciującym i wulkanizowano. Scharakteryzowano właściwości przetwórcze oraz mechaniczne regeneratów gumowych w funkcji temperatury ich wytwarzania.
-
Zbadanie struktury i wybranych własności elementów wykonanych z ABS i ABS/PC oraz ustalenie przyczyn występowania wad powierzchniowych na tych elementach
PublicationPrzebadano próbki wykonane z ABS oraz PC/ABS. Zakres przeprowadzonych badań i analiz obejmował: (1) Spektroskopię w podczerwieni z transformacją Fouriera (FTIR), (2) Różnicową Kalorymetrię Skaningową (DSC), (3) Analizę Termograwimetryczną (TGA), (4) Masowy i Objętościowy Wskaźnik Szybkości Płynięcia (MFR i MVR), (5) Twardość metodą Shore’a D oraz (6) wizytę w zakładzie produkcyjnym i analizę procesów montażowych.
Year 2015
-
A review: Fabrication of porous polyurethane scaffolds
PublicationThe aim of tissue engineering is the fabrication of three-dimensional scaffolds that can be used for the reconstruction and regeneration of damaged or deformed tissues and organs. A wide variety of techniques have been developed to create either fibrous or porous scaffolds from polymers, metals, composite materials and ceramics. However, the most promising materials are biodegradable polymers due to their comprehensive mechanical...
-
Application of Bladder Acellular Matrix in Urinary Bladder Regeneration: The State of the Art and Future Directions
PublicationConstruction of the urinary bladder de novo using tissue engineering technologies is the “holy grail” of reconstructive urology. The search for the ideal biomaterial for urinary bladder reconstruction has been ongoing for decades. One of the most promising biomaterials for this purpose seems to be bladder acellular matrix (BAM). In this review we determine the most important factors, which may affect biological and physical properties...
-
Bacterial cellulose in the field of wound healing and regenerative medicine of skin: recent trends and future prospectives
PublicationIn this overview, we focused on the bacterial cellulose (BC) applications, described in recently published scientific papers, in the field of skin regenerative medicine and wound care industry. Bacterial cellulose was proven to be biocompatible with living tissues. Moreover, its mechanical properties and porous structure are considered to be suitable for biomedical applications. It is due to the fact that porous structure of bacterial...
-
Badania dotyczące ustalenia poziomu polipropylenu i polietylenu w mieszaninie polimerowej - Raport z badań zleconych - Numer umowy: 031664
PublicationBadanie składu chemicznego (metodą FTIR oraz metodą rozpuszczania na gorąco w ksylenie), własności termicznych (metodą DSC) oraz stabilności termicznej (metodą TGA) mieszaniny polimerowej złożonej głównie z wtórnego polietylenu i polipropylenu
-
Charakterystyka faz rozdmuchu preform z poli(tereftalanu etylenu) w procesie rozdmuchiwania z jednoczesnym ich rozciąganiem
PublicationScharakteryzowano proces wytwarzania pojemników PET w procesie rozdmuchiwania z jednoczesnym rozciąganiem półfabrykatów w postaci preform. Największy nacisk położono na szczegółowe omówienie poszczególnych etapów procesu rozdmuchiwania oraz etapów pracy maszyny rozdmuchowej. Omówiono też wybrane zagadnienia przepływu powietrza podczas procesu rozdmuchiwania butelek. Poruszono również problem przemian fazowych tworzywa PET występujących...
-
Charakterystyka właściwości kompozytów termoplastycznych napełnianych miałem gumowym
PublicationKompozyty termoplastyczne napełniane miałem gumowym otrzymano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Scharakteryzowano właściwości mechaniczne oraz morfologię badanych kompozytów. Uzyskane wyniki wskazują że kompozyty typu termoplast/miał gumowy stanowią proekologiczną formę recyklingu zużytych opon samochodowych stanowiąc tym samym ciekawą alternatywę dla powszechnie stosowanego odzysku energetycznego.
-
Chemical identification of rubber fender sample and hardness and density measurements
PublicationScope of testing: Chemical identification of rubber fender sample and hardness and density measurements. - Raport z badań zleconych - Numer umowy: 031178
-
Chemical structure, thermal and mechanical characterization of bio-based polyurethane composites filled with microcrystalline cellulose
PublicationOver the past several decades, the interest in replacing the synthetic components used in the production of polymers and composites with their natural counteparts has been growing. Biocomposites belong to the group of materials produced with the use of renewable raw materials. There has been a recent surge of interest in the industrial applications of composites containing natural fibres reinforced with biopolymers. Biopolymers...
-
Chromatografia gazowa jako skuteczne narzędzie kontroli procesu wytłaczania
PublicationPraca stanowi literaturowy przegląd możliwości wykorzystania chromatografii gazowej (GC) jako narzędzia kontroli procesu wytłaczania materiałów polimerowych. Przedstawiono charakterystykę techniki GC oraz możliwości, jakie niesie ze sobą kontrola fazy gazowej uwalnianej podczas przetwórstwa materiałów polimerowych. Na podstawie dotychczas opublikowanych prac badawczych omówiono techniki i metody wykorzystywane do izolacji lotnych...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublicationGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
Degradibility in vitro of polyurethanes based on synthetic atactic poly[)R,S)-3-hydroxybutyrate
PublicationThe aim of the paper was to determine the degradibility of aliphatic polyurethanes in hydrolytic and oxidative solutions. DSC, GPC, density, polymer surface morphology were studied.
-
Determination of Hydroxy Groups in the Modified Epoxy Oligomers Using IR-Spectroscopy
PublicationThe use of IR-spectroscopy has been proposed to determine the content of hydroxy groups in the modified functional oligomers based on bisphenol A diglycidyl ether. Apart from hydroxy groups the investigated oligomers contain epoxy or peroxy, carboxy or acrylic groups.
-
Effect of ground tire rubber on structural, mechanical and thermal properties of flexible polyurethane foams
PublicationFlexible polyurethane foams were modified with two kinds of ground tire rubber, untreated and thermo-mechanically reclaimed. A reclamation process was performed in auto-thermal conditions, which reduced the cost of the process and decreased the environmental impact of devulcanization (e.g., emission of gases). The reclamation process was carried out in a continuous manner using a co-rotating twin screw extruder. The foams were...
-
Effect of kenaf fibre modification on morphology and mechanical properties of thermoplastic polyurethane materials
PublicationThe presented study examined the morphology and mechanical properties of biocomposites obtained from kenaf natural fibre and thermoplastic polyurethane. Kenaf was modified using various methods, namely: acetylation, blocked isocyanate, maleic anhydride and permanganate treatment. Those methods and ways of carrying out of surface modifications were not studied before on kenaf/thermoplastic polyurethane composites. Different fibre...
-
Effect of starch fillers on the dynamic mechanical properties of rubber biocomposite materials
PublicationIn the paper the results of dynamic mechanical study of the biocomposites containing one of two types of (potato or corn) strach used as fillers in different amount were discussed. The composites were obtained from rubbery mixture containing natural rubber (NR) as a main component. Thermomechanical analyses (by DMA) showed that the used quantity of strach fillers only slightly influence on the glass transition temperature of vulcanizates.
-
Ekologiczne pianki poliuretanowe otrzymane z surowców odnawianych
PublicationPrzedmiotem pracy była charakterystyka ekologicznych, sztywnych pianek poliuretanowych otrzymanych z biopoliolu uzyskanego w wyniku upłynniania biomasy celulozowej frakcją glicerynową. Sztywne pianki otrzymano metodą jednoetapową z układu dwukomponentowego przy stosunku grup NCO do OH wynoszącym 2:1. Udział biopoliolu w stosunku do zawartości komercyjnego poliolu wynosił odpowiednio 25, 50, 75 oraz 100 % mas. Otrzymane układy scharakteryzowano...
-
Ekspertyza uzupełniająca opinię biegłego sądowego dotyczącą powodu występowania wycieku uszczelniacza butylowego do wnętrza pakietu okiennego
PublicationW niniejszym dokumencie ekspertyzę uzupełniającą opinię biegłego sądowego dotyczącą powodu występowania wycieku uszczelniacza butylowego do wnętrza pakietu okiennego. Wyniki przeprowadzonych badań wskazują, iż Silikon o nazwie handlowej “Bosman” dostarczony od strony pozwanej nie jest identyczny pod względem chemicznym niż ten stosowany przez powoda. Silikon stosowany przez powoda rozmiękcza uszczelniacz butylowy stosowany w...
-
Fabrication of polyurethane and polyurethane based composite fibers by the electrospinning technique for soft tissue engineering of cardiovascular system
PublicationElectrospinning is the unique technique, which provides forming of polymeric scaffolds for soft tissue engineering, which include tissue scaffolds for soft tissues of cardiovascular system. Such artificial soft tissues of cardiovascular system may possess mechanical properties comparable to native vascular tissues. Electrospinning technique gives the opportu nity to form fibres with nm- to μm-scale in diameter. The arrangement...
-
Interfacially modified LDPE/GTR composites with non-polar elastomers: From microstructure to macro-behavior
PublicationThis paper provides some new insights into the mechanism of interaction and modifications in thermoplastic composites based on low density polyethylene (LDPE), ground tire rubber (GTR) and non-polar elastomer. The composites were prepared using a co-rotating twin-screw extruder at variable LDPE/GTR ratio and constant elastomer content. Two types of commercial elastomer were applied: styrene-butadiene-styrene (SBS) block copolymers (Kraton®)...
-
Investigation of volatile low molecular weight compounds formed during continuous reclaiming of ground tire rubber
PublicationGround tire rubber was thermo-mechanically reclaimed at different temperature conditions (80, 120, 160 °C) using a co-rotating twin screw extruder. The progress of ground tire rubber reclaiming was evaluated with specific mechanical energy, sol fraction and thermogravimetric analysis. Volatile organic compounds (VOCs) including volatile sulfur compounds (VCSs) released from ground tire rubber and ground tire rubber after reclaiming...
-
Kontrola jakości materiałów polimerowych wytwarzanych metodą wytłaczania: stan obecny i perspektywy rozwoju
PublicationNiniejsza praca stanowi przegląd literaturowy metod kontroli jakości materiałów polimerowych wytwarzanych metodą wytłaczania. Scharakteryzowano możliwości kontroli efektywności procesu wytłaczania działających w układach "on-line" oraz "in-line", które polegają na przeprowadzeniu pomiarów w czasie trwania procesu. Opisano potencjał aplikacyjny technik spektroskopowych (IR, UV-VIS), pomiarów właściwości reologicznych, analizy morfologii...
-
l-ascorbic acid modified poly(ester urethane)s as a suitable candidates for soft tissue engineering applications
PublicationIn this paper we created novel poly(ester urethane)s (PESUs) designed specifically for tissue engineering. The PESUs were derived from oligomeric α,ω-dihydroxy(ethylene-butylene adipate) (dHEBA), 1,4-butanediol (BDO) and aliphatic 1,6-hexamethylene diisocyanate (HDI) and modified with l-ascorbic acid to improve their biocompatibility. In addition, we determined their mechanical properties (such as tensile strength, elongation at...