Filtry
wszystkich: 1445
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL-ALUMINIUM BRACKET
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublikacjaAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublikacjaSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
The Effectiveness of Polymer Damper in Damage Reduction of Temporary Steel Grandstand
PublikacjaA large number of accidents involving damage of temporary grandstands during different types of events were observed in the past. The aim of the paper is to analyse numerically the effectiveness of a polymer damper in damage reduction of a temporary steel scaffolding grandstand exposed to dynamic load due to jumping. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublikacjaEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Resistance to cold cracking of steel joints of P460NL1 steel
PublikacjaPrzedstawiono wyniki badań odporności na zimne pękanie złączy spawanych ze stali przeznaczonej do pracy pod ciśnieniem. Badano równoczesny wpływ zawartości wodoru dyfundującego i energii liniowej na naprężenie krytyczne w próbie implant dla złączy spawanych elektrodami otulonymi i drutem proszkowym w osłonie gazów ochronnych. Stwierdzono wpływ energii liniowej jak i zawartości wodoru dyfundującego na odporność na zimne pękanie...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
NUMERICAL ANALYSIS OF RUBBER BUMPERS INFLUENCE ON THE COLLIDING STEEL STRUCTURES
PublikacjaProblem of collisions of neighbouring structures is one of the important issues related to the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of numerical investigation of dynamic behavior of closely-separated steel structures under seismic excitation. Modal and transient...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublikacjaThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublikacjaThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Corrosion Inhibition of Aluminium Alloy AA6063-T5 by Vanadates: Local Surface Chemical Events Elucidated by Confocal Raman Micro-Spectroscopy
PublikacjaChemical interactions between aqueous vanadium species and aluminium alloy AA6063-T5 were investigated in vanadate-containing NaCl solutions. Confocal Raman and X-ray photoelectron spectroscopy experiments were utilised to gain insight into the mechanism of corrosion inhibition by vanadates. A greenish-grey coloured surface layer, consisting of V+4 and V+5 polymerized species, was seen to form on the alloy surface, especially on...
-
Weldability of Underwater Wet-Welded HSLA Steel: Effects of Electrode Hydrophobic Coatings
PublikacjaThe paper presents the effects of waterproof coatings use to cover electrodes on the weldability of high-strength, low-alloy (HSLA) steel in water. With the aim of improving the weldability of S460N HSLA steel in water, modifications of welding filler material were chosen. The surfaces of electrodes were covered by different hydrophobic substances. The aim of the controlled thermal severity (CTS) test was to check the influence...
-
Tensile curve of E grade steel for shipbuilding
Dane BadawczeIn the shipbuilding industry, the risk of brittle fractures developing in constructions is limited by employing certified materials of specific impact strength, determined using the Charpy method (for a given design temperature) and by exercising control over the welding processes (technology qualification, supervision of production, tests of non-destructive...
-
The influence of plastic working on the selection properties of the nickel - aluminium alloy coatings = Wpływ obróbki plastycznej na wybrane właściwości powłok stopowych nikiel - aluminium
PublikacjaW pracy przedstawiono wyniki badań nad możliwością zastosowania technologii obróbki plastycznej (walcowania na zimno i gorąco, oraz prasowania) do kształtowania wybranych właściwości natryskiwanych płomieniowo powłok stopowych Ni-5%Al o strukturze jednofazowej, a mianowicie granicznego roztworu stałego , o maksymalnej 10% rozpuszczalności glinu w sieci krystalograficznej niklu. Celem pracy jest wstępna analiza możliwości zastąpienia...
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
Study of the formation of calcareous deposits on cathodically protected steel in Baltic sea water
PublikacjaPurpose – The purpose of this paper is to investigate whether the sedimentation of calcareous deposits occurs on cathodically protected steel in Baltic sea water. Design/methodology/approach – Steel electrodes were cathodically polarized in natural Baltic sea water at potential þ0.150 V vs Zn electrode in potentiostatic mode. During exposure chronoamperometric measurements were carried out. After the exposure, the electrode’s surface...
-
Impedance analysis of Portevin-Le Chatelier effect on aluminium alloy
Publikacja -
Fractal analysis of the bending-torsion fatigue fracture of aluminium alloy
Publikacja -
Aluminium surface treatment with ceramic phases using diode laser
Publikacja -
On the distribution of aluminium and magnesium oxides in wustite catalysts for ammonia synthesis
Publikacja -
Podatność złączy spawanych stopów aluminium na korozję warstwową.
PublikacjaPrzedstawiono wyniki badań trzech stopów grup Al-Mg i Al-Zn-Mg na korozję warstwową. Wykazano, że mimo zróżnicowanego składu odporność stopów jest podobna, zaś największa korozja występuje w spoinie.
-
Multiaxial Fatigue Behaviour of SLM 18Ni300 Steel
PublikacjaFatigue behaviour of SLM 18Ni300 steel under proportional bending-torsion loading is studied. The fatigue tests are conducted under pulsating loading conditions using tubular specimens with a transversal circular hole. Three ratios of the normal stress to shear stress are considered, namely σ/τ=4,σ/τ=2 and σ/τ = 4/3. Crack initiation sites were found for two diametrically opposite points around the hole, whose locations are governed...
-
Strucutral steel - tensile test results
Dane BadawczeModern floating structures such as ships, oil platforms and offshore wind towers are built mostly of structural steel. It is a material that is subject to requirements which, when met, allows the construction and safe operation of the structure throughout its entire work cycle. One of the basic criteria that a material must meet is its strength. The...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublikacjaAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublikacjaThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublikacjaStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steel
PublikacjaThe paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment...
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry
PublikacjaS235JR steel is used in many applications, but its resistance to the erosion processes has been poorly studied. To investigate this resistance, cavitation, and slurry erosion tests were conducted. These tests were carried out at different erosion intensities, i.e., different flow rates in the cavitation tunnel with a system of barricades and different rotational speeds in the slurry pot. The steel was tested as-received and after...
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublikacjaThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...
-
NONSTRUCTURAL STIFFNESS ASSESSMENT IN INSTRUMENTED STEEL BUILDINGS
PublikacjaLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media
Dane BadawczeThis dataset contains the results of high-resolution XPS obtained during evaluation of high corrosion inhibition efficiency of citric acid towards aluminium alloy 5754 in bicarbonate buffer pH=11. The exposition duration of samples to electrolytic environment was 100 min. Each sample was exposed at different citric acid concentration ranging from 0...
-
Response of a steel tank during earthquakes and mining tremors - experimental investigation
PublikacjaCylindrical steel tanks are very popular shell structures used to store the products of chemical and petroleum industries. Any failure might have disastrous consequences, therefore their safety and reliability is essential. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration...
-
Photocatalytic Decomposition of Air Pollutants using Electrodeposited Photocatalysts on Stainless Steel
PublikacjaThe aim of research was to develop an immobilization method for photocatalysts, which is an alternative to the sol-gel or dip coating methods and can be simply scaled up for technical applications. The investigated photocatalyst was TiO2, which was electrochemically deposited onto a cathode made of stainless steel. This deposited film was photocatalytically active. In order to enhance the photoactivity of the TiO2 film, commercially...
-
Estimation of nonstructural stiffness in instrumented steel frames
PublikacjaLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
Notch fatigue analysis and life assessment using an energy field intensity approach in 7050-T6 aluminium alloy under bending-torsion loading
PublikacjaThis paper studies the fatigue crack initiation and fatigue crack propagation of notched cylindrical bars made of 7050-T6 aluminium alloy subjected to multiaxial bending-torsion loading. The sites of crack initiation and the angles of crack initiation were successfully predicted from the distribution of the first principal stress at the notch surface. Fatigue crack initiation lives were computed through the new concept of energy...
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublikacjaTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
PublikacjaThe purpose of this work was to determine the essence of the influence of the impact velocity (5, 7, and 9 m/s) on Hertzian stresses and the erosion mechanism of ferritic-pearlitic S355J2 steel. The investigations were carried out using a slurry pot tester. S355J2 steel showed a strong sensitivity to changes in impact velocity. A significant increase in erosion rate was observed at a velocity of 9 m/s. This increase was 5-fold...
-
Investigation of polyurethane elastomer–steel joints using glass lacquer as an adhesive agent
PublikacjaThis article describes an innovative method of coupling polyurethane elastomer (based on polyurethane glycolysate) with constructional steel, by implementation of a Glaspur®—glass lacquer containing latent polyurethanes and monosilane adhesion promoters. The commonly applied coupling agent is Cilbond® 45SF glue or its derivatives. Additionally, glycolysate was synthesised from polyurethane waste and 1,3-propylene glycol in 6:1...
-
VIBRATION PROBLEMS OF AN EXAMPLE OF TEMPORARY STEEL GRANDSTAND UNDER HUMAN-INDUCED EXCITATION
PublikacjaLighter and slender structural members of a typical grandstand leads to a significant reduction in the frequencies, that is why such structures are more easily induced to vibrations. The aim of the present paper is to show the results of our experimental studies and the numerical analyses, focused on the behaviour of a part of a typical temporary steel grandstand under dynamic loads. The peak values of accelerations of a steel...
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublikacjaThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
Experimental study on the effectiveness of polymer damper in damage reduction of temporary steel grandstand
PublikacjaA large number of accidents, involving collapses of temporary grandstands during different types of events, were observed in the past. If the synchronized movement of people is tuned with the natural frequency of the affected part of the structure, resonance might occur. It may lead to severe damages of grandstands, their collapse or panic among the spectators. The aim of the paper is to assess, through preliminary experimental...
-
Case Study of Old Steel Riveted Railway Truss Bridge: From Material Characterization to Structural Analysis
PublikacjaThe structural analysis of an old steel riveted railway truss bridge located over the Maruska River on the Działdowo – Olsztyn, Poland railway line is performed in this paper to check its behaviour under today’s railway loads. The mechanical properties of construction steel extracted from the old steel bridge are investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer....
-
THE EFFECT OF NOTCH DEPTH ON CTOD VALUES IN FRACTURE TESTS OF STRUCTURAL STEEL ELEMENTS
PublikacjaIn elements of steel structures working at low temperatures, there is a risk of appearance of brittle fracture. This risk is reduced through the use of certified materials having guaranteed strength at a given temperature. A method which is most frequently used to determine brittle fracture toughness is the Charpy impact test, preformed for a given temperature. For offshore structures intended to work in the arctic climat e, the...
-
MnCo2O4 deposited by spray pyrolysis as a protective layer for stainless steel interconects
PublikacjaStainless steel interconnects working in Solid Oxide Fuel Cells stacks are exposed to high temperature resulting in their corrosion. Protective layers for the hydrogen and oxygen sides are necessary to protect the interconnect material, prolongate the stack lifetime and maintain the output power. In this paper MnCo2O4 protective layer for the oxygen side of the interconnect is deposited by spray pyrolysis and is examined.