Wyszukiwarka
Wyniki wyszukiwania dla: mathematical models
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublikacjaThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Mind the framing: Match purpose and context
PublikacjaIn several ways, the following chapters will allude to the concept of frames. The assumptions of a mathematical model tell us what it can explain and what it cannot (see chapter 5). The trade-off between the usefulness of a mathemati- cal model and the scale of complexity it seeks to capture further conditions the narrative, highlighting or downsizing cognitive elements relevant to responsible modelling (see ‘Mathematics and tales’...
-
Biological processes modelling for MBR systems: A review of the state-of-the-art focusing on SMP and EPS
PublikacjaA mathematical correlation between biomass kinetic and membrane fouling can improve the understanding and spread of Membrane Bioreactor (MBR) technology, especially in solving the membrane fouling issues. On this behalf, this paper, produced by the International Water Association (IWA) Task Group on Membrane modelling and control, reviews the current state-of-the-art regarding the modelling of kinetic processes of biomass, focusing on...
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Negative impact of constant RPM control strategy on ship NOx emission in waves
PublikacjaIn severe wave conditions, the ship propulsion system is loaded with high fluctuations due to external disturbances. The highly fluctuating loads enforce radical changes in the main engine torque, which in turn demands variation of the fuel rate injected into the cylinders if a constant rotational speed strategy is applied. Therefore, the temperature of gases varies to a large extent during the combustion process in the cylinders....
-
The effect of shear deformations' rotary inertia on the vibrating response of multi-physic composite beam-like actuators
PublikacjaIn consecutive studies on flexomagneticity (FM), this work investigates the flexomagnetic reaction of a vibrating squared multi-physic beam in finite dimensions. It is assumed that the bending and shear deformations cause rotary inertia. In the standard type of the Timoshenko beam the rotary inertia originated from shear deformations has been typically omitted. It means the rotary inertia resulting from shear deformation is a new...
-
The Positioning Accuracy of BAUV Using Fusion of Data from USBL System and Movement Parameters Measurements
PublikacjaThe article presents a study of the accuracy of estimating the position coordinates of BAUV (Biomimetic Autonomous Underwater Vehicle) by the extended Kalman filter (EKF) method. The fusion of movement parameters measurements and position coordinates fixes was applied. The movement parameters measurements are carried out by on-board navigation devices, while the position coordinates fixes are done by the USBL (Ultra Short Base...
-
A few steps more towards NPT bound entanglement
PublikacjaIn this paper, existence of bound entangled states with nonpositive partial transpose (NPT) is considered. As one knows, existence of such states would in particular imply nonadditivity of distillable entanglement. Moreover, it would rule out a simple mathematical description of the set of distillable states. The particular state, known to be 1-copy nondistillable and supposed to be bound entangled, is considered. The problem of...
-
Optimization of Saccharification Conditions of Lignocellulosic Biomass under Alkaline Pre-Treatment and Enzymatic Hydrolysis
PublikacjaPre-treatment is a significant step in the production of second-generation biofuels from waste lignocellulosic materials. Obtaining biofuels as a result of fermentation processes requires appropriate pre-treatment conditions ensuring the highest possible degree of saccharification of the feed material. An influence of the following process parameters were investigated for alkaline pre-treatment of Salix viminalis L.: catalyst concentration...
-
Arching of railway turnouts by analytical design method
PublikacjaThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Ice Phenomena in River Mouths
PublikacjaRiver outlets located in tideless areas are analyzed in this paper. First, ice processes in the St Clair River mouth are presented. The river mouth, called St. Clair Flats is a typical river delta located on the shore of Lake St. Clair. Based on this example ice jam formation in river delta has been analyzed followed by a presentation of the main mechanism of ice jam formation. The Vistula River mouth is a man-made, artificial...
-
Implementation of Hierarchical Control of Drinking Water Supply System
PublikacjaThe paper presents the outline of the didactical project of a complex computer controlled system realized by the first degree students of the Automatics and Robotics on the Faculty of Electrical and Control Engineering (FoEaCE) in Gdansk University of Technology (GUT). The synthesis, implementation and analysis of a multilayer hierarchical control system for drinking water supply system (DWSS) are main topics of that project. The...
-
A Development of a Capacitive Voltage Divider for High Voltage Measurement as Part of a Combined Current and Voltage Sensor
PublikacjaThis article deals with the development of capacitive voltage divider for high voltage measurements and presents a method of analysis and optimization of its parameters. This divider is a part of a combined voltage and current sensor for measurements in high voltage power networks. The sensor allows continuous monitoring of the network distribution status and performs a quick diagnosis and location of possible network failures....
-
Machine Learning Techniques in Concrete Mix Design
PublikacjaConcrete mix design is a complex and multistage process in which we try to find the best composition of ingredients to create good performing concrete. In contemporary literature, as well as in state-of-the-art corporate practice, there are some methods of concrete mix design, from which the most popular are methods derived from The Three Equation Method. One of the most important features of concrete is compressive strength, which...
-
Analytical design method for widening the intertrack space
PublikacjaThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublikacjaPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Marine traffic risk modelling – an innovative approach and a case study
PublikacjaThis paper presents a model to analyse the risk of two common marine accidents: collision and grounding. Attention is focused on oil tankers since they pose the highest environmental risks. A case study in selected areas of the Gulf of Finland in ice-free conditions is presented. The model utilizes a formula for risk calculation that considers both the probability of an unwanted event and its consequences. The model can be decomposed...
-
Mathematical Modeling of Ice Thrusting on the Shore of the Vistula Lagoon (Baltic Sea) and the Proposed Artificial Island
PublikacjaCoastal lagoons are inland and shallow water bodies, separated from the ocean by a barrier. In cold regions, ice phenomena in shallow water coastal lagoons occur every winter season. Ice is predominantly formed on the surface due to density stratification and surface cooling. The ice dynamics in such areas are dominantly affected by winds. Water dynamics also cause ice movement, but due to the large areal scale of lagoons, the...
-
Advanced Supervisory Control System Implemented at Full-Scale WWTP—A Case Study of Optimization and Energy Balance Improvement
PublikacjaIn modern and cost-eective Wastewater Treatment Plants (WWTPs), processes such as aeration, chemical feeds and sludge pumping are usually controlled by an operating system integrated with online sensors. The proper verification of these data-driven measurements and the control of different unit operations at the same time has a strong influence on better understanding and accurately optimizing the biochemical processes at WWTP—especially...
-
A Robust Random Forest Model for Classifying the Severity of Partial Discharges in Dielectrics
PublikacjaPartial Discharges (PDs) are a common source of degradation in electrical assets. It is essential that the extent of the deterioration level of insulating medium is correctly identified, to optimize maintenance schedules and prevent abrupt power outages. Temporal PD signals received from damaged insulation, collected through the IEC-60270 method is the gold standard for PD detection. Temporal signals may be transformed to the frequency...
-
Kriging-assisted hybrid reliability design and optimization of offshore wind turbine support structure based on a portfolio allocation strategy
PublikacjaIn recent years, offshore wind power generation technology has developed rapidly around the world, making important contributions to the further development of renewable energy. When designing an Offshore Wind Turbine (OWT) system, the uncertainties in parameters and different types of constraints need to be considered to find the optimal design of these systems. Therefore, the Reliability-Based Design Optimization (RBDO) method...
-
Simplified Numerical Model for Transient Flow of Slurries at Low Concentration
PublikacjaRapid transients are particularly dangerous in industrial hydro-transport systems, where solid-liquid mixtures are transported via long pressure pipelines. A mathematical description of such flow is difficult due to the complexity of phenomena and difficulties in determining parameters. The main aim of the study was to examine the influence of the simplified mixture density and wave celerity description on satisfactory reproduction...
-
Electromagnetic Control and Dynamics of Generalized Burgers’ Nanoliquid Flow Containing Motile Microorganisms with Cattaneo–Christov Relations: Galerkin Finite Element Mechanism
PublikacjaIn our research work, we have developed a model describing the characteristics of the bio-convection and moving microorganisms in the flows of a magnetized generalized Burgers’ nanoliquid with Fourier’s and Fick’s laws in a stretchable sheet. Considerations have been made to Cattaneo–Christov mass and heat diffusion theory. According to the Cattaneo–Christov relation, the Buongiorno phenomenon for the motion of a nanoliquid in...
-
Intensification of catechin extraction from the bark of Syzygium cumini using ultrasonication: Optimization, characterization, degradation analysis and kinetic studies
PublikacjaCatechin is a prominent polyphenolic component that possesses various medicinal properties. Present work communicates the intensification and optimization of catechin extraction from the bark of Syzygium cumini tree using stirred reactor, soxhlet, ultrasonic bath, and ultrasonic horn technique. The optimization of several parameters such as type of solvent, solid to solvent ratio (1:100 w/v), speed of agitation (300 RPM), extraction...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
Designing of Track Axis Alignment with the Use of Satellite Measurements and Particle Swarm Optimization
PublikacjaDesigning of the track’s alignment is a key issue from the point of view of maintaining of proper geometries. The paper presents a design method for sections of railway line located in the horizontal arch. The method is adapted to the technique of mobile satellite measurements. The general principles of this measurement method have been described in the article. A project's solution has been presented using mathematical notation...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Optimization of thermal backfill configurations for desired high-voltage power cables ampacity
PublikacjaThe ampacity of high-voltage power cables depends, among others, on their core cross-sectional area as well as thermal resistivity of the thermal backfill surrounding the cables. The cross-sectional area of the power cables’ core is selected according to the expected power to be transferred via the cable system. Usually, the higher the power transfer required, the higher the cross-sectional area of the core. However, the cost of...
-
Suppression of Supply Current Harmonics of 18-Pulse Diode Rectifier by Series Active Power Filter with LC Coupling
PublikacjaThe reported research aims at improving the quality of three-phase rectifier supply currents. An effective method consists of adding properly formed booster voltages to the fundamental supply voltages using a series active filter. In the proposed solution, the booster voltages are generated by three single-phase systems consisting of inverters, LC filters, and single-phase transformers. The application of LC couplings ensures low...
-
Long Distance Geographically Distributed InfiniBand Based Computing
PublikacjaCollaboration between multiple computing centres, referred as federated computing is becom- ing important pillar of High Performance Computing (HPC) and will be one of its key components in the future. To test technical possibilities of future collaboration using 100 Gb optic fiber link (Connection was 900 km in length with 9 ms RTT time) we prepared two scenarios of operation. In the first one, Interdisciplinary Centre for Mathematical...
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublikacjaThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
Evaluation of ChatGPT Applicability to Learning Quantum Physics
PublikacjaChatGPT is an application that uses a large language model. Its purpose is to generate answers to various questions as well as provide information, help solve problems and participate in conversations on a wide range of topics. This application is also widely used by students for the purposes of learning or cheating (e.g., writing essays or programming codes). Therefore, in this contribution, we evaluate the ability of ChatGPT...
-
Impact of the type of heat exchanger on the characteristics of low-temperature thermoacoustic heat engines
PublikacjaThermoacoustic technologies are considered an effective solution for harnessing low-temperature heat, whether from waste or renewable sources. However, in practice, developing and implementing high-performance ther- moacoustic systems is a complex challenge. In real waste heat recovery systems, heat exchange between ther- moacoustic engines (TAEs) and external heat sources is facilitated by auxiliary systems, such as circulation...
-
Measured and predicted freeze-thaw days frequencies in climate change conditions in central Poland
PublikacjaThe rate of progression of geomorphological phenomena is greatly influenced by freeze-thaw processes. In the face of air temperature increasing over the past few decades, a question of the future impact of these processes arises, notably in the temperate and cold climate zones. Using the mean, maximum and minimum daily air temperature data in the period 1951–2018 obtained from three weather stations located in the vicinity of Jeziorsko...
-
MATHEMATICAL MODELING OF FLOOD MANAGEMENT SYSTEM IN THE CITY OF GDAŃSK, ORUŃSKI STREAM CASE STUDY
PublikacjaAim of the study This study analyses the efficiency of flood protection in a small urban catchment, based on a system of small reservoirs. Material and methods To assess the flood routing and surge reduction, a mathematical model of the river catchment was implemented. This was a lumped hydrological model, based on the SCS-CN method. Channel routing was performed, using kinematic wave equation. The sub-catchments have been determined...
-
The atlas of inequality aversion: theory and empirical evidence on 55 countries from the Luxembourg Income Study database
PublikacjaResearch background: In the distributive analysis, the constant relative inequality aversion utility function is a standard tool for ethical judgements of income distributions. The sole parameter ε of this function expresses a society’s aversion to inequality. However, the profession has not committed to the range of ε. When assessing inequality and other welfare characteristics, analysts assume an arbitrary level of ε, common...
-
Switching Regulation in the Control of 5-Phase Permanent Magnet Synchronous Motor Fed by 3×5 Direct Matrix Converter
PublikacjaMatrix converter is an AC-AC direct power converter comprising of an array of bi- directional switches. It does not require an intermediate DC-link and allows sinusoidal output waveforms with varying amplitudes and frequencies. The configuration of these bi- directional switches decides the number of inputs and outputs...
-
Development, characterization and evaluation of composite adsorbent for the adsorption of crystal violet from aqueous solution: Isotherm, kinetics, and thermodynamic studies
PublikacjaThe purpose of this work focuses on the production and investigations of a new composite material as alternative low-cost adsorbent for the removal of crystal violet (CV) dye from waste solution. The production method was performed by in-situ thermal activation technology via extrusion process of polymer wastes containing tire rubber (50 wt%) and polyurethane foam (50 wt%) using single-screw extruder under processing temperature...
-
Analytical ‘Steady-State’-Based Derivation and Clarification of the Courant-Friedrichs-Lewy Condition for Pipe Flow
PublikacjaThis article addresses the problem of choosing the optimal discretization grid for emulating fluid flow through a pipeline. The aggregated basic flow model is linearized near the operating point obtained from the steady state analytic solution of the differential equations under consideration. Based on this model, the relationship between the Courant number (μ) and the stability margin is examined. The numerically set coefficient...
-
An Analysis of Contextual Aspects of Conceptualization: A Case Study and Prospects
PublikacjaIn this chapter we present a new approach to development of modularized knowledge bases. We argue that modularization should start from the very beginning of modeling, i.e. from the conceptualization stage. To make this feasible, we propose to exploit a context-oriented, semantic approach to modularization. This approach is based on the Structural Interpretation Model (SIM) presented earlier elsewhere. In the first part of thischapter...
-
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
THE APPLICATION EFFECTS OF CONTINUOUS SATELLITE MEASUREMENTS OF RAILWAY LINES
PublikacjaThe paper presents results of satel lite surveying of the railway's rout es, which have been conducted just after starting in Poland (in 2008) the Active Geodesy Network ASG-EU POS. Afterwards it was possible to effectively utilize the GNSS survey ing results for the inventory of the (exploring) railways in service. Already at the beginning of 2009, the research team from Gdansk University of Technology and Naval Academy in Gdynia,...
-
FURTHER REMARKS ON THE NEO-CLASSICAL NAVIER-STOKES EQUATIONS
PublikacjaThe seminal Navier-Stokes equations have been stated yet before creation of principles of thermodynamics and the first and second laws. In the literature there is the common opinion that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of “working fluid” which is able to describe transformation of “ heat” into “work” and vice versa. Therefore, in the paper, a new exposition of thermodynamically...
-
Simulating propagation of coherent light in random media using the Fredholm type integral equation
PublikacjaStudying propagation of light in random scattering materials is important for both basic and applied research. Such studies often require usage of numerical method for simulating behavior of light beams in random media. However, if such simulations require consideration of coherence properties of light, they may become a complex numerical problems. There are well established methods for simulating multiple scattering of light (e.g....
-
Biorefinery Approach for H2 and Acids Production Based on Uncontrolled pH Fermentation of an Industrial Effluent
PublikacjaIn this work, the feasibility of uncontrolled pH acidogenic fermentation of industrial organic effluent from corn-bioethanol production was studied and modelled by using a Monod-based mathematical model. In order to do that, several tests were carried out at different initial pH values, ranging from 4 to 6. The experimental data showed a pH reduction during the fermentation process due to the generation of short-chain acids. When...
-
Experimental study and numerical simulation on porosity dependent direct reducibility of high-grade iron oxide pellets in hydrogen
PublikacjaThe transition to more environmentally friendly steel production methods has intensified research into hydrogen-based direct reduction (HyDR) of iron oxide pellets. The aim of this study is to systematically investigate the kinetics of the reduction process, the evolution of porosity and the resulting microstructural changes on the reduction behavior of high-quality pellets during HyDR of iron ore at different temperatures. A modified...
-
Risk Assessment Due To Customs Delays In Supply Chains By Fuzzy Logic
PublikacjaDue to violations of existing trade relations, cargo flows between the European Union and Ukraine have been redistributed. As a result, new supply chains have been created that have increased the tension on ground transport, including road and rail. Unfortunately, this has caused significant delays when crossing the border, which has led to a greater increase in the total delivery time of goods. Therefore, to plan for effective...
-
Risk Assessment at Unsignalized Intersections Based on Human-Road-Environment-Vehicle System Applying Fuzzy Logic
PublikacjaThe constant increase in motorization level and traffic density increases risks due to dangerous situations for road participants. Therefore, assessing the accident level of road network elements has been an urgent task over the past decades. However, existing approaches mainly rely on traffic flow parameters and account for dynamic vehicle characteristics. The research aims to design a model accounting for uncertain factors (weather...
-
Towards Resource Theory of Coherence in Distributed Scenarios
PublikacjaThe search for a simple description of fundamental physical processes is an important part of quantum theory. One example for such an abstraction can be found in the distance lab paradigm: if two separated parties are connected via a classical channel, it is notoriously difficult to characterize all possible operations these parties can perform. This class of operations is widely known as local operations and classical communication....