Wyszukiwarka
Filtry
wszystkich: 61
wybranych: 57
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: FREE CONVECTION
-
Free Convection Heat Transfer from Horizontal Cylinders
PublikacjaThe results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations...
-
On the differential effect of temperature on the Nusselt-Rayleigh relationship in free convection
PublikacjaThe aim of and inspiration behind this paper was to explain the reasons, also observed by other researchers, of the discrepancy in the results of experimental free convection, which for small Rayleigh and Nusselt numbers in the initial phase of research can sometimes reach several hundred percent. These discrepancies decrease with increasing heating power and plate surface temperature, in proportion to the increase in Ra and Nu,...
-
Novel Analytic-Numerical Model of Free Convection: with Leading Edge Considered
PublikacjaA novel solution of the free convection boundary problem is represented in analytical form for velocity and temperature for an isothermal vertical plate, as an example. These fields are built as a Taylor Series in the x coordinate with coefficients as functions of the vertical coordinate (y). We restrict ourselves by cubic approximation for both functions. The basic Navier-Stokes and Fourier-Kirchhoff equations and boundary conditions...
-
Experimental investigation of free convection of glycol-Al2O3 nanofluid from horizontal tube
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublikacjaThe main aim of the present study was to investigate the influence of nanoparticles on heat transfer coefficients during free convection of water-Al2O3 nanofluid from horizontal porous coated tube under atmospheric pressure for nanoparticle concentration of 0.01% by weight. Contrary to published data present study concerns on free convection of nanofluids in extensive, quiescent fluid.
-
EXPERIMENTAL INVESTIGATION OF FREE CONVECTION OF GLYCOL-Al2O3 NANOFLUID FROM HORIZONTAL TUBE
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublikacjaNanofluids are expected to enhance heat transfer in many thermal systems. Present efforts are concentrated on boiling heat transfer of nanofluids, although single phase convection is of key importance in various appliances such as car radiators or heating systems. This paper presents experimental results of heat transfer during free convection of water-Al3O3 nanofluid from horizontal tube covered with metallic porous coating. Contrary...
-
The use of thermal imaging camera to estimate velocity profiles based on temperature distribution in a free convection boundary layer
PublikacjaThis work describes an attempt to assess whether the temperature field from a thermal imaging camera can be converted into a velocity field with an accuracy sufficient for qualitative conducting or describing the phenomenon, i.e. when the Navier-Stokes, Fourier-Kirchhoff and continuity equations are mutually coupled. The consequence of this link between temperature fields and velocity is the possibility to formulate the hypothesis...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
On analytical solution of stationary two dimensional boundary problem of natural convection
PublikacjaApproximate analytical solution of two dimensional problem for sta- tionary Navier-Stokes, continuity and Fourier-Kirchho equations describ- ing free convective heat transfer from isothermal surface of half innite vertical plate is presented. The problem formulation is based on the typ- ical for natural convection assumptions: the uid noncompressibility and Boussinesq approximation. We also assume that orthogonal to the plate component...
-
Theoretical consideration of free convective heat transfer from a round isothermal plate slightly inclined from the vertical
PublikacjaA semi-analytical solution of simplified Navier-Stokes and Fourier-Kirchhoff equations describing free convective heat transfer from a round isothermal surface slightly inclined from the vertical is presented. The solution is based on the assumption, typical for natural convection, that the velocity component normal to the surface is negligibly small in comparison to the tangential one. Next we neglect the nonlinear inertia force...
-
Possibility of thermal imaging use in studies of natural convection heat transfer on the example of an isothermal vertical plate.
PublikacjaA new method of infrared (IR) camera use in convective heat transfer studies has been presented. Until now, IR cameras were utilized for temperature field visualizations of flat heated surfaces of solid objects only. Because liquids and gasses do not emit radiation in the infrared range of wave lengths, detection of temperature field in the air was conducted with the use of plastic mesh, which, after heating by hot air, emits infrared...
-
Intensification of thermal convection near electric devices using flat screens – computer modelling
PublikacjaIntensification of natural thermal convection near electric devices is possible by application of additional elements as screens creating convection canals close to the device. In the earlier authors paper the results of the analysis of thermal convection with the use of only one additional screen close to the electric device were presented. This paper presents computer modelling of thermal convection when two screens near the...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublikacjaThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
The effect of dehydration/rehydration of bacterial nanocellulose on its tensile strength and physicochemical properties
PublikacjaBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of biomedical applications. BNC contains 99 % of water which makes it too thick to be used as a bioimplant material. The aim of the work was to determine the effect of the BNC dehydration followed by rehydration on its mechanical and physicochemical properties, in the context of the use of BNC as bio-prostheses in the cardiovascular system. Dehydration involved the...
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublikacjaThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Application of nanofluids in selected thermal technologies
PublikacjaSome peculiarities regarding convective heat transfer of nanofluids are presented. Particularly, results of the fundamental research concerning pool boiling and single phase convection of nanofluids as well as data obtained for selected heat exchangers operated with nanofluids are discussed.
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublikacjaThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Computational analysis of power-law fluids for convective heat transfer in permeable enclosures using Darcy effects
PublikacjaNatural convection is a complex environmental phenomenon that typically occurs in engineering settings in porous structures. Shear thinning or shear thickening fuids are characteristics of power-law fuids, which are non-Newtonian in nature and fnd wide-ranging uses in various industrial processes. Non-Newtonian fuid fow in porous media is a difcult problem with important consequences for energy systems and heat transfer. In this...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublikacjaThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
ATTEMPTS OF THERMAL IMAGING CAMERA USAGE IN ESTIMATIONS OF THE CONVECTIVE HEAT LOSS FROM A VERTICAL PLATE
PublikacjaIn this paper a new method for determining heat transfer coefficients using a gradient method has been developed. To verify accuracy of the proposed method vertical isothermal heating plate with natural convection mechanism has been examined. This configuration was deliberately chosen, because of the fact that such case is historically the earliest and most thoroughly studied and its rich scientific documentation - the most reliable....
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Effect of microwave and convection heating on selected nutrients of human milk
PublikacjaThe aim of this study was to determine the influence of the microwave heating method (MWH) on selected determinants of the nutritional value of human milk (HM) and compare to the effect exerted by the standard convection heating (CH) method, including holder pasteurization (HoP). It was showed that using MWH under conditions assumed to ensure microbiological safety, changes in the level of the nutrients were not observed. In these...
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublikacjaThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublikacjaThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
Effect of convection and microwave heating on the retention of bioactive components in human milk
PublikacjaBioactive substances are very important components of human milk (HM), especially for premature newborns. The effects of convection (CH) and microwave heating (MWH) at 62.5 and 66 °C, on the level of selected bioactive components of HM: lysozyme (LZ), lactoferrin (LF), secretory immunoglobulin A (sIgA), basal lipase (BL), cytokine TGF-2, vitamin C and total antioxidant capacity (TAC) was compared. Regardless of the used heating methods...
-
Graphene field-effect transistor application for flow sensing
PublikacjaMicroflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC) and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall...
-
Areas of Updraft Air Motion in an Idealised Weather Research and Forecasting Model Simulation of Atmospheric Boundary Layer Response to Different Floe Size Distributions
PublikacjaPresented dataset is part of a numerical modelling study focusing on the analysis of the influence of sea ice floe size distribution (FSD) on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the up-drafts indicates that the FSD affects the total moisture content and the values of area averaged turbulent fluxes in the model domain. In fact, while convective updrafts...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publikacjamodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublikacjaThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
EFFECT OF PRESS DRYING ON DIMENSION STABILITY AND DENSITY OF BEECH WOOD,
PublikacjaTimber is traditionally dried in kilns by processes that often take several days or weeks to complete. At present, it is possible to apply several methods of rapid drying of timber, including, for example, press drying. This research is based on the use of this process. Drying was performed using the heating plates with a temperature of 160 °C. Three pressures were compared in the research 1.0 MPa, 1.4 MPa, and 1.8 MPa. The density...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublikacjaIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
PublikacjaThe present study is concerned with the numerical simulations of Ostwald-de Waele fluid flow in a wavy trapezoidal cavity in the presence of a heated cylinder situated at the center of the cavity. The work consists in characterizing the mixed convection as a function of the intensity of heat flow. The flow behaviour and temperature distribution in a cavity are the main focus of this study. The lower wall of the cavity is fixed...
-
Double-diffusive natural convection energy transfer in magnetically influenced Casson fluid flow in trapezoidal enclosure with fillets
PublikacjaThe prime motive of this disquisition is to deal with mathematical analysis of natural convection energy transport driven by combined buoyancy effects of thermal and solutal diffusion in a trapezoidal enclosure. Casson fluid rheological constitutive model depicting attributes of viscoelastic liquids is envisioned. The influence of the inclined magnetic field governed by Lorentz field law is also considered. To raise the essence...
-
Co-simulation strategy of transient CFD and heat transfer in building thermal envelope based on calibrated heat transfer coefficients
PublikacjaThe paper presents a strategy to develop a fully transient numerical model of a heat transfer in building, using a transient CFD model of indoor air and a thermal envelope model, running in a co-simulation. The strategy relies on the utilization of RANS with a high-Re turbulence model and a wall function, which enables to use a coarse computational mesh limiting the computational time. Since wall functions give invalid heat transfer...
-
Diurnal variability of atmospheric water vapour, precipitation and cloud top temperature across the global tropics derived from satellite observations and GNSS technique
PublikacjaThe diurnal cycle of convection plays an important role in clouds and water vapour distribution across the global tropics. In this study, we utilize integrated moisture derived from the global navigation satellite system (GNSS), satellite precipitation estimates from TRMM and merged infrared dataset to investigate links between variability in tropospheric moisture, clouds development and precipitation at a diurnal time scale. Over...
-
Modelling of saturated, subcooled and post-dryout flow boiling with the energy dissipation based semi-empirical model
PublikacjaA comprehensive semi-empirical model for saturated, subcooled and post dryout heat transfer is presented based on considerations of energy dissipation in the flow. The fundamental hypothesis in the model is the fact that heat transfer during flow boiling can be treated as a sum of two contributions constituting the total energy dissipation in the flow, namely the energy dissipation due to the shearing flow without the bubbles and...
-
Electromagnetic Control and Dynamics of Generalized Burgers’ Nanoliquid Flow Containing Motile Microorganisms with Cattaneo–Christov Relations: Galerkin Finite Element Mechanism
PublikacjaIn our research work, we have developed a model describing the characteristics of the bio-convection and moving microorganisms in the flows of a magnetized generalized Burgers’ nanoliquid with Fourier’s and Fick’s laws in a stretchable sheet. Considerations have been made to Cattaneo–Christov mass and heat diffusion theory. According to the Cattaneo–Christov relation, the Buongiorno phenomenon for the motion of a nanoliquid in...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...