Wyszukiwarka
Filtry
wszystkich: 2235
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MICRO-TURBINE DYNAMICS
-
„Eulerian – Eulerian” versus ,,Eulerian –Lagrangean” models of condensation
PublikacjaLiquid phase in the flowing vapor through stages of the steam turbine is the cause of a lot of failures. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current. The formation of drops of condensate under conditions other than nominal operation of turbine is a process still unknown. Engineers and designers involved in the development of power station machines...
-
Comparative study of selected fluids for use in supercritical Organic Ranking Cycles
PublikacjaIn view of increasing interest in improving energy efficiency of energy conversion devices, there is an increasing requirement of combined production of heat and electricity as well as demand for increased implementation of renewable energy resources. The micro cogenerative units utilizing the Organic Rankine Cycle are focusing the attention of many research centres around the world. In the present paper calculations of ORC cycles...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
A Preliminary Study and Analysis of Tidal Stream Generators
PublikacjaFor a sustainable future, tidal energy can play a vital role. Tidal energy relies on the gravitational pull of the Moon and the Sun along with the centrifugal forces created by the Earth. Tidal barrage uses the potential energy from the tide and has been very successful in electricity production. With the help of a turbine, kinetic energy can also be harnessed from tidal currents to generate electricity. However, it is not economically...
-
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
Kursy OnlineLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublikacjaThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
Micro- and nanodosimetry
Kursy OnlineMicro- and nanodosimetry (Mikro- i nanodozymetria) dla studentów studiów II stopnia WFTIMS
-
Marek Czachor prof. dr hab.
Osoby -
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublikacjaThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublikacjaThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Aerodynamic Shape Optimization for Delaying Dynamic Stall of Airfoils by Regression Kriging
PublikacjaThe phenomenon of dynamic stall produce adverse aerodynamic loading which can adversely affect the structural strength and life of aerodynamic systems. Aerodynamic shape optimization (ASO) provides an effective approach for delaying and mitigating dynamic stall characteristics without the addition of auxiliary system. ASO, however, requires multiple evaluations time-consuming computational fluid dynamics models. Metamodel-based...
-
Drivetrain of a Wind Turbine
PublikacjaIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
VEHICLE DYNAMICS (2024)
Kursy Online(W) Vehicle dynamics (W-Lecture) - DAPE - WIMiO The course entitled "Vehicle dynamcs" (VD) is conducted for the DAPE WIMiO Students. The VD course is to discuss the following problems: - major problems of vehicle dynamics from the application point of view, - definition of working environment, - types of vehicles, - parameters and characteristics of vehicles, - assessment of performance of vehicles towards design, -...
-
Quantum structure in competing lizard communities
PublikacjaAlmost two decades of research on applications of the mathematical formalism of quantum theory as a modeling tool in domains different from the micro-world has given rise to many successful applications in situations related to human behavior and thought, more specifically in cognitive processes of decision-making and the ways concepts are combined into sentences. In this article, we extend this approach to animal behavior, showing...
-
Visualization of the surface of the Nafion membrane
Dane BadawczeFuel cells use the chemical energy of hydrogen or other fuels to produce electricity. If the fuel is hydrogen, the only products are electricity, water and heat. Fuel cells are unique in the variety of their potential applications, they can use a wide variety of fuels. They are also highly scalable devices that can power both cars and mobile phones....
-
MODELOWANIE TURBINY WIATROWEJ Z DWOMA PRZECIWBIEŻNIE OBRACAJĄCYMI SIĘ WIRNIKAMI
PublikacjaW artykule przedstawiono sposoby modelowania dwuwirnikowej turbiny wiatrowej z wykorzystaniem technik Obliczeniowej Mechaniki Płynów. Omówiono uproszczone metody modelowania Actuator Disc i Actuator Line Method oraz aspekty związane z dokładnym odwzorowaniem turbiny na siatce obliczeniowej. Zaprezentowano przykładowe wyniki obliczeń turbiny dwuwirnikowej złożonej z wirników NREL o mocy nominalnej 5 MW każdy. Do wykonania badań...
-
MICRO
Czasopisma -
SELECTED PROBLEMS OF MACHINE DYNAMICS (2024)
Kursy OnlineThe course is devoted towards lectures assocuated with the novel issues of machine and structures dynamics. The following lectures will be given during the SPMD course: - introduction to selected problems of machine dynamics, - definition of the machine and structure working environment, - internal and external loads on machines and structures, - dynamics of machines and structures, - strength of machines and structures, - special...
-
Hyperelastic Microcantilever AFM: Efficient Detection Mechanism Based on Principal Parametric Resonance
PublikacjaThe impetus of writing this paper is to propose an efficient detection mechanism to scan the surface profile of a micro-sample using cantilever-based atomic force microscopy (AFM), operating in non-contact mode. In order to implement this scheme, the principal parametric resonance characteristics of the resonator are employed, benefiting from the bifurcation-based sensing mechanism. It is assumed that the microcantilever is made...
-
Selected Problems of Machine Dynamics
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics II
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Flow Analysis of a Kaplan Turbine
PublikacjaThis monograph is a guide to a method of experimental and numerical flow investigations for Kaplan - type turbines. The numerical calculations were compared with the test results of the model Kaplan turbine. The tests were carried out on the model test rig in the Gdańsk University of Technology. The turbine has been thoroughly experimentally investigated, resulting in the identification of optimum setting combination of the stator...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublikacjaIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
Pressure Pulsations in Turbine Blade Seal
PublikacjaThe paper presents the results of experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type. The performed experimental research proved that in a shroud clearance the pressure pulsates and the effects of the nozzle trailing edge thickness as well as the influence of the rotor blades are observed. The exemplary results...
-
Balancing energy processes in turbine engines
PublikacjaThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublikacjaThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
ANALYSIS OF WORKING CONDITIONS OF BEARINGS NO.1 & NO.2 OF TURBINE 13K200 AND DESIGN DEVELOPMENT OF NEW BEARINGS FOR THE TURBINE AFTER RETROFITTING
PublikacjaThe main goal of the work consisted of preparing an analysis of working conditions of bearings No.1 and No.2 in the existing turbine 13K200, as well as designing geometries of new bearings which would allow for their proper functioning in the turbine following its retrofitting (work under higher load).
-
Control of the wind turbine generator
PublikacjaWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Dynamic model of nuclear power plant turbine
PublikacjaThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
Micro and Nanosystems
Czasopisma -
IEEE MICRO
Czasopisma -
Micro and Nanostructures
Czasopisma -
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublikacjaThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
Proposition of the steam turbine governor structure modification
PublikacjaThere is considered the steam turbine governor operation during defense and restoration of the power system. It points out weaknesses of currently used governor structures. The new controller is proposed, that takes advantages of those curently used. The new controller allows for more effective control of the turbine in emergency situations, at frequencies much different from the nominal value.
-
Complex multidisciplinary optimization of turbine blading systems
PublikacjaThe paper describes the methods and results of direct optimization of turbine blading systems using a software package Opti_turb. The final shape of the blading is obtained from minimizing the objective function, which is the total energy loss of the stage, including the leaving energy. The current values of the objective function are found from 3D RANS computations (from a code FlowER) of geometries changed during the process...
-
Organic Supercritical Thermodynamic Cycles with Isothermal Turbine
PublikacjaOrganic Rankine cycles (ORC) are quite popular, but the overall efficiencies of these plants are rather very low. Numerous studies have been conducted in many scientific centers and research centers to improve the efficiency of such cycles. The research concerns both the modification of the cycle and the increase in the parameters of the medium at the inlet to the turbine. However, the efficiency of even these modified cycles rarely...
-
Pressure pulsations in turbine blade seal clearance
PublikacjaThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...
-
Neural Modelling of Steam Turbine Control Stage
PublikacjaThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
[EiF] Economic theory - micro
Kursy Online{mlang pl} Dyscyplina: Ekonomia i Finanse Zajęcia obowiązkowe dla doktorantów I i II roku Prowadzący: dr hab. Tomasz Brodzicki Liczba godzin: 30 h Forma zajęć: wykład {mlang} {mlang en} Discipline: Economics and Finance Obligatory course for 1st and 2nd year PhD students Academic teacher: dr hab. Tomasz Brodzicki Total hours of training: 30 teaching hours Course type: lecture {mlang}
-
Dynamics of quantum entanglement
PublikacjaA model of discrete dynamics of entanglement of a bipartite quantum state is considered. It involves a global unitary dynamics of the system and periodic actions of local bistochastic or decaying channel. For initially pure states the decay of entanglement is accompanied by an increase of von Neumann entropy of the system. We observe and discuss revivals of entanglement due to unitary interaction of subsystems. For some mixed states...
-
Determination of Failure Causes of a Steam Turbine Casing
PublikacjaThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
New trends in development of micro heat exchangers for ORC's
PublikacjaIn the paper, new trends in development of micro heat exchangers for CHP are presented. Main attention is concentrated on the question, how channels size and thermal development lenght affect the heat transfer. New types of micro heat exchangers developed at the Institute of Fluid-Flow Machinery PAS and the methoda of their design are presented. The new experimental testing methods of the micro-channel heat exchangers, new algorithms...
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublikacjaThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
Modelling of Nuclear Power Plant Steam Turbine
PublikacjaThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Modelling of Nuclear Power Plant Steam Turbine
PublikacjaThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...