Wyszukiwarka
Filtry
wszystkich: 212
wybranych: 211
Filtry wybranego katalogu
Wyniki wyszukiwania dla: THERMAL STRESSES
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublikacjaThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublikacjaThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
Evaluation of Thermal Stresses in Asphalt Layers Incomparison with TSRST Test Results
Publikacja -
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
The Impact of Thermal Stresses on Volume Resistivity: Performance Comparison between TR-XLPE and XLPE Cables
PublikacjaMost failures in electric power cables are attributed to the development of water trees inside the insulating materials. Thus, the development and utilization of Tree Retardant Cross-Linked Polyethylene (TR-XLPE) based cables have recently been given great attention to overcome the treeing issues. TR-XLPE cables use low-density polyethylene compounds suppressing the formation of water trees while retaining excellent electrical,...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Effects of Surface Energy and Surface Residual Stresses on Vibro-Thermal Analysis of Chiral, Zigzag, and Armchair Types of SWCNTs Using Refined Beam Theory
PublikacjaIn this article, vibration characteristics of three different types of Single-Walled Carbon Nanotubes (SWCNTs) such as armchair, chiral, and zigzag carbon nanotubes have been investigated considering the effects of surface energy and surface residual stresses. The nanotubes are embedded in the elastic substrate of the Winkler type and are also exposed to low and high-temperature environments. A new refined beam theory namely, one-variable...
-
Experimental and theoretical study on high-temperature creep of VT6 titanium alloy under multi-axial loading conditions
PublikacjaIn the framework of damage mechanics, we discuss a new mathematical model that describes the kinetics of the stress–strain state and damage accumulation during material degradation by the mechanism of long-term strength under complex multiaxial stress state. An experimental and theoretical technique is proposed for determination of material parameters and scalar constitutive functions for damaged media based on specially set experiments...
-
Extremal thermal loading of a bifurcation pipe
PublikacjaThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
Verification of the new viscoelastic method of thermal stress calculation in asphalt layers of pavements
PublikacjaThe new viscoelastic method of thermal stress calculations in asphalt layers has been developed and published recently by the author. This paper presents verification of this method. The verification is based on the comparison of the results of calculations with results of testing of thermal stresses in Thermal Stress Restrained Specimen Test. The calculations of thermal stresses according to the new method were based on rheological...
-
Impact of thermal loading into the structural performance of ships: A review
PublikacjaThe presented study reviews the recent advances done regarding the impact of thermal loading on the structural performance of ships. Firstly, the studies related to the mechanical and thermal properties of typical materials used in shipbuilding are outlined. Secondly, a brief introduction to the heat transfer analysis, Finite Element modelling and thermal stresses is provided. Finally, the review of papers dealing with the structural...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublikacjaThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublikacjaThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
The thermal effort during marine steam turbine flooding with water
PublikacjaThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Stability analysis of single-walled carbon nanotubes embedded in winkler foundation placed in a thermal environment considering the surface effect using a new refined beam theory
PublikacjaThis article is devoted to investigate the stability of different types of Single Walled Carbon Nanotubes (SWCNTs) such as zigzag, chiral, and armchair types which are rested in Winkler elastic foundations exposing to both the low and high temperature environments. Also, the Surface effects which include surface energy and surface residual stresses, are taken into consideration in this study. It may be noted that the surface energy...
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublikacjaThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Nanocrystalline cathode functional layer for SOFC
PublikacjaRecently, it was shown that thin functional layers introduced between an electrolyte and cathode might improve cathode performance. However, the mechanism of this improvement still needs analysis. In this paper, a thin (∼140 nm), spin-coated perovskite layer (La0.6Sr0.4Co0.2Fe0.8O3-δ) was placed between a cathode (La0.6Sr0.4Co0.2Fe0.8O3-δ) and an electrolyte (Ce0.8Gd0.2O2-δ) and the effects of this investigated. The microstructure...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublikacjaThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
On the non-linear dynamics of torus-shaped and cylindrical shell structures
PublikacjaIn this study, the non-linear dynamic analysis of torus-shaped and cylindrical shell-like structures has been studied. The applied material is assumed as the functionally graded material (FGM). The structures are considered to be used for important machines such as wind turbines. The effects of some environmental factors on the analysis like temperature and humidity have been considered. The strain field has been calculated in...
-
A concept of zero-dimensional and three-dimensional thermodynamic modelling of steam storage in a steam cycle
PublikacjaThis work presents the thermodynamic model of steam storage in a steam cycle. The innovative steam storage is an integral part of the unit and thus responds quickly to changes in load. This enhances the primary control reserve while maintaining high efficiency of energy conversion. With regard to power plants, it improves the operational safety of generation units, as it prevents boiler and turbines overload in the case of steep...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Investigation of low-temperature cracking in newly constructed high-modulus asphalt concrete base course of a motorway pavement
PublikacjaThe paper presents the issue of low-temperature transverse cracks which have developed in newly constructed base courses made of high-modulus asphalt concrete mix (HMAC). Numerous transverse cracks developed in the analysed HMAC base during the winter season before the pavement was actually completed, both at the transverse joint locations and in the areas between them. This had not happened so far on such a scale during road construction...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublikacjaIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublikacjaHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Experiments and Analysis of the Limit Stresses of a Magnetorheological Fluid
PublikacjaPaper presents the results of a rheological test of a commercial magnetorheological (MR) fluid (MRF-132DG). The researchincludes the problem of measuring and interpreting limit stresses under conditions close to the magnetic saturation of the fluid. Fourdifferent limit stresses were determined, two related to the yield point and two related to the flow point. Methods for determining limitstresses, especially due to excitation...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Application of Barkhausen method to determine internal stresses in cold-rolled and hot-rolled sheets
PublikacjaThe paper presents investigations on internal stress distribution in plane hot—or cold-rolled sheets dedicated for the cold-formed profiles. The motivation of the research is a new profile design whose bending technology, incorporating a longitudinal welded joint and hot-dip galvanization after bending and welding introduces additional internal stresses. In order to identify the entirety of stresses in the process of sheet production...
-
Mechanical Strength of MV Ship-switchgear During Fault Arc
PublikacjaIn the paper the analysis of pressure stressed in enclosure during fault arc inside switchgear is pre-sented as well. There is introduced the method based on determining stresses which are sum of tensile stresses (membrane) and deflection stresses. For tensile stresses nalysis the energy method, for unrestrainedly supported rectangular plate, was used. In the further part of the paper, the calculations and measurements results...
-
Bending of a Three-Layered Plate with Surface Stresses
PublikacjaWe discuss here the bending deformations of a three-layered plate taking into account surface and interfacial stresses. The first-order shear deformation plate theory and the Gurtin-Murdoch model of surface stresses will be considered and the formulae for stiffness parameters of the plate are derived. Their dependence on surface elastic moduli will be analyzed.
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublikacjaThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublikacjaTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublikacjaThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublikacjaThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
On stress singularity near the tip of a crack with surface stresses
PublikacjaIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
Sensitivity analysis of critical loads of I-columns
PublikacjaThe first order variation of critical buckling load of thin-walled columns with bisymmetric open cross-section due to some variations of the design variables such as: cross-section dimensions, or material characteristics is derived. The influence of the residual welding stresses is taken into account. In the numerical examples dealing with I-column the functions describing the effect of the variation of the dimensions of the flange...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublikacjaIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Laser Beam as a Precision Tool to Increase Fatigue Resistance in an Eyelet of Undercarriage Drag Strut
PublikacjaThe article contains the results of tests on a laser-processed eyelet of undercarriage drag strut to increase its fatigue strength. Laser processing concentrated on both sides around the hole of eye for connecting the undercarriage drag strut caused that the material in this area withstood more than twice the number of load cycles established for this material. In order to determine the reasons for the increase in fatigue strength,...
-
Identification of Shear Modulus Parameters of Half-space Inhomogeneous by Depth
PublikacjaThe paper propose a method for determining of the parameters of the exponential shear modulus of a functionally graded half-space based on the solution of the problem of a pure shear of an elastic functionally graded half-space by a strip punch. The solution of the integral equation of the contact problem is constructed by asymptotic methods with respect to the dimensionless parameter. The dependence of contact stresses on the...
-
Surface finite viscoelasticity and surface anti-plane waves
PublikacjaWe introduce the surface viscoelasticity under finite deformations. The theory is straightforward generalization of the Gurtin–Murdoch model to materials with fading memory. Surface viscoelasticity may reflect some surface related creep/stress relaxation phenomena observed at small scales. Discussed model could also describe thin inelastic coatings or thin interfacial layers. The constitutive equations for surface stresses are...
-
Application of Barkhausen effect in the impact assessment of welding to internal stress distribution in steel
PublikacjaThe paper presents identification method of internal stresses in plane steel elements in the chase of deliverance and welding assembly. The assessment was made by means of a non-destructive experimental method based on measurements incorporating local external magnetic field and the measurement of induced voltage, including Barkhausen noise. This method allows a degradation assessment due to internal and external actions, causing...