Wyszukiwarka
Filtry
wszystkich: 2158
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLYMER DERIVED CERAMICS
-
Growth of polymer brushes by “grafting from” via ATRP – Monte Carlo simulations
Publikacja -
Morphology of the sol-gel derived LTO:Cu films
Dane BadawczeMorphology of the lithium titanate doped by Cu thin films were investigated by SEM microscope. Films were deposited by spin-coater from sol-gel derived sol. SEM images showed a high porous structure, tipaciall for sol-gel based films. For measurements samples with a various content of Cu were selected.
-
Nitrogen dioxide sensing properties of PEDOT polymer films
PublikacjaThis work presents a simple and fully electrochemical route for the polymerization of poly(3,4-ethylenedioxytiophene) (PEDOT) films for fabricating a NO2 gas sensor prepared by electropolymerization of 3,4-Ethylenedioxythiophene (EDOT) monomer in lithium perchlorate/acetonitrile solution. The main aim of this study is to determine the sensing properties of conductive polymer at elevated temperatures. The effects of the humidity,...
-
From structure to luminescence investigation of oxyfluoride transparent glasses and glass-ceramics doped with Eu3+/Dy3+ ions
PublikacjaGlasses and glass-ceramics with nominal composition 73 TeO2– 4BaO– 3Bi2O3–18SrF2-2RE2O3 (where RE = Eu, Dy) have been synthesized by conventional melt-quenching technique and subsequent heat treatment at 370 °C for 24 h in air atmosphere. Various Eu3+ to Dy3+ molar ratio have been applied to investigate luminescence properties in both glass and glass-ceramic matrices. Especially, white light emission through simultaneous excitation...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublikacjaGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublikacjaCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Superconducting properties of BiPbSrCaCuO and BiSrCaCuO glass-ceramics
PublikacjaW pracy zbadano główne różnice pomiędzy właściwościami nadprzewodzącymi krystalizowanych szkieł BiPbSrCaCuO i BiSrCaCuO. Obie grupy materiałów wytwarzano w takich samych warunkach i zawierały one podobne ilości fazy nadprzewodzącej 2212. Mimo to, właściwości elektryczne w stanie normalnym oraz właściwości nadprzewodzące znacznie się różnią. Głównym źródłem różnic są różnice mikrostruktury obu grup materiałów.
-
Molten salt synthesis of conducting and superconducting ceramics
PublikacjaPublikacja przedstawia wyniki badań nadprzewoników oraz przewodników jonowych metodą syntezy w stopionej soli.
-
GOOD HEALTH PRODUCTS AND POLYMER COMPOSITES OBTAINED WITH THE USE OF NATURAL ORIGIN MICRO- AND NANOFIBERS
PublikacjaThe aim of this work was focused on good health products and polymer composites obtained with the use of natural origin micro- and nanofibers. Many different type of the natural plants are used in the production of good health products and polymer processing like curcuma, cellulose, microalgae and others. Often are used as a antioxidants and fillers. In this work the effect of algae and cellulose as a microfillers on the chosen...
-
Electronic and ionic relaxations in strontium-borate glass and glass-ceramics containing bismuth and vanadium oxides
PublikacjaThe topography, microstructure and electrical properties of strontium-borate glass and SBO glass containing bismuth and vanadium oxides, were studied. The structure was measured using X-ray diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDS) and Scanning electron microscope (SEM) methods. The A.C. complex conductivity was investigated as a function of temperature and frequency. The influence of the quantity of bismuth...
-
Experimental study on the effectiveness of polymer damper in damage reduction of temporary steel grandstand
PublikacjaA large number of accidents, involving collapses of temporary grandstands during different types of events, were observed in the past. If the synchronized movement of people is tuned with the natural frequency of the affected part of the structure, resonance might occur. It may lead to severe damages of grandstands, their collapse or panic among the spectators. The aim of the paper is to assess, through preliminary experimental...
-
Intercomparison of TEC obtained from the IRI model to the one derived from GPS measurements
PublikacjaIRI (International Reference Ionosphere) is a well-known standard of the ionosphere, but nowadays GPS permanent observations are also the base of the regional and global ionosphere models. In this paper, comparison of TEC (Total Electron Content) derived from the IRI model to the global TEC parameters derived from GPS measurements is presented. Global TEC maps show, that GPS derived ionosphere models, in opposition to the IRI,...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublikacjaThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
Nonlinear electrical properties of glass-ceramics nanocomposites containing ferroelectric nanocrystallites of Bi2VO5.5
PublikacjaNonlinear A.C. impedance measurements were conducted in the 50BiV-50SrBAlO nanocomposite as a function of frequency, temperature and A.C. voltage. This material is ferroelectric below temperature of 730 K, and above 730 K is a good ion-conductor. For this nanocomposite a low A.C. voltage of 1 V rms is enough to observe high nonlinearities. The origin of these nonlinear effects depends on the temperature and frequency. In the high...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublikacjaThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublikacjaOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
IRANIAN POLYMER JOURNAL
Czasopisma -
Absorbing Boundary Conditions Derived Based on Pauli Matrices Algebra
PublikacjaIn this letter, we demonstrate that a set of absorbing boundary conditions (ABCs) for numerical simulations of waves, proposed originally by Engquist and Majda and later generalized by Trefethen and Halpern, can alternatively be derived with the use of Pauli matrices algebra. Hence a novel approach to the derivation of one-way wave equations in electromagnetics is proposed. That is, the classical wave equation can be factorized...
-
Polymer based thick films - material quality and interface resistance evaluation
PublikacjaThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
POWDER METALLURGY AND METAL CERAMICS
Czasopisma -
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublikacjaLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublikacjaThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublikacjaCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublikacjaSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Coffee Wastes as Sustainable Flame Retardants for Polymer Materials
PublikacjaDevelopment of green flame retardants has become a core part of the attention of material scientists and technologists in a paradigm shift from general purpose to specific sustainable products. This work is the first report on the use of coffee biowastes as sustainable flame retardants for epoxy, as a typical highly flammable polymer. We used spent coffee grounds (SCG) as well as SCG chemically modified with phosphorus (P-SCG)...
-
Investigation of solid polymer electrolyte gas sensor with different electrochemical techniques
PublikacjaIn this work solid polymer electrolyte (SPE) amperometric sulphur dioxide sensor is investigated. Nafion was used as a membrane electrode and 1M sulphuric acid as an internal electrolyte. Sensor response to sulphur dioxide was measured. Besides traditional constant voltage amperometry also different electrochemical techniques were used. Results obtained by these methods are compared.
-
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publikacja -
Naturally-derived hydrogels for 3D pancreatic tumor models: A short review
PublikacjaStatistics suggest a high proportion of mortality rate by pancreatic cancer, which is a solid tumor characterized by high heterogeneity and the presence of a complex extracellular matrix. The very low effectiveness of pancreatic cancer treatment roots in the high metastatic potential and drug resistance of this tumor. Therefore, the quest for efficient cellular models enabling precise mimicking in vivo conditions, and anticancer...
-
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublikacjaThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...
-
Analysis of the properties of the YSTF ceramics materials before and after reduction
Dane BadawczeThe valence of titanium in reduced YSTF ceramics materials was investigated. Ceramics were reduced by annealing in a hydrogen atmosphere. For comparison unreduced sample was also measured. Valance state was measured by XPS method.
-
Electrical properties of nanocrystalline Sm-doped ceria ceramics
PublikacjaWłaściwości ceramiki z cerii zależa zwykle silnie od struktury ziaren. W pracy przedstawiono właściwości elektryczne ceramiki z cerii domieszkowanej samarem wykonanje w technologii 'net shape' posiadającej strukturę nanokrystaliczną.
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublikacjaPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Conductivity and superconductivity of (Bi,Pb)4Sr3Ca3Cu4Ox glass-ceramics
PublikacjaAmorficzny materiał (Bi,Pb)4Sr3Ca3Cu4Ox w zależności od warunków wygrzewania może być albo granulastym materiałem albo silnie nieuporządkowanym metalem. W pracy przedstawiony jest wpływ mikrostruktury na właściwości elektryczne w stanie normalnym oraz przejście do stanu nadprzewodzącego.
-
Electrical and structural properties of Nb-doped SrTiO3 ceramics
PublikacjaPrzebadano wpływ zawartości niobu na strukturę i własności elektryczne tytanianu strontu. Zbadany został wpływ warunków redukcji i porowatości na właściwości materiału. Za optymalne uznano domieszkowanie niobem w wysokości 2% molowych.
-
Utilization of molten salt synthesis route in ceramics production
PublikacjaThe molten salt synthesis method is widely used to prepare ceramic powders for various applications e.g. piezoelectric devices or electrolytes for solid oxide fuel cells. The usage of this method workdwide is quite common especially in piezoelectric powder synthesis. In this work several application of the method is presented and the advantages of this route are numbered.
-
Conductivity and superconductivity of (Bi,Pb)4Sr3Ca3Cu4Ox glass-ceramics.
PublikacjaW układzie(Bi,Pb)-Sr-Ca-Cu-O poprzez krystalizację w fazie stałej można wytworzyć materiały o bardzo różnych właściwościach elektrycznych i nadprzewodzących. W zależności od warunków krystalizacji, można wytworzyć nadprzewodnik o temperaturze krytycznej między 8 a 105 st.K lub materiał nie przechodzący do stanu nadprzewodzącego. W pracy pokazano i przedyskutowano wpływ składu fazowego, struktury i mikrostruktury na przewodnictwo...
-
Microstructural and electrical properties of Y0.07Sr0.93-xTiO3 perovskite ceramics
PublikacjaIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Chemical composition analysis of the LSNO ceramics
Dane BadawczeThe chemical composition of a series of La-Sb-Nb-O ceramics manufactured by the solid-phase reaction method was analyzed. The samples with a various antimony content were measured by XPS method (OmicronNanotechnology UHV system). Analysis confirmed presence of elements: La, Sb, Nb.
-
Investigation of energy deposition and its optical imaging in polymer gel dosimeters
PublikacjaThis following chapter describes methods for verifying the absorbed dose during radiotherapy. Special attention is paid to the method using polymer-gel dosimeters, the dose reading of which is performed by means of Laser Computed Tomography. The chapter also includes considerations on alternative solutions for dosimetric measurements and various types of radiotherapy and their pros and cons. In addition, both the methods of structural...
-
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublikacjaA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Silicon oxycarbide ceramics as anodes for lithium ion batteries: influence of carbon content on lithium storage capacity
PublikacjaWe report here on the synthesis and characterization of silicon oxycarbide (SiOC) in view of its application as a potential anode material for Li-ion batteries. SiOC ceramics are obtained by pyrolysis of various polysiloxanes synthesized by sol–gel methods. The polysiloxanes contain different organic groups attached to silicon, which influence the chemical composition and the microstructure of the final ceramic product. The structure...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublikacjaThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Interferometric Sensor of Wavelength Detuning Using a Liquid Crystalline Polymer Waveplate
PublikacjaOperation of a polarization interferometer for measurement of the wavelength changes of a tunable semiconductor laser was investigated. A lambda/8 waveplate made from liquid crystalline polymer is placed in one of interferometers’ arms in order to generate two output signals in quadrature. Wavelength was measured with resolution of 2 pm in the wavelength range 628–635 nm. Drift of the interferometer, measured in the period of 500...
-
XPS analysis of strontium titanate ceramics
Dane BadawczeThe chemical composition of the strontium titanite doped with yttrium and iron ceramic samples was investigated. Samples of Y0.07Sr0.93Ti0.8Fe0.2 were prepared by solid phase reaction and sintered for 24 and 48 hours. Chemical composition was measured by UHV OmicronNanotechnology XPS system. The analysis confirmed the chemical composition of the ceramics...
-
Polymer Chemistry
Czasopisma -
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublikacjaA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publikacjan this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
Potential applications of by-products from the coffee industry in polymer technology – Current state and perspectives
PublikacjaCoffee is one of the most popular beverages in the world, and its popularity is continuously growing, which can be expressed by almost doubling production over the last three decades. Cultivation, processing, roasting, and brewing coffee are known for many years. These processes generate significant amounts of by-products since coffee bean stands for around 50% of the coffee cherry. Therefore, considering the current pro-ecological...
-
Polyolefins, commercial and alternative routes toward the world’s most important polymer
Kursy OnlineThe course will consist of lectures followed by discussions. Based on the gained knowledge the Students will be asked to prepare in teams a short essay how to economically produce a selected polyolefin and how to introduce the new product into the market.